Question about Dodge Durango

Open Question

2004 dodge durango dtc code po869,po932

From 2nd to 3rd gear is a hard shift, but i can unplug the pressure sensor and plug it back up and it shifts fine untill truck is shut off and pcm resets everthing swap out sensors and its not the pressure sensor, thinking maybe pcm or tcm but not sure and i dont want to throw parts at it..............NEED HELP PLEASE!!!!!

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
dustyboner
  • 331 Answers

SOURCE: transmission faul code po700

(DTC) CODE # P0700....Transmission Control System (MIL Request)

Translation:
Transmission Control Module (TCM) Malfunction or Failure.

P0700 Information Code

The Transaxle Control Module (TCM) monitors the malfunction of sensors and actuators relating to transaxle control. If any malfunction is detected, the TCM informs the PCM by sending a signal (P0700 code). P0700 means that a code has been set in the TCM.

This code is for information ONLY. If this code is present, check for transaxle codes.

So basically, the P0700 code is telling you to check the TCM for a transaxle DTC. The TCM can not turn on the check engine light so it has the PCM do it. It needs to be scanned with trans capable scanner to see what the trans code or problem is. You should have 1st, 2nd, and Reverse because the car is operating in limp-mode. Since you said the speedometer doesn't work, my guess would be a faulty (VSS) vehicle speed sensor.

Posted on Oct 13, 2008

Ad
  • 1 Answer

SOURCE: Transmission problem

I had a shifting problem. The car would start in the wrong gear and shift at wrong times. I repaced the governor postion sensor and tranny fluid and the problem has been fixed for several years. Did you replace the tranny fluid?

Posted on Mar 07, 2009

  • 119 Answers

SOURCE: automotive repair

The ECT (Engine Coolant Temp) sensor is most likely bad. Common problem with Saturns.

Posted on May 21, 2008

  • 1 Answer

SOURCE: 2002 DODGE GRAND CARAVAN STUCK IN 2ND/3RD, NO SPEEDOMETER...

the tcm is located in the fender well behind the bumper drivers side black box check the wiring for bad cannection,

let us know what you find there are thousands of us with the same problem

dan

Posted on Aug 13, 2008

short shadey
  • 421 Answers

SOURCE: 2003 Dodge DSL 2500 transmission shifting problems

sounds like you should start by dropping the pan and changing the filter, put cheap fluid in it or reuse the old fluid if its not too bad bring it to a shop and have a transmission flush performed with a good flush machine your valve body is sticking and this should clear things up please rate -jeff

Posted on Sep 05, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Was going to work today and the durango sounded funny when it shifted in to 3rd gear it just reved up and never shifted . Now i'm getting a check engine light and error code p0700


Code 700 is a generic code for a problem with the transmission or the control module. Normally there are other codes for specific components.
You'll probably need a transmission shop to take a look.

Sep 06, 2013 | 2004 Dodge Durango

1 Answer

I have a 1998 dodge Grand Caravan with codes P0700,P0734 & P0733. What does this mean?


P0700 is a informative transmission code, about some problem there; the P0733 and P0734 is the specific problem there.
I would first try changing the fluid and filter. Although the fluid may look like it is brand new, with 100K on the fluid, I can assure you that even if those miles were all highway at steady speed and no load that the fluid has deteriorated and no longer lubricating the internal parts properly and that there is some debris in the ******.If codes return and shifting problems are still present, there is definite internal failure, possibly the pump or in the clutches.
DTC P0733The powertrain control module (PCM) uses the crankshaft position (CKP) sensor, input speed sensor (ISS) and output speed sensor (OSS) to determine engine speed, input shaft speed and output shaft speed. These sensor readings are used to determine the current gear ratio and RPM slip across the torque converter. The PCM uses this information from the sensors to determine if the commanded gear matches the actual gear. During normal driving conditions, the PCM will adapt main line pressure via the pressure control (PC) solenoid to prevent slipping and harsh shifts. Shift solenoid 3 is used to apply or release third gear clutch. The PCM controls 3rd gear by controlling the ground for shift solenoid 3. The PCM will turn the solenoid OFF, open the driver circuit, when 3rd gear is commanded On to apply 3rd clutch. Shift solenoid 3 is supplied ignition voltage from the fuel pump relay whenever the PCM commands the fuel pump relay ON. DTC P0733 sets when 3rd clutch still slips after the PCM has commanded high main line pressure.DTC Parameters
DTC P0733 will set if the PCM detects an incorrect actual 3rd gear ratio when 3rd gear is commanded On when:- The condition exists for longer than 3 seconds (2001)*- The condition exists for longer than 3 seconds, 1 minute is allowed to elapse, then condition exists again for longer than 3 seconds (2000)- The high main line pressure has been commanded- The transaxle is in a forward gear- The input speed is greater than 224 RPM- The vehicle speed is greater than 5 km/h (3 mph)- The speed noise parameter = NO- The steady state ratio fail counter equals 255 for an in-gear failure, or the shift fail counter is greater than 100 on a downshift or upshift to 3rd gear (128=0 or normal operation)DTC P0733 diagnostic runs continuously once the above conditions have been met.
DTC P0733 is a type A DTC for 2000, type B for 2001.**Applicable to vehicles built after June 2000.
Diagnostic AidsImportant: If DTCs P0745, P0746, P0756, P0758, P0761, P0763, P0766, P0768 or P0789 is set, diagnose that DTC first. A diagnosed PC solenoid, shift solenoid 2, 3 or 4 low/high circuit fault DTC may have caused DTC P0733 to set.Important: If a shift solenoid performance DTC P0783, 4th gear stuck ON, is set, diagnose that DTC first. A 4th gear stuck ON may cause no 3rd gear, no 2nd gear, or TCC stuck Off.
Refer to Pressure Ports - Air Check and Parts Description for pressure apply points and for component/location description.
Possible causes of no 3rd gear are listed in the flowchart on the succeeding page.
Verify TRANSMISSION ISS and TRANSMISSION OSS read correctly on Scan tool.
Make sure the pressure control, shift 2, shift 3 and shift 4 solenoids are not intermittently sticking. A sticking shift solenoid 4 may cause 4th gear to be applied from an initial start resulting in no 3rd gear. Audible sound should be similar for all solenoids. A muffled tone indicates the need for replacement.
Check this pinout HERE
P0734 refer at ratio 4 gear, and the rocedure is the same.
Hope helps.

Jan 22, 2013 | 2003 Dodge Caravan

2 Answers

Shifting problems 02 Dodge Durango 46re


shift solenoid needs to be replaced or the speed sensor

Oct 18, 2012 | 2002 Dodge Durango

1 Answer

Codes p0700,p0733,p0734 dodge caravan 1997


P0700 is a informative transmission code, about some problem there; the P0733 and P0734 is the specific problem there.
I would first try changing the fluid and filter. Although the fluid may look like it is brand new, with 100K on the fluid, I can assure you that even if those miles were all highway at steady speed and no load that the fluid has deteriorated and no longer lubricating the internal parts properly and that there is some debris in the ******.If codes return and shifting problems are still present, there is definite internal failure, possibly the pump or in the clutches.
DTC P0733The powertrain control module (PCM) uses the crankshaft position (CKP) sensor, input speed sensor (ISS) and output speed sensor (OSS) to determine engine speed, input shaft speed and output shaft speed. These sensor readings are used to determine the current gear ratio and RPM slip across the torque converter. The PCM uses this information from the sensors to determine if the commanded gear matches the actual gear. During normal driving conditions, the PCM will adapt main line pressure via the pressure control (PC) solenoid to prevent slipping and harsh shifts. Shift solenoid 3 is used to apply or release third gear clutch. The PCM controls 3rd gear by controlling the ground for shift solenoid 3. The PCM will turn the solenoid OFF, open the driver circuit, when 3rd gear is commanded On to apply 3rd clutch. Shift solenoid 3 is supplied ignition voltage from the fuel pump relay whenever the PCM commands the fuel pump relay ON. DTC P0733 sets when 3rd clutch still slips after the PCM has commanded high main line pressure.DTC Parameters
DTC P0733 will set if the PCM detects an incorrect actual 3rd gear ratio when 3rd gear is commanded On when:- The condition exists for longer than 3 seconds (2001)*- The condition exists for longer than 3 seconds, 1 minute is allowed to elapse, then condition exists again for longer than 3 seconds (2000)- The high main line pressure has been commanded- The transaxle is in a forward gear- The input speed is greater than 224 RPM- The vehicle speed is greater than 5 km/h (3 mph)- The speed noise parameter = NO- The steady state ratio fail counter equals 255 for an in-gear failure, or the shift fail counter is greater than 100 on a downshift or upshift to 3rd gear (128=0 or normal operation)DTC P0733 diagnostic runs continuously once the above conditions have been met.
DTC P0733 is a type A DTC for 2000, type B for 2001.**Applicable to vehicles built after June 2000.
Diagnostic AidsImportant: If DTCs P0745, P0746, P0756, P0758, P0761, P0763, P0766, P0768 or P0789 is set, diagnose that DTC first. A diagnosed PC solenoid, shift solenoid 2, 3 or 4 low/high circuit fault DTC may have caused DTC P0733 to set.Important: If a shift solenoid performance DTC P0783, 4th gear stuck ON, is set, diagnose that DTC first. A 4th gear stuck ON may cause no 3rd gear, no 2nd gear, or TCC stuck Off.
Refer to Pressure Ports - Air Check and Parts Description for pressure apply points and for component/location description.
Possible causes of no 3rd gear are listed in the flowchart on the succeeding page.
Verify TRANSMISSION ISS and TRANSMISSION OSS read correctly on Scan tool.
Make sure the pressure control, shift 2, shift 3 and shift 4 solenoids are not intermittently sticking. A sticking shift solenoid 4 may cause 4th gear to be applied from an initial start resulting in no 3rd gear. Audible sound should be similar for all solenoids. A muffled tone indicates the need for replacement.
Check this pinout HERE
P0734 refer at ratio 4 gear, and the rocedure is the same.
Hope helps.

Apr 03, 2012 | 2003 Ford Focus

1 Answer

1998 Dodge RAM 1500 won't upshift, slips out of gear


have you dropped the pan to see whats the bands are set at, any debris in pan bottom, whats your governor pressure, if bands are ok, but gov pressures are not relative to speed 1 psi per mph up to 95-127psi, port is on pass side of case rear top right, scan tool would be very helpful, your must have mil light on for this problem, gov dtc's, replace gov transducer as gov solniod as a pair, no exceptions, also are there any 02 sensor dtc's, shorted to voltage, this wil make pcm do stupid things to trans shift, affecting gov signals. GOOD LUCK RDJRP

Jul 10, 2009 | 1999 Dodge Ram

1 Answer

I have the same code po753 will not shift in to o/d


Don't waste your time,the trans is smoked.

Jun 22, 2009 | 2004 Dodge Durango

1 Answer

99 dodge 3500 diesel wont shift past first gear


You have not down a scan of the TCM (transmission control module) for fault codes, you need that done first before throwing away money on parts that don't fix the problem.

Jul 06, 2017 | 1999 Dodge Ram

1 Answer

Durango won't shift into gears by itself


i have had a problem like this. i had to replace my transmission sensor. would recommend having the sensor tested and replaced if necessary.

Jun 01, 2009 | 2001 Dodge Durango

1 Answer

2002 Dodge Caravan, Tranny would shift, DTC P0700, P0725


replace the input speed sensor to transmission and the wiring pigtail all are available at your chrysler dealer take your vehicle registration in to the parts counter so they have your vin # to get the right part and it is the front of trans by fluid linres to radiator.

Mar 08, 2009 | 2002 Dodge Caravan

3 Answers

Dodge Durango Transmission Problem


Code 0753 means Transmission 3-4 shift solenoid or transmission relay circuit problem. The PCM (engine computer) is seeing an incorrect input electrically for the gear or speed it should be seeing. You will need to find a qualified transmission shop to diagnose the problem. Possible causes for the trouble code start with worn/dirty fluid, electrical repairs & transmission overhaul.

Feb 04, 2009 | 1999 Dodge Durango

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

449 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6924 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...