Question about 1994 Chevrolet K1500

Open Question

What color is the fusible link wire 2 a fuel pump on a 94 1500 chevy pickup

Color of fuelpump fusible link wire

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
freetek
  • 5568 Answers

SOURCE: install fuel pump on 1996 chevy 1500

Is the fuel pump really bad?

Our son's erstwhile Ford something had a shock sensitive switch that when tripped by a big pothole, shut the (electric) fuel pump off and had to be reset before it would function again.

Posted on Jul 02, 2008

Ad
  • 1 Answer

SOURCE: fuel problem in 97 chevy truck 1500

your fuel pressure regulator could be bad also check fuel pressure with a guage it should be about 55 to 65 pounds

Posted on Aug 28, 2008

  • 1596 Answers

SOURCE: I need to replace the fuel pump in my 1985 Chevy S10 Pickup.

EXACT PROCEDURE ! Please Rate Me Fairly for this!! Thank you And Good Luck !!


ELECTRIC PUMP

REMOVAL

  1. Before servicing the fuel pump the fuel system pressure must be relieved. See: Fuel Pressure Release
  2. Disconnect the negative battery cable.
  3. Raise the car on a hoist.
  4. Remove the fuel tank. See Fuel Tank / Service and Repair.
  5. Remove the fuel tank sending unit and pump assembly by turning the cam lock ring counterclockwise. Lift assembly from the fuel tank.
  6. Pull the fuel pump up into the attaching hose while pulling outward away from the bottom support. Take care to prevent damage to the rubber insulator and strainer during removal. After the pump assembly is clear of the bottom support, pull the pump assembly out of the rubber connector for removal. NOTE: Inspect the fuel pump attaching hose for any signs of deterioration. Also check the rubber sound insulator at the bottom of the pump. Replace damaged or deteriorated parts.
INSTALLATION
  1. Push the fuel pump assembly into the attaching hose.
  2. Position the fuel tank sending unit and pump assembly into the fuel tank. Use a new "O" ring seal. NOTE: Care should be taken not to fold over or twist the strainer when installing the sending unit as this will restrict the flow of fuel. Also, verify that the strainer does not block the full travel of the float arm.
  3. Install cam lock over the assembly and lock by turning clockwise.
  4. Reinstall fuel tank.
MECHANICAL PUMP

REMOVAL and INSTALLATION

NOTE: To ease pump installation, rotate the camshaft so the camshaft eccentric is out of the way of the fuel pump rocker arm.

  1. Disconnect fuel lines from fuel pump.
  2. Remove fuel pump mounting bolts and the fuel pump.
  3. Remove all gasket material from the pump and block gasket surfaces. Apply sealer to both sides of new gasket.
  4. Position gasket on pump flange and hold pump in position against its mounting surface. Make sure rocker arm is riding on camshaft eccentric.
  5. Press pump tight against its mounting. Install retaining screws and tighten them alternately.
  6. Connect fuel lines. Then operate engine and check for leaks.

Posted on Mar 22, 2009

mcgyver468
  • 710 Answers

SOURCE: where is the fuel pump shutoff switch located on a 1996 chevy silverado 1500 located

Should be on the passenger side kickplate below the glovebox and to the right. You may have to remove the plastic panel to access it or look for a small hole in it and feel around for the button

Posted on Apr 23, 2009

DOODYDOODYDO
  • 105 Answers

SOURCE: process to change fuel pump on 2001 chevy silverado 1500

DROP THE FUEL TANK MAKE SURE YOU GO ABOUT HALF WAY THEN UNHOOK ALL THE LINES AND TERMINALS SO AS TO NOT DAMAGE THEM ALSO YOU NEED TO RELEASE THE FUEL PRESSURE AT FUEL RAIL BEFORE REMOVING ANY LINES

Posted on Jul 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No fuel pump voltage 2008 chevy colorado pickup


WHAT DOES WORK ? WHEN YOU WASH DOWN ENGINE YOU NEED TO COVER/WRAP/ ENCLOSE ELECTRICAL ITEMS !!! COIL, ALTERNATOR, DISTRIBUTOR, CONTROL MODULES, ETC., OTHERWISE, YOU'VE GROUNDED OUT YOUR ELECTRICAL SYSTEM !!! USE COMPRESSED AIR TO BLOW OUT ALL MOISTURE FROM THESE ITEMS MENTIONED. POWER FOR FUEL PUMP SYSTEM COMES FROM BATTERY, TO A JUNCTION BLOCK TERMINAL, WHICH HAS FUSIBLE LINKS WHICH ACT LIKE FUSES,, TO PROTECT EACH SYSTEM . DON'T KNOW IF THATS YOUR PROBLEM , BUT STRANGER THINGS HAVE HAPPENED ! FUSIBLE LINK LOOKS LIKE A HEAVY GAGE WIRE, BUT COULD BE A SINGLE STRAND OF WIRE INSIDE INSULATION ! NEED TO BE REPLACED IN LIKENESS !!! YOUR VEHICLE NEEDS TO DRY OUT ! MAYBE I'M ALL WET ? BUT CHANCES FAVOR THE PREPARED MIND !!! YOU NEED TO UNDO WHAT YOU DID , MAKES SENCE, YES ? ITS WHEN YOUR PROBLEM CAME TO BE ! OTHERWISE, INSPECT EVERY WIRE IN THE FUEL PUMP CIRCUIT, ESPECIALLY THE GROUND WIRES !!! THEY ARE JUST AS IMPORTANT AS THE POWER WIRES, WITH OUT QUESTION ! YOUR RELAY GOT BACKSPLASHED LOOK HOW MANY WIRES GO THERE ! IT ALSO HAS ITS OWN FUSE. THINK I COVERED IT, GOOD LUCK , YOU JUST MIGHT FIX THE PROBLEM AND NOT REALIZE IT TILL IT STARTS !

Apr 02, 2013 | 2008 Chevrolet Colorado 2WD

1 Answer

What amperage is the fusible link at the fuel pump harness on a 2009 Hyundia Sonata


The dealer or a parts store (if they can order it) would know the necessary rating of the fusible link-the color code may also tell the correct amperage and gauge. If possible, might help if you take it with you when ordering a new one. Fusible links are cut out and replaced.

Jan 25, 2013 | 2009 Hyundai Sonata 2.4

2 Answers

NEED TO KNOW WHERE THE FUEL PUMP RELAY SWITCH IS FOR A 1998 CHEVY S10 TRUCK...


For the 1998 s10 theres no fuelpump switch, there is a fuelpump relay. the relay is in the engine compartment inside the fuse/relay box. the relay will be labeled on the inside cover of the fuse/relay box cover. besides the relay the only other problem for a fuelpump not working on these trucks is the fuelpump is bad or the wiring connector to the pump is bad.

Aug 27, 2011 | Chevrolet Chevy Cars & Trucks

1 Answer

1989 Chevy Silverado pickup starts when you put gas in carb but the fuel enjector will not spray fuel into carb


The first test would be the fuelpump, this sounds like the pump is not pump the fuel to injectors, as you said that if you give it fuel into throtlebody it will start. this tells me its not getting fuel and the most common reason is the fuelpump, a quick test that sometimes works is to have someone trying to start it while you beat the bottom of the tank with a rubber hammer, this sometimes shakes the pump and it makes contact and starts truck, if this happens then the pump is bad for sure, if it doesnt start then you will need to test for power and ground at the connector going to pump, this connector is locted neat the tank, you will see wires coming from the top of the tank going to frame, theres the connector to test. good day.

Apr 10, 2011 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

I have a 98 S-10 that was running and just stopped. We were told it was the fuel pump. Replaced it, but not getting power to the pump, no pressure in the fuel line and it will started once in awhile and...


Look in glovebox for fuelpump relay. Swap either one that is next to eachother they are the same relay. They are ground triggered you may have bad relay or ground to fuelpump.

Oct 09, 2010 | 1998 Chevrolet S-10 Pickup

2 Answers

I have replaced the fuel pump amongst a lot of other things. I can spray gas or starting fluid in the throtal body and it will run rough untill the fumes ware out. Its a 1995 ford explorer 4x4 xlt


If you hear the fuelpump operate the first 1 or 2 seconds when the key is turned to RUN position, the fuelpump is working. If you do not hear the fuelpump run, check the Inertia switch which should be in the side panel of the rear cargo area. If you have an owners manual check for the Inertia switch location.

To reset the Inertia switch, hold the button on it for 2-3 seconds. You should now hear the pump run. You may also have a fuelpump relay under the hood in one of the Powerboxes. The Powerbox may have a fusible link from the Battery. When the fusible link is OK and the Pump Relay is OK, there is a fuse in the Fuse panel. Then finally the Ignition switch will trip the Pump relay. As power flows through the wire to the fuelpump the Inertia switch can break the power connection.

So you have 5 powerpoints before the fuelpump will work. Fusible link, Pump Relay, Fuse Panel, Ignition Switch,and Inertia switch. These must all work before the fuelpump can run.

Aug 14, 2010 | 1995 Ford Explorer

2 Answers

Getting fire but fuel pump aint running


Check the fuel pump relay/fuse.

Circuit Protection The fuse box is located low on the left side of the dashboard behind a cover, or at the left side kick panel, behind a cover.
Fusible links are located in a holder next to the battery.
The fuse panel is located behind a snap-off cover in front of the driver's left knee.
Fusible links are sections of wire, with special insulation, designed to melt under electrical overload. Replacements are simply effected by removing the old unit and inserting the new into the block. Fusible links are identified by the color of their housing.

Also, your fuel pump may be bad. Check the fuse/relay first.

Dec 07, 2009 | 1992 Hyundai Excel

1 Answer

No elect. to fuel pump fuse


Have you made any other repairs to the truck lately? Starter maybe? The ignition switch has more than one source feeding it. If you lose one fusible link, you'll lose ign OR acc items. I'd check all fusible links.

Jun 02, 2009 | 1991 Chevrolet C1500

4 Answers

Chevy s10 pickup fuel pump does not work


i have a 98 chevy s10 zr2 and we changed the fuel pump and aint gettin no power to the fuel pump checked the fuses and relay under the hood no power and the gauges inside are not working other than lightin up.are there another fuse link some where

Mar 18, 2009 | 1999 Chevrolet S-10 Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...