Question about 1990 Chevrolet K2500

Open Question

1989 chevy k2500

Cant get it to stay at 2500rpm for emissions test. What would cause this? Truck runs great no other issues.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

yotaguy
  • 232 Answers

SOURCE: need Rear Brake Diagram for 1994 Chevy K2500 4x4

Here is the diagram,It is always a good idea to only disaasemble one side so you can use the other side as a reference,I also reccomend using a set od brake pliers,they will the disassembly and reassembly much easier.
0900c1528008f6a2.gif

Posted on May 30, 2009

SOURCE: My 1989 chevy 1 ton

check the anti lock solinoid to the rear brakes, it has a valve and a resiviour in it, it is in the line to the rear brakes, usually the valve or diaphram goes bad, easiest way to check it is to bypass with a piece of brake line

Posted on Oct 16, 2008

  • 15 Answers

SOURCE: 1989 Chevy K2500 - idles fine but stalls out when put into drive.

Sounds like the injectors may be bad or just really dirty. You say that the truck is only used as a plow truck, so I would assume that it sits alot. If you dont add any fuel stabilizer to the tank, the fuel will start to degrade and the will gum up your injectors. One thing you can do is to pull the air cleaner assembly off and look at the injectors while the truck is running. Look at the bottom of the injectors while it is running. The injectors shouldbe spraying fuel with a fan spray of fine mist. If you see any drips of fuel in the this fine mist, that injector is at least dirty or on its way out. I would recommend that you change your fuel filter and then get some fresh fuel and the purchase some Seafoam fuel injector cleaner from your local parts store. Dont mess around with anything else. GET SEAFOAM. If it is in a plastic bottle it is not strong enough to do anything. Seafoam is in a metal can. Dump the seafoam in and run the truck as much as you can. This will help clean out the injectors.

Posted on Jan 22, 2009

  • 16 Answers

SOURCE: How do I find out what the gear ratio is in my '99 k2500 truck

call dealer with vin number, they can tell you what it was built with.

Posted on Jul 30, 2009

  • 540 Answers

SOURCE: My 95' Chevy diesel k2500 stalls out when im Driving

I have replaced many injector driver modules on these diesels. GM has redesigned it and i have never had a replacement one fail. This is a known problem for the 6.5 diesel. Unfortunately its about a 500 dollar part from the dealer, and requires intake removal, and some very tight work space to replace.

Posted on Mar 22, 2010

Testimonial: "Thanks "

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

This is milt with the ignition fuse problem. the truck is a 1989 chevy k2500 4wd


good morning milt,so your saying its the ignition fuse that keeps blowing in the fuse block inside truck,is that right,and does it blow imediately or take sometime.

Jan 10, 2015 | Cars & Trucks

1 Answer

Hello...I have a '95 GMC K2500 Suburban with a 5.7L that failed a recent emissions test. I replaced the spark plugs, removed and cleaned the EGR...cap, rotor wires look OK...truck re-tested worst


Retarding the timing will cool the combustion which will lower the Hydrocarbon number,it will run bad but after a passed e test put the timing back to an advanced state which may help with the stumble.

Jul 22, 2017 | 1995 GMC Suburban

1 Answer

1989 f150 302 V8 fuel injected emissions problem. Installed new engine from Ford, blew SKY HIGH on low and high idle emissions. Emission numbers were 10-20x max legal limit (over 3000). Replaced the...


the O2 sensor works on one volt .5 is around the running voltage, i would refit the air hose as it will run the converter hotter at idle.

Apr 26, 2017 | 1989 Ford F 150

1 Answer

1989 Chevy K2500 350 will not restart after warmed up? I have replaced Heads, reset timing 0 TDC new plugs, coil, cap, button, module and pick up coil. Engine starts cold runs great but will not restart...


tdc is usually set at 8 degrees BTDC for an automatic and 4 BTDC for a manual transmission. This may help. Does the engine run rough at start up being set at 0TDC?

Oct 20, 2010 | 1988 Chevrolet K2500

1 Answer

1995 k2500 Chevy truck engine runs rough some of the time?


I had a similar problem @105k. I had changed the fuel filter but it was still sending all kinds of codes that were related to 2 problems. Long story short, the main problem was a bad trigger assembly in the distributor (rough running) and the other was a loose engine to body ground (engine code issue). Good luck, this worked for me, now 171k.

Nov 15, 2009 | 1995 Chevrolet K2500

1 Answer

I have a 1996 GMC K2500 power staying on to my heater fan


Hardly seems worth changing the lock cylinder, since it is not that easy.
Just be more careful turning the ignition off.
Put in an ignition indicator light on the dash if you have to.

Jul 26, 2009 | 1997 GMC Sierra K2500

1 Answer

92 chevy truck 5.7 idle revs up and down high emissions


sounds like a vacuum leak check hoses and manifold

Mar 21, 2009 | 1991 GMC K2500

1 Answer

Starting trouble


Suspect the glow plugs or timer not working proper. You could plug your truck in keep the engine warm so it starts easier. Or you could have the glow plugs tested and replaced if faulty. Your engine has 8 glowplugs and even a couple faulty glowplugs will cause problems starting. You could have injector or injection pump problems as well but harder to diagnos yourself.

Feb 26, 2009 | 1995 Chevrolet K2500

1 Answer

1989 Chevy K2500 - idles fine but stalls out when put into drive.


Sounds like the injectors may be bad or just really dirty. You say that the truck is only used as a plow truck, so I would assume that it sits alot. If you dont add any fuel stabilizer to the tank, the fuel will start to degrade and the will gum up your injectors. One thing you can do is to pull the air cleaner assembly off and look at the injectors while the truck is running. Look at the bottom of the injectors while it is running. The injectors shouldbe spraying fuel with a fan spray of fine mist. If you see any drips of fuel in the this fine mist, that injector is at least dirty or on its way out. I would recommend that you change your fuel filter and then get some fresh fuel and the purchase some Seafoam fuel injector cleaner from your local parts store. Dont mess around with anything else. GET SEAFOAM. If it is in a plastic bottle it is not strong enough to do anything. Seafoam is in a metal can. Dump the seafoam in and run the truck as much as you can. This will help clean out the injectors.

Dec 20, 2008 | 1990 Chevrolet K2500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

139 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...