Question about 2006 Toyota Sequoia Limited

2 Answers

How to disconnect the motor on a driver's side mirror

The motor on the mirror is constantly running

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

It is the switch in the mirror motor and it seems to be happening to everyone who owns a Sequoia. The fix is expensive so I figured out if I physically hold both mirrors in place while hitting the console switch to fold the mirrors inward that the mirrors would stay in place and the running motor would shut off.

Posted on Aug 05, 2012

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Toyota Master
  • 75,077 Answers

Remove the drivers door panel and the connector is right there

Posted on Feb 25, 2012

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Murphybanton
  • 2004 Answers

SOURCE: The driver's side view mirror glass is

Feel free just pull the nirror out then see if the knob is disconnected or you first check on the fuse that is meant for the power mirror.

Good luck.

Please rate this

Posted on Apr 05, 2009

  • 978 Answers

SOURCE: when start vehicle driver side

adjust the mirrors up or down might get rid of it

Posted on Apr 26, 2011

  • 3911 Answers

SOURCE: the driver's side mirror motor

if it was a bad fuse it would be dead, not stuck on. i would replace the switch before i replaced the mirror, sounds like a function of the switch is bad.

Posted on May 06, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Fuse mirror


There isn't any single fuse that supplies power to just the mirror motors.

Dec 24, 2013 | 2005 Lexus GX470

1 Answer

Memory seats adjust on there own as well as mirrors


BCM has nothing to do with this function , MMM - memory mirror module !
Memory Mirror System Operation
The MMM is capable of storing mirror position for 2 different drivers. Mirror position is determined by both horizontal and vertical position sensors in each of the power mirrors. The MMM supplies a reference voltage and a low reference to these sensors and determines mirror position through the horizontal and vertical position signal circuits.
The MMM receives power through the battery supply voltage circuit and the MIR/LOCK fuse and a constant ground source. Any time that battery voltage is disconnected and then connected from the MMM, the MMM will enter the mirror relearn mode. The mirror relearn mode can also be commanded using a scan tool. Refer to Memory Mirror Module Learn for further information.The memory switch receives power through the battery supply voltage circuit and the MIR/LOCK fuse. The MMM upon receipt of a memory switch signal input, a class 2 message from the SIC or a class 2 message from the PCM indicating that the transmission is in park, will then supply battery voltage and ground to the appropriate power mirror motors through the mirror motor control circuits to move the mirrors to the predetermined positions.

DTC B1586, B1596, B1616, or B1626
The mirror horizontal and vertical position sensors are potentiometers. The Memory Mirror Module (MMM) provides these sensors with a 5 volt reference circuit and a low reference circuit. The MMM monitors the horizontal and vertical position sensor signal circuits which change values based on mirror position. These voltage values are used to determine mirror position and can be set into memory. When the MMM receives a memory recall request, the MMM will control the power mirror to the memory position based on the horizontal and vertical position sensor signal values.

Install a scan tool.
Turn ON the ignition, with the engine OFF.
With the scan tool, observe the mirror horizontal and vertical position parameters in the Memory Mirror Module (MMM) data list.
Operate both the left and right mirrors through the full range of movements.
Does the scan tool indicate that the left and right mirror horizontal and vertical position parameters are within the specified range?

Memory Seat System Components
The memory seat system consists of the following components:
• Power seat switch assembly
• Memory recall switch assembly
• Horizontal adjuster motor
• Front vertical adjuster motor
• Rear vertical adjuster motor
• Recline adjuster motor
• Memory seat module
• Memory mirror module
• SEAT 25A circuit breaker
• MIR/LOCK 3A fuse

Your best bet , take it to a qualified repair shop !

May 23, 2017 | 2002 Cadillac Escalade

2 Answers

Drivers side seat and mirror don't work


I have a 2006 land rover lr3 hse my driver seat and mirrors and cooler in the center stopped working all fusses look ok what could be the problem please help thank you

Oct 31, 2012 | Land Rover Cars & Trucks

1 Answer

2002 Mountaineer. How do you change the light bulb at the bottom of the driver side rear view mirror. Dan


SECTION 501-09: Rear View Mirrors 2002 Explorer/Mountaineer Workshop Manual REMOVAL AND INSTALLATION Exterior Mirror Glass Removal
NOTE: Exterior mirror glass is serviceable only on vehicles built after July of 2001.

NOTE: Passenger side exterior mirror shown, driver side exterior mirror similar.
All mirrors
  1. Position the glass in the full up position.
  1. Locate the notch at the bottom of the exterior mirror glass.
ed6be7c.gif
  1. Release the exterior mirror glass.
    1. Insert a long flat-bladed screwdriver in the notch.
    1. Push the screwdriver into the notch until the glass is released.
Heated mirrors
  1. Position aside the exterior mirror glass.
  1. Disconnect the electrical connectors.
All mirrors
  1. Remove the exterior mirror glass (17K707) passenger side or (17T675) driver side.
Installation
Heated mirrors
  1. Connect the electrical connectors.
All mirrors
  1. Position the exterior mirror glass on the exterior mirror motor.
  1. Place a hand against the back of the exterior mirror housing and a hand flat against the exterior mirror glass. Press the glass in place until fully seated.

Dec 26, 2009 | 2002 Mercury Mountaineer

1 Answer

Mirror glass replacement on drivers side


i don't have aviator. here's explorer, should be the same.

You will see a small rectangle where the screwdriver goes in. You are pryingtowards glass. The retention is about a 3 inch rectangle that has a lip around it that snaps onto a rectangle on the mirror body.

SECTION 501-09: Rear View Mirrors 2002 Explorer/Mountaineer Workshop Manual
REMOVAL AND INSTALLATION Exterior Mirror Glass Removal
NOTE: Exterior mirror glass is serviceable only on vehicles built after July of 2001.
NOTE: Passenger side exterior mirror shown, driver side exterior mirror similar.
All mirrors
  1. Position the glass in the full up position.
  1. Locate the notch at the bottom of the exterior mirror glass.
  1. Release the exterior mirror glass.
    1. Insert a long flat-bladed screwdriver in the notch.
    1. Push the screwdriver into the notch until the glass is released. (and pull screwdriver towards glass)
Heated mirrors
  1. Position aside the exterior mirror glass.
  1. Disconnect the electrical connectors.
All mirrors
  1. Remove the exterior mirror glass (17K707) passenger side or (17T675) driver side.
Installation
Heated mirrors
  1. Connect the electrical connectors.
All mirrors
  1. Position the exterior mirror glass on the exterior mirror motor.
  1. Place a hand against the back of the exterior mirror housing and a hand flat against the exterior mirror glass. Press the glass in place until fully seated.

Apr 18, 2009 | 2003 Lincoln Aviator

1 Answer

99 explorer drivers side mirror vibrates


are you trting to tighten the mirror glass or the mirror where it attaches to the body? I don't think glass is removable in 99. Only can try to press on glass to seat if unseated. not too hard.

  1. Remove the front door trim panel; refer to Section 501-05 .
  2. go to car-part.com for a used mirror. Page with * is cheapest seller.
  1. Remove the speaker.
    1. Remove the screws.
    1. Disconnect the electrical connector.
    1. Remove the speaker.
  1. Remove the outside rear view mirror (17682).
    1. Disconnect the power mirror wiring clips.
    1. Remove the outside rear view mirror nuts.
    1. Remove the outside rear view mirror.
      • Feed the power mirror wiring through the opening in the front door (20124).
------------------------------------------------------
f9d70e9.gif
----------------------------
SECTION 501-09: Rear View Mirrors 2001 Explorer/Mountaineer Workshop Manual
REMOVAL AND INSTALLATION Exterior Mirror Glass, 2001 model Removal
NOTE: Exterior mirror glass is serviceable only on vehicles built after July of 2001.
NOTE: Passenger side exterior mirror shown, driver side exterior mirror similar.
All mirrors
  1. Position the glass in the full up position.
  1. Locate the notch at the bottom of the exterior mirror glass.
  1. Release the exterior mirror glass.
    1. Insert a long flat-bladed screwdriver in the notch.
    1. Push the screwdriver into the notch until the glass is released.
Heated mirrors
  1. Position aside the exterior mirror glass.
  1. Disconnect the electrical connectors.
All mirrors
  1. Remove the exterior mirror glass (17K707) passenger side or (17T675) driver side.
Installation
Heated mirrors
  1. Connect the electrical connectors.
All mirrors
  1. Position the exterior mirror glass on the exterior mirror motor.
  1. Place a hand against the back of the exterior mirror housing and a hand flat against the exterior mirror glass. Press the glass in place until fully seated.
4d9527f.gif

Apr 12, 2009 | 1999 Ford Explorer

1 Answer

The driver's side view mirror glass is disconnected from the power motor mechanism. How do I pop the mirror out and reattached it to the control. The mirror is not broken, just will not adjust with the...


Feel free just pull the nirror out then see if the knob is disconnected or you first check on the fuse that is meant for the power mirror.

Good luck.

Please rate this

Apr 05, 2009 | 2002 Toyota Camry

3 Answers

Replacing the Mirror Light - driver's door


I assume your question is how to replace the bulb in the side mirror. Can you please tell us the make and model of the car.?
Thanks,

Jan 24, 2009 | 2002 Volvo S80

1 Answer

Driver side mirror


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. You can then disconnect the cable running form the mirror to the control. Then you can access the bolts that secure the mirror onto the door

Nov 08, 2008 | 2006 Chevrolet Cavalier

1 Answer

Side Mirrors will adjust side to side but not up and down.


There are two tiny motors in each mirror. one for up/down. One for side to side. They have jack screws (plastic) that fit into the motors.

You can manually put your hands on either side of the mirror and force adjust it. If you hear a ratcheting sound, the jack screws are OK. Then repeat with hands on top and bottom.

If you hear ratcheting and mirror stays where you stop it, that means one of the motors is bad. The motor assembly is available as a separate part.

-------------------------------------------------------------------------------------
Mirror Motor—Crown Victoria, Grand Marquis
Removal and Installation
  1. Disconnect battery ground cable. Refer to Section 14-01 .
  1. Remove outside Rear View Mirror Glass as outlined.
  1. Remove Outside Rear View Mirror as outlined.
  1. Remove two screws from outside rear view mirror motor.
  1. Remove outside rear view mirror housing from outside rear view mirror base.
  1. Disconnect connector and remove outside rear view mirror motor from mirror housing.
  1. To install, reverse Removal procedure.
1a865db.gif
Might be cheaper to buy used irror at car-part.com. Look for * to find page with cheapest part. Or, EBay. Good luck

Aug 11, 2008 | 1996 Ford Crown Victoria

Not finding what you are looking for?
2006 Toyota Sequoia Limited Logo

667 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...