Question about 2003 Ford Crown Victoria

Open Question

2003 crown victoria speedometer not working - 2003 Ford Crown Victoria

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
mrgreenz
  • 962 Answers

SOURCE: my speedometers does not work

Check the speed sensor at the tranny.Get a trouble code at any autoparts store.

Posted on Feb 06, 2009

Ad
97crownvic
  • 28 Answers

SOURCE: crown victoria window motor replacement

remove the door panel. be very careful and make sure you get all the screws out. Should be maybe 2 on the bottom half of the door, and 2 on the top half. one is right by the handle, which is the one i forgot the first time i took my door pannel off. carefully pull the panel upward, and outward at the same time. Once the panel is off, disconnect the controls, and remove the light from the panel. Remove the plastic cover very carefully, it will tear, just keeps noise, and air, and the elements out.
There will be 3 screws, they are torx bolts, once you pull those 3 out. They are located middle of the door towards the right side. The motor will drop down a little bit. disconnect the wires for the motor, and wiggle the motor off of the regulator. the crown vics have a decent size hole to get into the door panel, you can also remove the speaker if that would help you do it. other than that, it just lining up the new motor into the car, pushing it into the regulator, and putting the 3 bolts in, make sure they are snug, and not cross threaded. put everything back together, and your set.

Posted on Mar 19, 2009

  • 104 Answers

SOURCE: 2003 Ford Crown Victoria misfires when

I HAVE HAD THE SAME PROBLEM ON SEVERAL CROWN VICS I HAVE WORKED ON ,& SOME OF THEM A SET OF PLUGS STOPPED IT,AND SOME OF THEM HAD TO HAVE 1 OR MORE COIL PACKS REPLACED, BUT THE PROBLEM THAT I FOUND THAT IF PLUGS & ALL COIL PACKS HAD BEEN REPLACED,AND IT WAS STILL IN THE IGNITION, IS THE WIRES GOING INTO THE PLUG ON THE COILPACK UNDER THE INTAKE TUBE, IF YOU REMOVE THE INTAKE TUBE,LOOK CLOSE AT THE WIRES FOR ANY BARE SPOTS,& LOOK AT THE BOTTOM OF THE INTAKR TUBE IF YOU CAN SEE WHERE IT HAS RUBBED IT,IT IS ALMOST A GIVEN THERE IS A BARE SPOT OR CRACKED INSOLATION ON THE WIRE, ENOUGH TO CAUSE A MISFIRE, (FYI) IT TOOK ME MANY TIMES OF INSPECTING BEFORE I LOOKED CLOSE ENOUGH TO SEE THE BARE SPOTS, BUT ALL YOU HAVE TO DO IS STRIP THE HARD PLASTIC AROUND THE WIRES BACK ENOUGH TILL YOU SEE GOOD CLEAN LOOKING WIRE,THEN SEPERATE THE WIRES AND IF YOU HAVE LIQUID ELECTICAL TAPE USE THAT AND THEN TAPE THEM WITH ROLL ELECTRICAL TAPE ,BUT IF YOU TAPE THEM UP GOOD SO WHEN THE WIRE IS BENT ENOUGH FOR THE INTAKE TUBE TO CLEAR ,& YOU CANNOT SEE THE WIRES GOING IN TO THE PLUG WITH A ROLL OF ELECTRICAL TAPE THAT WILL WORK TOO, I HOPE THIS TRICK WILL WORK AS GOOD FOR YOU AS HAS ME ON DOZENS OF CROWN VICS, ESPECIALLY P71 POLICE CARS.

Posted on Dec 05, 2009

  • 104 Answers

SOURCE: on a 2003 ford crown victoria. the head light does

it is more than likely the lcm (lighting control module) under the dash above the gas pedal two 7mm screws and two plugs that is the most common problem

Posted on Dec 09, 2009

AutoDoc
  • 169 Answers

SOURCE: 2002 crown victoria speedometer not working

Hi Sr8688,
My name is Chuck and I'd like to help you figure this out. There are a couple of different things that can cause the situation you are experiencing. Check fuse #8 in the under-hood fuse box. If it checks ok, you can either use a scanner to monitor the input from the vehicle speed sensor or you can physically check it with a digital volt/ohm meter that can read a/c voltage. If you want to go further,drop me a line and let me know what equipment you are going to use and I will send you the next steps. Thanks,Chuck

Posted on Feb 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can an engine be rebuilt in a 2003 crown victoria police car


Yes it can, there are many parts around for a rebuild, even upgrade some parts, you can also rebuild your transmission too, even change gears. But you can also find used low mile engines around as well as a replacement , These are modular engines , Grand Marquis will work as well

Oct 04, 2014 | 2003 Ford Crown Victoria

1 Answer

How do you replace a 1994 crown victoria's speedometer cable?


No cable, it's electric. Run by a sensor on rear of transmission.

Dec 15, 2012 | 1994 Ford Crown Victoria

1 Answer

1992 crown victoria speedometer works odometer does not work .


This is an internal issue and the speedometer must be removed and repaired. There are people who still do this and can rebuild your old unit. Look in your area or there may be places to ship it to. Local salavage yards may have it if down time is an issue. Be sure to save the receipt in the car so that actuall mileage can be verified.

Nov 08, 2010 | 1992 Ford Crown Victoria

1 Answer

I recently purchased a 2001 Crown Victoria P-71. It came woth a bullet hole through the speedometer and windshield. I have had the windshield replaced, but need help replacing the speedometer. How do I...


open the screws of cover of speedometer and pull it and release the locks then open the screws of speedometer and ungrip the cables. simple thing do not b afraid of opening it nothing will happen.

Aug 01, 2010 | 1991 Ford LTD Crown Victoria

1 Answer

Ford crown victoria


you must replace the multi fuction switch! also known as the turn signal switch! its common on ford crown vic!

Mar 06, 2010 | 2001 Ford Crown Victoria

1 Answer

ODOMETER CEASED WORKING ABOUT A MONTH AGO (66,667) MILES SPEEDOMETER IS W0RKING FINE. WHAT REPAIR WORK DO I NEED.? DOUG 1992 CROWN VICTORIA


U will need to pull the speedo head out and send it in for repair, there are no parts availiable to the consumer, only authorized Ford repair stations, that is not the dealer, check the internet, I use DNA speedometers.com

Mar 25, 2009 | 1992 Ford Crown Victoria

1 Answer

My speedometers does not work


Check the speed sensor at the tranny.Get a trouble code at any autoparts store.

Feb 06, 2009 | 1993 Ford Crown Victoria

Not finding what you are looking for?
2003 Ford Crown Victoria Logo

Related Topics:

347 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

fordexpert

Level 3 Expert

5572 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...