Question about 1994 Toyota Corolla

Open Question

Is it accurate when u jump the terminals - 1994 Toyota Corolla

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Where-is-the-battery-in-a-gmc-terrain Problem


It is behind the left headlamp under the Powertrain Control Module (PCM). You have to partially remove the front bumper fascia and the PCM to get at it. (see diagram)


dttech_185.gif

Sep 02, 2011 | GMC Terrain Cars & Trucks

2 Answers

Can i jump start my friends focus with my mercedes c230 2006? thank you


You can jump start any car provided the jump start cables have a surge protecter.

Aug 08, 2011 | 2006 Mercedes-Benz CL-Class

1 Answer

How to jump start my 2005 Pontiac Montana?


Using jumper cables :
1. Connect one red clamp to the positive terminal (+) of running car's battery and the other end red clamp to the positive terminal (+) of the dead car's battery .
2. Connect one black clamp to the negative terminal (-) of running car's battery and the other end black clamp to the negative terminal (-) of the dead car's battery.
Basically... (+) to (+)...and... (-) to (-)
3. Crank up the car needing the jump.
4. Once car is jumped and running...remove clamps in reverse order.

Using battery pack: Connect in the same fashion as above.

Jul 31, 2011 | 2005 Pontiac Montana

2 Answers

Car will not crank battery good


What type of response are you getting when you turn the ignition. Is it trying to roll over or are you only geting a click noise and no engine sound? I would say that it is most likely the starter, but some more info woult help me be accurate in seeing what is wrong. Thanks!!

Sep 21, 2010 | 1994 Pontiac Bonneville

1 Answer

My 2004 mini cooper will not take a jump. The car was running fine. I ran into a store and 3 minutes later attempted to start it and NOTHING. So I attempted to jump it, Mini will not take a jump. Any idea...


If you are trying to jump from the factory "Jump start" terminals and nothing is working, You should suspect your cable to battery connections. Remove the battery cables from the battery and clean the battery posts and the cable terminals. (Auto parts stores sell a very inexpensive tool to do this) Reinstall and tighten the terminals.

Jul 18, 2010 | 2004 Mini Cooper

1 Answer

99 cavalier - the fuel gauge doesnt read accurately and it jumps


Possibly a bad ground wire at the sender on the tank,

Check for that first before tearing into the dash to replace the guage.

Mar 31, 2010 | 1999 Chevrolet Cavalier

1 Answer

Please tell me where are the positive and negetive ends of the battery for a jump start, my batttery is dead Dr.S.V.Anand


If you can locate the battery, telling the positive from the negative terminal easy.

Inspect the terminals closely; the positive terminal has a 'plus' (+) sign near it. This terminal is also larger than the other (usually).

Similarly the negative terminal has a 'minus' (-) near it.

Also visit this page for more information on jump starting.

Dec 22, 2009 | 2002 Dodge Intrepid

1 Answer

Park brake light flashes 10 times. For 1989 Chevy 1500 pickup. What does this mean?


This truck probably has Rear Wheel Anti-Lock (RWAL) brakes. There is a small black module near master cylinder that is the brain for this system. There are ways to check for diagnostic trouble codes in this system. Once you have any codes set, diagnosis can be fairly simple. PROCEDURE:
Diagnostic Trouble Codes (DTC) 's can be displayed by jumping terminals "A" and "H" of the Data Link Connector and observing the flashing of the "BRAKE" warning light. This should only be done when the brake lamp is "ON".
The terminals must be jumped for about 20 seconds before the code will begin to flash. Count the number of short flashes starting from the long flash. Include the long flash as a count. Sometimes the first count sequence will be short. However, subsequent flashes will be accurate. If there is more than one failure, only the first recognized code will be retained and flashed.

NOTES:
DTC's 6, 9 and 10 will only turn the "BRAKE" lamp on while the fault exists. These are soft codes faults and can only be read with the Tech 1 scan tool.
Do not jump terminals "A" to "H" if the "BRAKE" lamp is not on. Jumping the terminals with the "BRAKE" lamp off will set a false DTC 9. This will turn the "BRAKE" lamp on and disable the antilock system.

d09165f.gif
  • 1, 11, & 12 ECU Malfunction
  • 2 Open Isolation Valve or Malfunctioning ECU
  • 3 Open Dump Valve or ECU Malfunction
  • 4 Grounded Antilock Valve Reset Switch
  • 5 Eccessive Actuations of the Dump Valve
  • 6 Erratic Speed Signal
  • 7 Shorted Isolation Valve or Faulty ECU
  • 8 Shorted Dump Valve or Faulty ECU
  • 9 Open Circuit to Speed Signal
  • 10 Brake Lamp Switch Circuit
  • 13, 14 and 15 ECU Malfunction
  • Sep 29, 2009 | 1989 Chevrolet C1500

    1 Answer

    Jump Start Topside terminal Location735IL


    There is a positive jumping point underneath the hood on the passenger side.

    Feb 26, 2009 | 1988 BMW 7 Series

    2 Answers

    How do you jump start the battery on a 2004 porsche cayenne ?


    it should have one its only covered with plastic cover on it and the proper way to jump it is positive to positive then negative to source and just connect to a good ground the other vehicle..

    Dec 23, 2008 | 2005 Porsche Cayenne

    Not finding what you are looking for?
    1994 Toyota Corolla Logo

    Related Topics:

    11 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Toyota Experts

    yadayada
    yadayada

    Level 3 Expert

    77202 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22265 Answers

    Jeffrey Turcotte
    Jeffrey Turcotte

    Level 3 Expert

    8743 Answers

    Are you a Toyota Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...