Question about Cars & Trucks

Open Question

Replace front windscreen wiper motor on a mazda E2200 VAN

I am trying to replace front windscreen wiper motor on a mazda E2200 VAN and trying to remove dash board and have removed all the screws that i can see but it will still not come off,i have also removed three bolts two at side one in the middle .need advice

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Windscreen wiper not working

check the switch on the steering usualy it becomes faulty after a while and also your window washers could be blocked but try turning it on if you do not hear a buzzing sound the motors needs to be replaced.

Posted on May 21, 2008

emissionwiz
  • 75117 Answers

SOURCE: why my windscreen wipers on my polo stopping up on the windscreen

Your wiper has what is called a parking circuit, this sets the wipers to the bottom of the windshield when the power or ground is turned off, in order to fix this issue u will need to replace that part, it may be part of the wiper motor, not for sure on VW's.

Posted on Feb 21, 2009

  • 1 Answer

SOURCE: Windshield wiper arm disconnected

My dad helped me solve this problem on my truck...

They simply pry off. He put down a towel to protect the cowl grill, took a hammer (using the split end) and pried them right off.

There was no mechanism holding them on, when we were done working under the grill, we used the same towel, but the other side of the hammer to stick 'em back on.

Posted on Mar 30, 2009

  • 13 Answers

SOURCE: how do i remove and replace the driver's side mirror?

If the metal pivot arm is not broken you can just replace the glass and plastic housing. To remove the glass you tilt the glass down towards the floor and use a wide plastic or wood bladed object to prise from behind, the glass should pop off from its clips. Remember to catch it if its not damaged. To remove the housing once the glass is out you need to look underneath the mirror unit, there you will find a small plastic bung, gently prise it out and then use a long small flat bladed screwdriver straight up inside the hole and lever towards the front of the car whilst lifting straight up on the plastic housing, this should then lift off. To replace just slot the new housing on and click into place then fit the glass back, remember to connect the wires first if it is a heated glass.
If the metal pivot arm is broken then you will find the remaining screws behind the plastic trim inside the vehicle.

Posted on Apr 10, 2009

  • 34 Answers

SOURCE: windscreen wipers banging on hood

just turn of the wiper switch turn off the key 30 sec later, move the wiper arm to the park position, then remove the caps plastic caps at the start off the wiper arm ( if fitted) and then tigthen the nut there and that should fi it

Posted on May 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1995 GMC Vandura 2500 custom van. i need to know location and how to replace wiper motor


Make sure that's what you need because it's not a fun job.The wiper motor is under the dash above the gas pedal.Way up under the dash.Partial and/or full dash removal may be necessary.It depends on your skill level and determination! One heck of a great van to own!

Apr 28, 2017 | GMC Cars & Trucks

1 Answer

How to replace windscreen washers?


Remove facia. Look for screws hidden under rubber strip which seals hood to cowl. Remove screws and pull away from windshield. Some require removing wiper arms first.

Jul 01, 2014 | 2008 Mazda 6 2.0

1 Answer

Can you please give me instructions on replacing the wiper motor pulse board module on my 95 Chevy Van G20?


This is a very simple procedure and will save you lots of money by replacing it yourself! A common replacement item on GM vehicles, it should be readily available at your local auto parts retailer and should take no more than a half-hour with just a couple of tools.


• Turn the ignition key to the OFF position.
• Remove the Connector Position Assurance (CPA) and disconnect the wiper motor electrical connector.
atye.gif
• Remove the three screws that secure the cover to the wiper motor and remove the cover.
• Inspect for sealant on the inside of the cover and then discard the cover and screws. Important: If sealant was found on the old cover, it will be necessary to remove any old sealant from the motor housing in Step 6.
• Carefully remove the module (circuit board) from the wiper motor by lifting up on the end of the module electrical connector.
• If necessary, remove any old sealant from the wiper motor housing (refer to Step 4). Notice: When handling the new module in the next step, be careful not to damage or band the electrical contacts on the bottom side of the module.
• Install the module into the wiper motor housing, making sure that the module is fully seated. When fully seated, the edges of the module circuit board will be flush (even) with the motor housing along all sides.
atye_0.gif
• Carefully apply a bead of silicone sealant, P/N 12345739 (or GE-162 sealant or equivalent) in the groove of the NEW cover (Figure 2). Remove any excess sealant that is outside of the groove. Important: Only apply enough sealant to fill the groove in the cover.
Install the new cover on the wiper motor housing and install the three new screws.
• Tighten the screws to 2.6 N·m (23 lb in).
• Reconnect the wiper motor electrical connector to the wiper motor assembly and install the CPA.
• Turn the ignition key to the ON position and check the wiper system for proper operation (delay/low/high/etc.).



May 04, 2011 | Chevrolet G20 Cars & Trucks

1 Answer

My front wipers on A4 audi have been slow eversince windscreen was replace a couple of months ago. Obviously this time of year they have been little used but this morning have little power and stop dead on...


First you must diagnose why windscreen wipers going slow and/or stopping.
In order to find out the cause of wipers stopping you can try follows: 1. Carefully extract the wiper arms from their axles (two pieces). In some cases you need to use an extracting tool. Heed of the windscreen !!! 2. Disassemble the plastic covers from the bottom of the windscreen. 3. With the bonnet up you can start the engine, (transmission in "N" or "P" position and parking brake on). Now you must switch on the control lever of the wipers, and go to the engine compartment. If the wiper motor runs let the wiper motor running for a few minutes and switch off. Go to the step 4. If the wiper motor do not runs you must check first the electrical feeding of the motor. It is necessary to unscrew three bolts of the mechanism and disconnect the electrical coupling (difficult assurance). If the electrical feeding is OK you must replace the motor - steps 5, 6, 7. If not you must check electrical connections, the control switch of wipers and electric cables. 4. Now you must check the two bearings of wiper mechanism with your hand. In the most cases the left bearing is out of order (is very hot). This is the most encounter fault of the wipers running at Audi. 5. For have enough space to manipulation the wiper motor together with their mechanism you must extract the plastic cover of the engine computer box, and extract also the box screws. Then you can move slowly the engine computer box, just for a few milimeters. 6. You must disconnect the electrical coupling of the motor (difficult assurance), unscrew three bolts of the mechanism and extract together with the motor. You must move them slowly between windscreen and engine computer box until the wiper motor go out together with the mechanism. This is the most difficult operation! 7. Now you can repair the bearings, replace entire wiper mechanism or replace the wiper motor. It is not very simply, but it works.
Heed of the windscreen !!!
Refit all in reverse order.

Sep 22, 2010 | Audi A4 Cars & Trucks

1 Answer

How do you remove the heater motor from a merc 300d 1993


The heater motor is beneath the windscreen wiper. 1) remove the rubber edge strip that runs across the engine bay separating the the engine from the battery on one side and the brake servo on the other. 2) at the back of the engine bay the middle panel is held on by large plastic finger tightened nuts, remove these and lift out the panel. 3) loosen the rubber strip to the base of the windscreen and surrounding the windscreen wiper mechanism. 4) remove the screws that holds the plastic guttering along the base of the screen. 5) be aware of clip underneath at the inner part of the guttering where it meets the surround to the central wiper unit cowl. 6) remove the top four screws and two on the underside of the cowl and lift away. Undo the 4 bolts (10mm) that hold the wiper motor frame and remove the clip that holds it in the middle to the bulk head lower down. Disconnect the motor and lift away. 7) you now have access to the heater motor, it held by three screws. Disconnect the electrical connector and lift it out. On my own car I had a situation where the heater motor would come on or work faster as I turned left but went off or slowed right down when I turned right. Both the carbon brushes has become fixed in their passageways and the slight shift of the motor spindle in the bearings either made or broke the electrical contact between the now fixed brushes and the armature. A simple removal of the brushes to clean and lubricate has ensured no further incidence.

Jul 15, 2010 | 1993 Mercedes-Benz Mercedes Benz 300 Class

1 Answer

Wiper motor


First you must diagnose why windscreen wipers going slow and/or stopping.
In order to find out the cause of wipers stopping you can try follows: 1. Carefully extract the wiper arms from their axles (two pieces). In some cases you need to use an extracting tool. Heed of the windscreen !!! 2. Disassemble the plastic covers from the bottom of the windscreen. 3. With the bonnet up you can start the engine, (transmission in "N" or "P" position and parking brake on). Now you must switch on the control lever of the wipers, and go to the engine compartment. If the wiper motor runs let the wiper motor running for a few minutes and switch off. Go to the step 4. If the wiper motor do not runs you must check first the electrical feeding of the motor. It is necessary to unscrew three bolts of the mechanism and disconnect the electrical coupling (difficult assurance). If the electrical feeding is OK you must replace the motor - steps 5, 6, 7. If not you must check electrical connections, the control switch of wipers and electric cables. 4. Now you must check the two bearings of wiper mechanism with your hand. In the most cases the left bearing is out of order (is very hot). This is the most encounter fault of the wipers running at Audi. 5. For have enough space to manipulation the wiper motor together with their mechanism you must extract the plastic cover of the engine computer box, and extract also the box screws. Then you can move slowly the engine computer box, just for a few milimeters. 6. You must disconnect the electrical coupling of the motor (difficult assurance), unscrew three bolts of the mechanism and extract together with the motor. You must move them slowly between windscreen and engine computer box until the wiper motor go out together with the mechanism. This is the most difficult operation! 7. Now you can repair the bearings, replace entire wiper mechanism or replace the wiper motor. It is not very simply, but it works.
Heed of the windscreen !!!
Refit all in reverse order.



Jun 01, 2010 | 2000 Audi A6

2 Answers

Mazda 1997 E2000 VAN, WIPERS WORKING only dead slow, replaced motor, switch & control


hi fixya pls i need a mazda e2200 van to buy and my name is fitzgerald from west africa ghana . and email address is kengfiz@co.uk

Dec 14, 2008 | 1999 Mazda B-Series

1 Answer

Winshield wipers stick


Had the same problem on my '92 and 97. on the wiper motor there is a front cover held by a center screw... remove the cover there should be a small computer circuit board... disconect and replace... the cards are known to fail and a new replacement part, not a used one. they all fail on the older models.. new one has corrected the issue with the card... hope this works;;

Dec 08, 2008 | 1994 Chevrolet Astro

1 Answer

Eratic front wiper motor on a 1996 A4


It is not very difficult to replace the wiper motor, but first you must diagnose this problem. In order to find out the cause of wipers stopping you can try follows:
1. Carefully extract the wiper arms from their axles (two pieces). In some cases you need to use an extracting tool. Heed of the windscreen !!!
2. Disassemble the plastic covers from the bottom of the windscreen.
3. With the bonnet up you can start the engine, (transmission in "N" or "P" position and parking brake on). Now you must switch on the control lever of the wipers, and go to the engine compartment. If the wiper motor runs let the wiper motor running for a few minutes and switch off. Go to the step 4. If the wiper motor do not runs you must check first the electrical feeding of the motor. It is necessary to unscrew three bolts of the mechanism and disconnect the electrical coupling (difficult assurance). If the electrical feeding is OK you must replace the motor - steps 5, 6, 7. If not you must check electrical connections, the control switch of wipers and electric cables.
4. Now you must check the two bearings of wiper mechanism with your hand. In the most cases the left bearing is out of order (is very hot). This is the most encounter fault of the wipers running at Audi.
5. For have enough space to manipulation the wiper motor together with their mechanism you must extract the plastic cover of the engine computer box, and extract also the box screws. Then you can move slowly the engine computer box, just for a few milimeters.
6. You must disconnect the electrical coupling of the motor (difficult assurance), unscrew three bolts of the mechanism and extract together with the motor. You must move them slowly between windscreen and engine computer box until the wiper motor go out together with the mechanism. This is the most difficult operation!
7. Now you can repair the bearings, replace entire wiper mechanism or replace the wiper motor.
It is not very simply, but it works.
Heed of the windscreen !!!
Refit in reverse order.
Success!


Nov 14, 2008 | 2004 Audi A4

2 Answers

Wiper motor replacement


Im looking for a way to get at the rear wiper motor.How do you get the panaling off

Jun 20, 2008 | 1997 Dodge Caravan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...