Question about Cars & Trucks

Open Question

1998 infinti i30 low beams wont work but high beams do

I replaced only one light bulb in my 1998 infiniti i30 and i left the other one the way it was and ever sense i did that my low beams will not work at all but my high beams do and now only my left side is working. stressing out A LOT!

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 13 Answers

SOURCE: Timing chain on 2000 Infiniti I30

timming chain not belt . its a really big job i suggest the dealer.to much work and u need a lift to do the job!

Posted on Jun 22, 2008

SOURCE: oxygen sensors, knock sensor

it under intake goood luck

Posted on Sep 13, 2008

SOURCE: LOW BEAM LIGHTS

Hi Rich Million,

Check the bulbs for the low beam problem and if they're ok, check the fuses under the bonnet (hood) which are found in the fuse box. If you've already checked those, go to the fuse box inside the vehicle.

Still no luck....remember that there are fuses and relays inside the cabin behind the kick panel.....You may find that there is a problem with the main fuse box.....If you drive over rough terrain, check the connections under the main fuse box....even if your roads are all smooth, it's still worth checking.....

Regards Johngee10

Posted on Sep 25, 2008

  • 104 Answers

SOURCE: Right headlamp doesn't work on low beam only

in this case make sure you have voltage going to the low beam lights. 12 volts. you need a volt meter. if you do not have volatge you have to check and make sure power is going through the fuse. a bad fuse will be broke, but you can have a good fuse with no power going through it. if you have power going through the fuse you have a wiring open somewhere between fuse and whatever is between the headlight connecter.

plz check and get back i will keep checking on here on and off.

Michael
ASE certified
PLZ rate

Posted on Feb 09, 2009

  • 1054 Answers

SOURCE: Left low beam headlight on Chrysler 2003 T&C wont work while engine is on

Ill guarantee you have an electrical short on the left side of the headlight switch,circuit.From here its immpossible for me to go any further.Good Luck.,Get A Wiring diagram.

Posted on Apr 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What would cause the low beam headlight not to work when all other lights work?


If you have standard halogen bulbs:

  1. Burned out light bulb; or
  2. Fried wires between the dashboard wiring harness and the headlight bulb connectors; or
  3. Fried headlight bulb connectors.
If you have HEI emitters:
  • Failed ballast.

May 11, 2015 | 2002 Mercury Grand Marquis

4 Answers

I have a 2006 civic SI. DRL indicator is on, driver side low and high beam ok. Passenger side low beam ok but DRL and hi beam not working. Any help is appreciated.


When either the high or low beam light is out in either side, DRL (daytime running lights) indicator will come on. When one bulb goes out, that's a clue the opposite bulb will burn out soon, so its best to replace both bulbs. If it was a fuse issue, both left and right side would be out. If driver side is OK but passenger side is not, then its a bulb issue. A 2006 Honda civic takes 9006 (HB4) low beam bulbs and 9005 (HB3) high beam bulbs. Cheapest is online from Walmart site-2-store. After procuring, wear latex, vinyl, or ANY gloves to keep your (corrosive) oil skin from coming in contact with headlight glass bulbs. Your skin oil will chemically react and cause shorter life span on glass bulbs. Instruction don't tell you this, so you handle with your hands, then need to replace bulbs 3 years later instead of 5 years (or more) in the future. With gloves on, pop the hood and look behind each headlight. Turn counter clockwise to unlock headlight bulb holders. Its a quarter to half turn to unlock bulb holder lock. Replace one bulb at a time so you don't confuse high beam from low beam. The wire has a tab you need to lift to pull out & disconnect wire connector. You might need a slim narrow-**** (NOT phillips) screwdriver to lift the tab; or use your house key. Snap the wire connector to the new bulb, then twist into headlight housing to secure bulb holders, then move on to the next bulb to repeat the procedure. Pict below, 9005 high beam is on the left, 9006 low beam is on the right. Handle by grasping the plastic base, not the glass bulbs. The raised potrusion on the bottom center is where the tab locks onto wire connector. Replace all 4 bulbs now, but in the future, its likely the low beam will wear out before the high beam. In the future, replace only the pair, not all 4. The factory installs inferior bulbs that go out sooner, hoping you'll take to dealership and they ******** you with higher parts-n-labor fees. As opposed to Walmart online site-2-store, it would cost you AT LEAST triple in parts & labor from dealership to replace all 4 headlight bulbs :-(
45d1f6ac-2983-42b9-a46c-30ef441b89e7.jpg

Nov 29, 2013 | 2006 Honda Civic

1 Answer

No ground signal on right low beam chevrolet cavalier 1998


The bulbs are grounded to the body, so if one ground wire is dead I would expect to find a break in the wire or at the connector. You should be able to splice into the wire and run a new one to a grounding bolt.

Aug 26, 2012 | 1998 Chevrolet Cavalier

1 Answer

My light problem is i have low beam on right side no low on left side i turn highs on and right side goes out and high on left turns on then when back to lows beams and i pull turn signal to flash high...


If you have separate bulbs for the low and high beams(4 light system), if you pull the turn signal and hold it, all 4 lights will stay on until you release the turn signal. You need to replace the bright bulb on the right side and the low bulb on the left side. If your headlights only have one bulb on each side, then you will have to replace both of them to get everything to work.

Jan 04, 2011 | 2000 Ford Mustang

1 Answer

Low beam works but not high beams on 1998 ford exploer


the element in your halogen bulb for high beam has blown, replace the bulb

Jun 11, 2010 | 1998 Ford Explorer

1 Answer

98 caviler low beam


98 caviler high beam left side dosent work canged bulb checked fuse and all good

Feb 06, 2010 | 1998 Chevrolet Cavalier

1 Answer

Low beam headlamps wont turn on change bulbs and checked fuses and still wont come on.


did you check for a relay in your fuse panel? there should be a relay that controls your low beams and one for your high beams. check for that and then if high beams are working swap it with low beam relay. if your problem switches to low beams working and high beams not working replace the bad relay.

Jan 26, 2010 | 1998 Ford Explorer

1 Answer

2002 pathfinder, the left headlight bulb does not work when the


Sounds like you need a bulb,the daytime running lights send power to the high beam wire so they look like low beam lights are on but really they are high beam lights running on low voltage.

Nov 19, 2009 | 2002 Nissan Pathfinder

1 Answer

Daytime running light working fine but can not switch on the head light? 1998.


Pull the head light switch and check it for out put.Do you have high beams?Check the low beam headlight bulbs.If you have high beams,and low beam bulbs are good,replace the dimmer switch.

Nov 10, 2009 | 1998 Ford Escort

1 Answer

My left headlight highbeam light works and the lowbeam don't why


the filament on the low beam burnt out. but the high beam didn't. You have a filament for each. 1 for high beam and 1 for low beam in the same light bulb. You need a new head light.

Sep 07, 2009 | 1998 Ford Windstar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...