Question about 1998 Jeep Cherokee

Open Question

Replace blinker light 1998 jeep cherokee - 1998 Jeep Cherokee

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1779 Answers

SOURCE: Blinkers not working

Did you check the bulbs? If one bulb is burned out, the blinkers won't word on that side. You could have one bulb burned out on each side. Start the car, put left signal on. Check front and back lights. Is one light on but not blinking? If that's the case, the light that's not on at all is burned out and has broken the circuit so the good light stays on and won't blink. Check the other side. You also have a 'flasher' , actually 2. One for emergency flashers, one for the turn signals. It could be that the turn signal flasher is shot. You just have to unplug it to remove. It's probably located near the fuses. good luck countrycurt0

Posted on Aug 10, 2008

  • 14 Answers

SOURCE: 1998 jeep grand cherokee will not start

Try resetting the asd "auto shut down fuse had a similar problem the jeep would crank but did not get spark or gas also check your fuel pump? and the asd relay may be bad it will prevent the jeep from getting no spark and will not fire some jeeps have security problems

Posted on Jun 26, 2009

  • 5495 Answers

SOURCE: 1998 jeep grand cherokee limited fog lights don't work.

This means you have a short. I am assuming you are talking about the fog light fuse. Does this fuse blow whether the fog lights are off? or just when turned on?

If the fuse blows when the switch is off the switch is bad too. If the fuses only blows when the switch is turned on you have a short in the wiring or bulb.

I don't know if you have test equipment so first I would say to remove both driving bulbs from their sockets and see if there is corrosion. Fix that problem if there is corrosion.

Then install a fuse without the bulbs and see if the fuse blows. If you have a test light you can bridge the fuse panel without putting a fuse in. If there is a connection you have a hot wire grounding. If there is no problem install one light, fuse or bridge the fuse holder and see if 1 light works. Try each side. This way you can isolate the problem. Then visibly inspect wiring.

Posted on Jul 04, 2009

ZJLimited
  • 17970 Answers

SOURCE: where to replace coolant temp sensor for 1998 grand jeep cherokee

Check this image...

b33c4b0.png

...in the Section ZJ-Secc-8D-Ignition-Systems (page 5, fig. 10 and 11).

Good luck.



Posted on Sep 07, 2009

wracefans24
  • 1985 Answers

SOURCE: 1998 jeep cherokee sport- i get a code p1682.

p1682= Charging system voltage too low

Posted on Nov 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to know where is the blinker fuse on the 1998 jeep cherokee


i dont think it has a fuse. it has a switch on the fuse box that looks a n aluminium carmex jar. pull it out and replace it

Sep 20, 2010 | 1998 Jeep Cherokee

1 Answer

Signal and hazzard lights not working. Can you tell me which fuse to change?


I would also look at the blinker relay.It's a combination blinker/hazard relay.It's up under the dash on the left of the steering column.Hope this helps

Aug 31, 2010 | 1998 Jeep Cherokee

1 Answer

1998 Jeep cherokee Marker (left side only) lights not working


on 97 and later modles there is a fuse panel located behind a small access panel in the right cowl trim panel

Jul 16, 2009 | 1998 Jeep Wrangler

2 Answers

I need a fuse panel diagram to replace the turn signal flasher. Thanks


Before replacing the flasher does the hazards work, Try wiggling the turn signal lever up and down and back and forth with the key on and the lever in each position. If the blinkers or hazards start flashing you'l need a multifuntion switch. This isnt a definative test if you get nothing you may have a blown fuse. As fas as the flasher goes, go buy one and then you will know what it looks like.

Jul 14, 2009 | 1998 Jeep Cherokee

2 Answers

Blinker wont work, but the hazards do


There are two thermal flashers one for the Hazard Warning Lights and one for the Turn signal lights. It could be the flasher for the turn signals.

Oct 26, 2008 | 1998 Jeep Grand Cherokee

Not finding what you are looking for?
1998 Jeep Cherokee Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...