Question about 2006 Dodge Ram 1500

Open Question

Where is the egr sensor on a 4.7L dodge ram 1500 moter?

Looking to replace

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1596 Answers

SOURCE: 2005 Dodge 1500 code p0404 EGR valve.

The electronic EGR valve and solenoid assembly is attached to the rear of the left cylinder head ,

  1. Remove electrical connector (5) at top of EGR valve solenoid.
  2. Remove tube mounting bolt (1) at intake manifold.
  1. Remove two bolts (4) connecting EGR tube (1) to valve assembly.
  2. Remove gasket located between EGR tube flange and EGR valve assembly.
  3. Remove two EGR valve mounting bolts (5).
  4. Separate valve assembly (3) from engine.
  5. Remove and discard metal gasket located between cylinder head and valve assembly.
INSTALLATION
  1. Clean area at rear of left cylinder head where it joins base of EGR valve.
  2. Clean EGR tube where it joins EGR valve.
  3. Position new gasket between EGR valve and cylinder head.
  4. Position EGR valve to cylinder head. Install and tighten two bolts (5). Refer to Torque Specifications.
  5. Position new gasket between EGR tube flange and EGR valve assembly.
  6. Position EGR tube (1) to side of EGR valve and into intake manifold.
    1. Install EGR tube flange bolt (1) at intake manifold. Tighten bolt. Refer to Torque Specifications.
    2. Connect electrical connector (5) to top of EGR valve solenoid (2).Do a final tightening of two EGR tube bolts (4). Refer to Torque Specifications

Posted on Feb 05, 2009

  • 13 Answers

SOURCE: 2005 dodge ram 1500 still overheating after I had

it is possible that your coolent level is low or the thermostat that you just bought could be bad and one other thing there could be air in the system there for you gt to burp the system until the air is compleatly out

Posted on Jun 15, 2009

  • 412 Answers

SOURCE: my 2006 dodge ram 1500 5.7 liter the check engine

YOU NEED TO REPLACE EGR VALVE ASSEMBLY..SENSOR IS PART OF VALVE..FAIRLY EASY TO REPLACE..RECOMMEND DEALER PART..ALSO DISCONNECT BATTERY WHILE REPLACING

Posted on Jul 05, 2009

  • 249 Answers

SOURCE: replace timing chain on 03 dodge ram 1500 with 5.7 hemi

i have an 02 and i purchased a repair manual from autozone

Posted on Jan 05, 2010

  • 159 Answers

SOURCE: The temperature gauge on my 1999 Dodge Ram 1500 is

Check the gauge by holding in the trip odometer reset button and turn key to run,hold button for 10 seconds this will iniate a diagnostics on all the gauges,and lights if gauge doesn't move during this test replace gauge,if it does move then check the wires on the plug at the engine coolant temp sensor (ects) you can check the sensor by using a ohms meter by unpplugging it and check ohm's or resistance when cold and then start engine as the engine warms up the ohm's reading should gradually lower as the sensor is a thermister and as it warms up the resistance will drop.

Posted on Jun 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 dodge 1500 4 x 4 the engin mlight came on and the code is p0404. What does P0404 stand for?


SYMPTOM
P0404-EGR POSITION SENSOR PERFORMANCE

WHEN MONITORED
Engine running.

SET CONDITION
The EGR flow or valve movement is not what is expected.

POSSIBLE CAUSES
- Good trip equal to zero
- Excessive resistance in (F856) 5-volt supply
- (K34) EGR sensor signal circuit shorted to ground
- EGR assembly
- (K35) EGR solenoid control circuit
- Intermittent condition
- (K34) EGR sensor signal circuit open
- (K34) EGR sensor signal circuit shorted to ground
- (K900) sensor ground circuit open
- EGR assembly (ground)
- PCM
var classElements = new Array(); var node = document; var tag = 'a'; var els = node.getElementsByTagName(tag); var elsLen = els.length; var pattern = new RegExp("(^'\\s)specs_note(\\s'$)"); for (i = 0, j = 0; i

May 28, 2011 | 2004 Dodge Ram 1500

2 Answers

What is the fix for (egr flow sensor a) on 2007 dodge hemi? This code came up when light came on.


It is probably the EGR valve itself. I would remove the valve and check the lines coming off of it to make sure it is not clogged. If that checks out ok then I would replace the EGR Valve and then clear the code with a scan tool.

Mar 25, 2011 | 2007 Dodge Ram 1500 Quad Cab Sport

1 Answer

I have a po405 code , egr position sensor cuircuit high ,how do i change a egr valve on a 2006 dodge ram 1500?


Easy stuff my friend.use a 10mm socket and unbolt it from the head.also there's a tube and an 8mm socket can be used to remove them.4 bolts in all and replace the 2 gaskets.Erase the code if possible as well.

Dec 15, 2010 | 2005 Dodge Ram 1500

1 Answer

My 2006 dodge ram 1500 5.7 liter the check engine light is on it is giving me a code that says that the egr sensor voltage is too high is it the valve or the sensor that is bad or either


YOU NEED TO REPLACE EGR VALVE ASSEMBLY..SENSOR IS PART OF VALVE..FAIRLY EASY TO REPLACE..RECOMMEND DEALER PART..ALSO DISCONNECT BATTERY WHILE REPLACING

Jul 01, 2009 | 2006 Dodge Ram 1500

3 Answers

Where is the egr flow sensor on a 2005 dodge ram


I just took mine to the auto part store to find out. From what they told me its the little box on top of the Hemi Engine cover. They said I have to go to the dealer to get the part though.

Apr 10, 2009 | 2005 Dodge Ram 1500

1 Answer

P0406 Code


It is for the Exhaust Gas Recirculation (EGR) valve.

Feb 02, 2009 | 2005 Dodge Ram 1500

1 Answer

05 ram with hemi code p0406


Most of the times it is the EGR sensor that has gone bad. It is located in the back right side by the throttle body. You will see a hose that runs from the top of your EGR to the sensor. On your Dodge it is VERY eay to replace.

Jan 29, 2009 | 2005 Dodge Ram 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

288 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...