Question about 1994 Nissan Pickup

1 Answer

Oil Pan Removal - 1994 Nissan Pickup

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Nissan Master
  • 75,822 Answers

Disconnect the exhaust pipes, take the load of the mount bolts with a jack under the pan and remove the engine mounts, then remove the oil pan bolts and carefully raise the engine as high as you can off the mount pads, pry the Pan loose and reverse to put back together.

Posted on Feb 24, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have to lower the front crossmember to remove the oil pan. Is there any precautions I should know about? It is on 2004 jeep liberty 4x4


no engine stated, they even have diesel. or 3.7L GAS.
I toss my first coil, land on 3.7L V6.
great question, like the very first ever.
most just do it and get in trouble. vast posts in this.
but whats up, what is wrong, what part failed.?
this is best to know, so we can send you the official chapter on this from jeep.
sure use jackstands, never jacks only and never bricks .
04,KJ jeep 4wd pan off.
in chapter 9 ,under diagnostics, and pan leaks. that?
it says read
Refer to 9 -
ENGINE/LUBRICATION/OIL PAN -
REMOVAL). page 1555 (3.7L)
and i quote:
REMOVAL
1. Disconnect and isolate negative battery cable.
2. Install engine support fixture.
3. Raise and support vehicle.
4. Remove front wheel assemblies.
5. Remove skid plate (if equipped). (Refer to 13 -
FRAME & BUMPERS/FRAME/FRONT SKID
PLATE - REMOVAL)
6. Drain engine oil.
7. Mark adjustment cam position of front lower control
arm bolts.
8. Remove front lower control arm bolts. (Refer to 2 -
SUSPENSION/FRONT/LOWER CONTROL ARM -
REMOVAL)
9. Disconnect LH tie rod. (Refer to 19 - STEERING/
LINKAGE/TIE ROD END - REMOVAL)
10. Disconnect LH lower ball joint (Refer to 2 - SUSPENSION/
FRONT/LOWER BALL JOINT -
REMOVAL)
11. Disconnect LH strut clevis (Refer to 2 - SUSPENSION/
FRONT/CLEVIS BRACKET - REMOVAL)
12. Remove LH front axle (Refer to 3 - DIFFERENTIAL
& DRIVELINE/HALF SHAFT - REMOVAL)
13. Remove front axle brace bolts.
14. Remove front prop shaft. (Refer to 3 - DIFFERENTIAL
& DRIVELINE/PROPELLER SHAFT/
PROPELLER SHAFT - REMOVAL)
15. Drain front axle.
16. Using a transmission jack, support front axle.
17. Remove axle bracket bolts. (Refer to 3 - DIFFERENTIAL & DRIVELINE/FRONT AXLE - REMOVAL)
18. With RH axle still in place, remove front differential.
19. Remove transmission oil cooler line bracket.
20. Remove engine to transmission stiffening bracket.
21. Position Special Tool 8534 on fender lip and align the slots in the brackets with the fender mounting holes.
22. Secure brackets to the fender using four M6 X 1.0 X 25 MM flanged cap screws.
23. Tighten the thumbscrews to secure the sleeves to the support tube.
24. Secure the support tube in an upright position.
25. Assemble the flat washer, thrust bearing, hook and T handle.
26. Using the M10 X 1.75 mm flanged nut supplied with the support fixture, secure the chain to the front engine
lifting stud.
27. Loosen engine mounts.
28. Remove oil pan bolts.
29. Seperate oil pan (1) from engine.
30. Move oil pan to one side, remove oils sump bolt and windage tray bolts,
NOTE: Do not pry on oil pan or oil pan gasket. Gasket is integral to engine windage tray and does not come
out with oil pan.
end quote, (off)

Nov 30, 2016 | 2004 Jeep Liberty

2 Answers

How to remove the oil pan easy and safe from a 2005 crv honda


Hi Evelyn.here's a link on your oil pan removal,it says engine removal,will send a link on that too. SAVE 20 ON ONLINE SHIP TO HOME ORDERS OF 100 OR MORE Here's the engine removal guide. SAVE 20 ON ONLINE SHIP TO HOME ORDERS OF 100 OR MORE

May 17, 2015 | 2005 Honda CR-V

1 Answer

Remove a 2005 cr-v honda oil pan


Remove all bolts in the pan assembly. You may need to remove other objects that may obstruct the removal of the oil pan bolts. It would be a good idea to have the oil drained prior to pan removal. The oil pan uses a special RTV sealant instead of a gasket and can be a pain to seperate from the engine block. Use a soft faced hammer and strike the sides of the oil pan until it begins to loosen from the block. You can then use a screwdriver/prybar to seperate the seal and have the pan come off

May 17, 2015 | 2005 Honda CRV 2.2

1 Answer

How do iremove oil pan 01 montecarlo


OIL PAN
Removal & Installation
1. Disconnect negative battery cable. Remove engine torque strut. Raise and support vehicle. Drain
crankcase. Disconnect oil level sensor electrical connector. Remove oil level sensor and oil filter.
Disconnect front exhaust pipe from manifold. Remove right front wheel and splash shield.
2. Disconnect oil cooler pipes. Disconnect A/C compressor electrical connector. Remove A/C compressor,
and position aside. Disconnect engine mounts from frame.
3. Remove flexplate access cover. Use transmission jack at transaxle to raise engine. Remove oil pan bolts
and oil pan. To install, reverse removal procedure. Install oil level sensor after oil pan is installed. Tighten
retaining bolts to specification. See TORQUE SPECIFICATIONS.

Sep 25, 2014 | 2001 Chevrolet Monte Carlo

1 Answer

Oil Pan Gasket Replacement/ Oil Pan removal


yes the starter does have to be removed but also the engine mounts must be also as the engine must be raised about 10 " to get the pan out. if you do try this make sure you have very very sturdy jack stands for the engine to just a jack as the jack will lift it but wont maintain it long enough to safely remove the pan and reinstall it......good luck and be very carefull

Aug 11, 2014 | 1998 Oldsmobile Silhouette

1 Answer

What is the capacity(volum)of transmission and engin oil in denali 2007?


{: ) Engine Oil with Filter - All Engines 5.7 L (6.0 qt)
Transmission fluid:
4L60-E/4L65-E/4L70-E Pan Removal (4.7L), 4L80-E/4L85-E Pan Removal (7.3L),
6L50/6L80/6L90 Pan Removal (5.7L)

May 13, 2011 | 2007 GMC Yukon Denali

1 Answer

Removal of an oil pan on 1997 gmc silvarodo truck,2500 liking oil from oil pan gasket


It's quite rare for one of these pan gaskets to leak so before you take it off I would suggest thoroughly cleaning the entire pan and then going for a short test run then carefully inspecting the pan area again to see if you can pinpoint the exact source of the leak. Often I see the oil filter adapter or oil cooler lines [if equipped] leaking which can cause oil to run down the side of the pan and make it appear as though the pan gasket has failed. Sorry I don't have the procedure for removal of the pan but I rarely have to take one off for a leak. Hope this helps and good luck!

Mar 18, 2011 | 1999 Chevrolet C/K 2500

1 Answer

Need diagram for 2000 ford taurus oilpan


Oil Pan - Removal & Installation3.0L Engine
VIN S Engine
  1. Before servicing the vehicle.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Negative battery cable Dual converter Y-pipe Transaxle support bracket Oil pan by following the bolt removal sequence shown

    8d11698.jpg
    Fig. Oil pan bolt removal sequence-2000-04 3.0L (VIN S) engine


    2272e92.jpg
    Fig. Oil pan bolt tightening sequence-2000-04 3.0L (VIN S) engine
Hope helps (remember rated and comment this).

Aug 15, 2010 | 2000 Ford Taurus

3 Answers

The car is leaking oil and the mechanic said it was because there is a whole in the oil pan and it will cost 1800 to fix. can i buy another oil pan and put it on myself?


OIL PAN
REMOVAL
Drain engine oil.
Remove front engine mount bracket.
Remove power-train bending strut.
Remove structural collar from oil pan to trans-axle Structural Collar - Removal and Installation
Remove trans-axle lower dust cover.
If equipped with air conditioning, remove oil filter and adapter.
Remove oil pan.
Clean oil pan and all gasket surfaces.
INSTALLATION
Apply Mopar® Silicone Rubber Adhesive Sealant or equivalent at the oil pump to engine block parting line Oil Pan Sealing
Install a new oil pan gasket to pan.
Install pan and tighten screws to 12 N·m (105 in. lbs.)
Install oil filter and adapter.
Install trans-axle lower dust cover.
Install power-train bending strut.
Install front engine mount and bracket
CAUTION: The torque procedure for the structural collar must be followed, as damage to oil pan or collar could occur.

Install the structural collar Structural Collar - Removal and Installation using the following 3 step torque sequence:
Step 1: Install the collar to oil pan bolts and tighten to 3 N·m (30 in. lbs.)
Step 2: Install collar to trans-axle bolts and tighten to 108 N·m (80 ft. lbs.)
Step 3: Final torque the collar to oil pan bolts to 54 N·m (40 ft. lbs.)
Fill engine crankcase with proper oil to correct level.

Auto Zone carries the Oil pan you need for around $75.00 and they will have the step by step instructions for you to replace the oil pan. will take just over 2 hours for the average person. Good luck and keep me posted.

Nov 30, 2009 | 2002 Dodge Neon

1 Answer

New timing belt,oil change, then the car started to overheat,


pan removal requires hanging the motor with a sling and dropping the subframe ...it's a bear but pump and pan can be removed. silicone clogging the pick-up is common

Mar 17, 2009 | 2002 Volkswagen Passat

Not finding what you are looking for?
1994 Nissan Pickup Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...