Question about 1992 Plymouth Acclaim

1 Answer

1992 acclaim replaced timing belt airbag was deployed years ago. will airbag keep it from starting, is there a fuse or cut off switch

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 75 Answers

No, just the fact that the airbag was deployed will not keep the car from starting.

Posted on Feb 24, 2012

  • michael brown Feb 24, 2012

    before after airbag deployed a fuse blew car would not start, where is that airbag fuse

×

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

1fastbob
  • 301 Answers

SOURCE: whats the pattern to put a serpentine belt on a

If it's a v6 it is listed here.

http://www.gates.com/part_locator/index.cfm?location_id=3002

Just enter your vehicle info and click on the photo icon next to serpentine.

Hope this helps.

Bob

Posted on Oct 26, 2009

  • 1757 Answers

SOURCE: diagram for 92 acclaim serpentine belt

For the 1992 Plymouth Acclaim:
Click on the following free, direct Link. It has several Seprentine Belt Diagrams, including one to match your specific 1992 Plymouth Acclaim with the unspecified Engine: 2.5L SOHC In-Line 4-Cylinder or 3.0L SOHC V6; and the unspecified Engine Options (AC/No AC ect.)

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!


http://www.2carpros.com/car_repair_information/year/1992/make/plymouth/model/acclaim/1992_plymouth_acclaim_drive_belt_routing_diagram.htm

Posted on Apr 19, 2010

csmock132
  • 4669 Answers

SOURCE: about how much is it

about 200-230 if its a 4 cylinder.

Posted on Jun 02, 2011

  • 4977 Answers

SOURCE: where is the fuel cut off switch for 1992 plymouth

the only cut off is the fuel pump relay which is located on the drivers side inner fender among 2or 3 other relays by the computer.its been a while but i think its the 1st or 2nd in from the outer fender edge.

Posted on Jul 17, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

A few days ago the red light which indicates the air bags system on the front panel is now staying on. Can anybody help me get the light off - If not is it worth having it repaired


It is helpful to know the the year, make, and model of your car.

Just about all airbag systems will keep track of what has caused their problem. You need to have a shop or dealer with the right scanning tools read the airbag module and give you the diagnosis.

before you start your car the airbag module will scan all connections in the car, and if any do not have the correct signal it will flash the airbag light (this also indicates that the airbag system is not functional) so if you are in an accident while the light is on. the airbags will not deploy.

The problem could be a broken clock spring in the steering column, they are good for 15-20 years depending on how much the car was driven in those years. could be a faulty seat belt sensor, broken wire, bad crash sensor, Etc.

So get the car scanned and make short work of finding the problem, cost effective ?
You'll have to decide.

Apr 07, 2015 | Cars & Trucks

3 Answers

How to start a car that the airbags have deployed in?


Pull the fuse and or relays for the airbag

Apr 13, 2014 | 1997 Honda Civic

1 Answer

2001 pontiac grand am air bag module reset


Yes!!! You can replace it yourself.(Dont let others fool you into paying extra or telling you otherwise.)
-This is for pontiac grand ams 1999-2005 only.
-There are no frontal airbag impact sensors nor are there belt tensioners.
-The SRS system consists of only the (driver airbag) ,(passanger airbag),and the (airbag control module) in 1999-2005 grand ams.

If you crash/wrecked and airbags deployed you will need.
-Driver and Passanger airbags
-Airbag control module

You can buy cheap airbags from a local junkyard any year from 1999-2005 will fit.
You can also find an airbag control module for cheap at your local junk yard BUT YOU MUST FIND ONE WITH THE SAME (PART NO.) AND (SERV NO.) AS THE ONE YOUR REPLACING.The (part no.) and (serv no.) should be at top left of airbag control module.However it does (Not) have to match numbers under barcode or the numbers at the far bottom right of airbag control module.

After you get both airbags and airbag module
-Disconnect car Battery
-Replace airbags
-Replace airbag module (under passanger seat)
-Double check all connections and connect battery.

Congradulations!Your airbags should be back online.

Notes: Two torx 35 head screws hold the driver airbag, access is through two holes behind steering column.
To remove passanger airbag you have to remove glovebox it uses (7mm)screws.After you remove you will see a pair of (10mm)screws holding airbag.
To remove airbag control module First remove passanger seat 2(15mm).Then after removing you will notice a raises area kinda like a vertical bump.Take a razor blade to your carpet and cut it to explose the module underneath.
The airbag module is held by three screws depending on the year of your car it varies.Most likely 3 (10mm).

Mar 24, 2013 | Pontiac Grand Am Cars & Trucks

1 Answer

How do i deactivate srs so i can replace front seatbelts on 2005 yaris


Disconnect the battery negative terminal.
1. Wait at least 90 seconds after the ignition switch is
turned off and the negative (-) terminal cable is
disconnected from the battery before starting the
operation.
(The SRS is equipped with a back-up power source, so
if work is started within 90 seconds of disconnecting
the negative (-) terminal cable of the battery, the SRS
may be deployed).
2. Do not directly expose the steering pad, front
passenger airbag assembly, center airbag sensor
assembly, front airbag sensor, front seat inner belt
assembly, seat position sensor, occupant
classification ECU, front seat side airbag assembly,
side airbag sensor, curtain shield airbag assembly,
rear airbag sensor or front seat outer belt assembly to
hot air or flames.

Feb 26, 2013 | 2005 Toyota Yaris 1.3

1 Answer

Won't start after airbags deployed? (NOT inertia switch)


Assuming the pump has not died, you should be able to jumper the pump relay.
The lite blue and orange wire should be power from the fuse, and the dark green and yellow wire should go to the inertia switch then to the pump.


2_10_2013_1_27_30_am.gif

Feb 10, 2013 | 1998 Ford Explorer

1 Answer

Airbag code 32 fix?


If you replaced the airbags, it might be that the code just needs to be turned off. I had the same thing with mine, sometimes the code is not turned off after replacement.

Apr 18, 2012 | 1998 Ford Escort

1 Answer

Front impact crash & airbag did not diploy


Airbags have specific criteria for deployment that determines whether impact was severe enough to deploy bags or whether only 1 stage deployment is needed or may decide impact was minor enough that deployment of airbags could potentially be more dangerous than the actual impact. For instance I was on the expressway last year going 65mph and someone rear ended me at over 100mph. Totaled my Ford Focus, her airbag did not deploy. Over certain speeds depending on the vehicle calibration, and airbag should never deploy. With an impact under a designated speed or over a designated speed a deployment can be dangerous. As long as your airbag light was not on before the crash I'd say your system was working properly and did not malfunction. If your airbag light ever comes on just keep in mind that any airbag malfunction will disable the system and turn on the light

Apr 19, 2011 | 1998 Ford Taurus

1 Answer

Diagram for 92 acclaim serpentine belt


For the 1992 Plymouth Acclaim:
Click on the following free, direct Link. It has several Seprentine Belt Diagrams, including one to match your specific 1992 Plymouth Acclaim with the unspecified Engine: 2.5L SOHC In-Line 4-Cylinder or 3.0L SOHC V6; and the unspecified Engine Options (AC/No AC ect.)

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!


http://www.2carpros.com/car_repair_information/year/1992/make/plymouth/model/acclaim/1992_plymouth_acclaim_drive_belt_routing_diagram.htm

Apr 17, 2010 | 1992 Plymouth Acclaim

1 Answer

I have a 2001 ford escape that was in a fender bender. minor visual damage but both airbags deployed. I bought new steering wheel and passanger airbag and hooked up. I was told i now need new sensors which...


this may sound crazy but this is what they say (manufactor) when ever airbags are deployed ,the following must be replaced,the deployed bags. the airbag module,crash sensors,clock spring, the belt buckles and seat belts should be inspected and checked.

Mar 08, 2010 | 2001 Ford F150 Styleside SuperCrew

Not finding what you are looking for?
1992 Plymouth Acclaim Logo

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7689 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...