Question about 1993 BMW 325

Open Question

Need torque specifications and sequence for big end bearings and main bearings for bmw e36 325i m50 non vanose

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

steve_e_uk
  • 1675 Answers

SOURCE: torque settings for bmw 316

hi for main bearings it is stage 1 : 25nm leave for 10 mins then stage 2 its turn 53 degrees for big end bearings it is stage 1 : 23nm leave for 10 mins then stage 2 its turn 70 degrees hope this helps

Posted on Jan 01, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque settings on a yaris 1.3 16v big ends,mains,flywheel,cylinderhead


Toyota Yaris Main and Big end Torque settings:
Tighten the main and big end bolts in sequential order and in two steps.
Main bearings. Stage 1.
22 ft lbs.
Stage 2.
44 ft lbs

Big end bearings.
Stage 1.
11 ft lbs.
Then Rotate bolt head a further by 90 degrees

Head bolt torque must be done in 3 steps:
1st 22 ft lbs
2nd 43 ft lbs
final 47 ft lbs
use this sequence of tightening:
9 - 3 -1 -6 -8
7 - 5 - 2 -4 - 10

Flywheel spec:
65 ft lbs

Jul 15, 2016 | 2007 Toyota Yaris

1 Answer

Tercel 1992 main bearings torque


The Main Bearing Cap TorqueTo install:
  1. When reassembling, clean the bearing caps and journals in the block thoroughly. Coat the bearings with a liberal application of clean motor oil.



0900c15280051ec0.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: Always torque the bearing caps to specification


0900c15280051ec1.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 4: Main bearing cap bolt tightening sequence on 3E and 3E-E engines

  1. Fit the upper bearings halves into the block and position the lower bearing halves in the bearing caps.
  2. Place the crankshaft into the engine block, making sure it fits exactly into its mounts.
  3. Install the upper thrust washers on the center main bearing with the oil grooves facing outward.
  4. Install the main bearing caps and the lower thrust washers in the proper sequence. Make sure the arrows on the caps point towards the front (pulley end) of the motor.
  5. Tighten the cap bolts to specification in three passes. On 3E and 3E-E engines, use the correct sequence.
  6. Double check the end-play of the crankshaft by repeating the procedure described earlier.
  7. Turn the crankshaft through one or two full clockwise rotations, making sure that it turns smoothly and evenly with no binding.
  8. Attach the piston rods, following procedures given earlier in this section. Remember that the rod caps must be reinstalled in their original positions.
  9. Install a new rear main oil seal into the retainer and install the retainer onto the block. Tighten the bolts to specification.
  10. Install the rear end plate on the engine.
  11. Install either the driveplate (automatic) or the flywheel (manual), observing the matchmarks made during removal.
  12. If equipped with a manual transaxle, reinstall the clutch disc and pressure plate.
  13. Install the oil pump.
  14. Install the oil strainer and oil pan, using new gaskets.
  15. Rotate the engine into its upright position and continue reassembly of the timing belt, idler pulley and covers.
  16. Reinstall the engine in the car, following procedures outlined earlier in this section.
42 Foot pounds (Final torque)

Dec 15, 2012 | 1992 Mitsubishi 3000GT

1 Answer

Torque settings for bmw 316 e36 big end bearings and main bearings


hi for main bearings it is stage 1 : 25nm leave for 10 mins then stage 2 its turn 53 degrees for big end bearings it is stage 1 : 23nm leave for 10 mins then stage 2 its turn 70 degrees hope this helps

Jan 01, 2011 | BMW 3 Series Cars & Trucks

1 Answer

What is the right Torque Specification of the cylinder head bolt,main bearing and connecting rod bearing for a 1997 Ford F 150 4.2 liter? Thank you...


Cylinder heat bolt torque:
Torque sequence --------- front | 7 3 1 5 | | 8 4 2 6 | --------- Step 1: Torque all bolts in sequence to 14 Ft/Lbs Step 2: Torque all bolts in sequence to 29 Ft/Lbs Step 3: Torque all bolts in sequence to 36 Ft/Lbs Step 4: in the sequence, loosen the cylinder head bolts three turns. Step 5: Tighten short bolt to 15 - 32 Ft/Lbs Step 6: Tighten long bolt to 30 - 36 Ft/Lbs Step 7: Tighten all bolt to 175- 185 degree note: Do not loosen all of the cylinder head bolts at one time. Each cylinder head bolt must be loosened and the final tightening prior on the next bolt in the sequence.
Main bearing torque:
Torque sequence: Step 1: torque bolts to 91 Ft/Lbs with the exception of the rear main bearing cap Step 2: torque rear main bearing cap bolts to 88 Ft/Lbs Step 3: torque brace bolts to 40 Ft/Lbs
Connecting rod torque:
Torque sequence Step 1: Torque to 29 Ft/Lbs Step 2: Turn an additional 90 degrees

May 17, 2010 | 1997 Ford F150 Regular Cab

1 Answer

I need the torque specs for the main and rod bolt for a 99 escort 2.0l engine


engine tightening torques
Main bearings Renew bolts/nuts No
Main bearings Stage 1 43 Nm
Main bearings Stage 2 85 Nm
Big end bearings Renew bolts/nuts Yes
Big end bearings Stage 1 15 Nm
Big end bearings Stage 2 90°

Jan 21, 2010 | 2004 Ford Focus

1 Answer

2003 mazda 6 3.0 need the main bearing torque specs


I'm sending you the torque specifications for your main bearings and also your head bolts. I also sent you main bearing and cylinder head tightening sequence. I hope this will be useful2c713bf.giffce6623.gif
Main Bearings Torque specs. 40-43 Ft. Lbs.
Cylinder Head Torque specs. 56-60 Ft. Lbs.

Oct 05, 2009 | 2003 Mazda Mazda6

2 Answers

WOULD YOU KNOW THE TORQUE SETTINGS FOR MAIN BEARING AND BIG END BEARING CAPS FOR ISUZU 4JG2 ENGINE


Mains Stage 1 83nm
Mains Stage 2 167nm

Big ends Stage 1 29nm
Big ends Stage 2 45 - 60 degrees

Hope this helps

Jul 10, 2009 | 1994 Isuzu Trooper

3 Answers

Need torque specs


Torque sequence:
Step 1: Torque 29 to 34 Ft/Lbs
Step 2: Torque an additional 90 to 120 degrees

Oct 14, 2008 | 1997 Ford F150 Regular Cab

Not finding what you are looking for?
1993 BMW 325 Logo

Related Topics:

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...