Question about 1997 Chevrolet Lumina

Open Question

Gas tank makes popping sound

Canister purge valve is new

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
chiquititas
  • 1010 Answers

SOURCE: 96 corsica error cod po441 no purge flow

Look, that code means:
P0441 - Evap emission control system Incorrect purge flow

so try to replace the emission control.

Posted on Jun 19, 2008

Ad
  • 104 Answers

SOURCE: I have a 2004 Avalanche, 49K mileage, code PO446,

That is an EVAP code. its a vent control code. you can manually test it by powering it up if you know where its at. i cant remember exaclty where its at off the top of my head but its only 2 wires. using a volt meter you want to make sure power is getting to it, but you cannot activate it without dealer scan tool.hmmm if you can figure out which is ground and power when you give it 12 volts it should click. meaning your vent solenoid works and you have wiring problems or its leaking.

EVAP problems are hard to finde with out scanners. you can change the vent solenoid and hope it fixes it. but a code points you to the direction of a problem. hopefull its not wiring problems. in the northern states with snow. ice can pull out wires and also get clogged in the vent solenoid and lock it up. its either wiring or bad or a leaking solenoid. check condition of wires. if they look good try a vent soleniod.

if that doesnt fix it after a engine light reset and 2 weeks or so. then goto dealer. you need to reset it after repair. light will not go off on its own.GOOD LUCK

Michael
ASE certified.
plz rate

Posted on Apr 29, 2009

  • 2 Answers

SOURCE: where is the purge solenoid and canister on a 1996...

its on the drivers side, behind the rear tire, under the plastic cover. To remove it, lift the rear of the car with ramps and remove the plastic cover under the tire.

Posted on Jul 08, 2010

  • 37 Answers

SOURCE: 2004 Chevy Cavalier 2.2 eco Automatic 94,000 miles

in my experience the usual culprit is the evap cannister. the problem is it gets moisture in it and freezes during winter thus cracking the plastic. if you lay under the car and look at the evap box it black plastic and if you see a loose or cracked hose or the box itself is cracked that is most likely it. as a side note you can check the gas cap and buy a new one to see if that rectifies the situation. lastly i don't think the gas tank should be suspect as you would probably notice if gas was leaking out of the tank. if you take the car to a dealer or shop they can do a smoke test and determine where the leak is.

Posted on Oct 19, 2010

  • 1 Answer

SOURCE: insufficient egr flow, already replaced egr valve

I too replaced the egr valve and was discouraged that the check engine light came back on with the same "insufficient flow" code. I took it to my mechanic to put it on the monster diagnostic machine. It said "check all vacuum line, and or map sensor". After looking real close we found a melted vacuum tube, and a cracked vacuum angle connector. Replaced both vacuum pieces, reset the codes, and good to go. If that fails than the next thing is the map sensor, that tells the EGR valve what to do.

Posted on Jan 28, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dropping fuel tank


I am not sure why you are dropping gas tank. Canister purge valve should be located near intake manifold under hood of car. hope this helps

Aug 01, 2014 | 2002 Pontiac Firebird

1 Answer

I have a 1999 Monte that builds pressure in the gas tank and need help because it has pop two gas tanks why is it building pressure .


Back by your tank, there is a vapor canister with a vent valve on it. That valve is supposed to let vapor from the tank into the canister. Check to see if the valve is working. You can test it by connecting it directly to the battery with some jumper wires. Once in the canister, the vapors are opened to the engine vacuum for burning by the purge valve once the car is warmed up and on the road. If the vent valve is working, but pressure is still building, the problem can be the purge valve at the engine. You can tell this is the problem if the cannister is full of liquid gas. Normally, and depending on the failure mode, these failures would set the engine light. If the light is on, get a scan to see where the problem is. Please let me know if you have more questions, and thanks for using FixYa.

vent valve/canister:
jturcotte_522.jpg

Jun 16, 2011 | 1999 Chevrolet Monte Carlo

1 Answer

Ford 1998 windstar 3.0l, when open gas tank cap, air pressure release sound occurred immediately.Although replaced a new cap, the situation is still exist.


HAVE EVAP SYSTEM CHECKED. YOUR FUEL PRESSURE SENSOR NOT WORKING.CHECK THE CANISTER FUEL VAPOR HOSE AND INLET PORT FOR BLOCKAGE OR COLLAPSED HOSES.CHECK CANISTER PURGE VALVE HOSES FOR KINKS.HAVE CHARCOAL CANISTER CHECKED MAKE SURE ITS NOT GAS SOAKED AND PLUGGED. THE DEALERSHIP HAS TO RUN A DIAGNOSTIC TEST TO CHECK OUT WHOLE EVAPORATIVE EMISSION CONTROL SYSTEM.

Dec 25, 2010 | 2001 Ford Windstar

1 Answer

The vehicle wont accept fuel it spills all over and gas gauge is stuck over full??? but runs out of gas,then very very very slowly it accepts very little gas then you can drive again.chevyscott20@yahoo.com


SOUND LIKE YOUR EVAPORATIVE EMISSION CONTROL NOT WORKING.SCAN VECHICLE FOR FOR FAULTY FUEL TANK PRESSURE SENSOR MALFUNCTION.AND THE CANISTER PURGE SOLENOID VALVE OR CANISTER VENT SOLENOID NOT WORKING.CAUSING EXCESSIVE FUEL PRESSURE AND FUMES BUILD UP IN FUEL TANK.CHECK CANISTER IT COULD BE GAS SOAKED NEED REPLACING OR VACUUM LINES GOING TO CANISTER PURGE SOLENOID OR VENT SOLENOID COULD BE BROKEN.PURGE VALVE LOCATED ON THE LEFT SIDE OF THE ENGINE ON A BRACKET AND VENT SOLENOID LOCATED ON A BRACKET NEXT TO FUEL TANK.CHECK BOTH MAKE SURE VACUUM LINES NOT BROKE OR DISCONNECTED.MAKE THE ELECTRICAL CONNECTOR INTACT ALSO.FUEL PRESSURE SENSOR ON TOP OF TANK ON THE FUEL PUMP MODULES.ALL YOU CAN DO IS REMOVE CANISTER SEE IF FULL OF GAS REPLACE IT.AND CHECK FOR BROKE AND DISCONNECTED VACUUM LINES.THE DEALERSHIP HAS TO HOOK UP DIAGNOSTIC EQUIPMENT CHECK IT OUT.BE CHEAPER BECAUSE ALL THEM EVAP PARTS NOT CHEAP THAT WHY LET DEALERSHIP SCAN IT SAVE MONEY IT WILL CUT THE COST.WARNING DONT KEEP DRIVING VECHICLE.GAS VAPORS PRESSURE BUILD UP ON HOT DAY FUELTANK WILL BLOW UP LIKE BALLON.PRESSURE KEEP BUILDING UP.

Oct 16, 2010 | 2001 Chevrolet Blazer

3 Answers

Po446 evap vent code where is the evap vent located


Some might have an ses p0446, evap emissions vent circuit low. If you take it to the dealer they want 300-400.00 to fix the problem. GM has a service bulletin on this condition and have the updated part for 180.00, thats suppose to eliminate this issue.

Basically the problem is, the evap purge vent valve gets clogged with dirt, especially if the truck is used in dirty conditions. Well I figured there had to be a cheaper way to cure this problem.

Here it is:
1) find the location of the vent valve; its under the truck, locate the charcoal canister on the front of the gas tank and trace the vent line to the vent valve.
2) Take the bracket loose with a 5/8 wrench.
3) Spin the valve around so the side with the hole is facing you.
4) Take an air compressor and blow the vent valve out.
5) reinstall and clear the code and it's fixed.

Now I know the updated part from gm is supposed to keep the valve from clogging ever again, but why spend the money when all you have to do is blow out the vent valve every 50k-100kmi and save your $$$!

Subject: DTC P0446 (Restricted/Blocked EVAP Vent Path) Set, Service Engine Soon (SES) Lamp Illuminated (Replace Hose/Evaporative Emission (EVAP) Canister Vent Asm) #02-06-04-037A - (02/02/2005)
Models:
- 1999-2003 Chevrolet Silverado Models
- 1999-2003 GMC Sierra Models
--------------------------------------------------------------------------------
This bulletin is being revised to add model years. Please discard Corporate Bulletin Number 02-06-04-037 (Section 06 -- Engine/Propulsion System).
--------------------------------------------------------------------------------
Condition
Some customers whose vehicles are operated in dusty type environments, such as farming or mining off-road type applications, may comment about the illumination of the instrument panel SES light, with a DTC of P0446 (Restricted/Blocked EVAP Vent Path) being set.

Cause
Dirt and dust intrusion into the EVAP canister vent hose assembly, resulting in restricted air flow, may cause this condition.

Part Number 15086429 Hose Asm-Evap Emis Cnstr Vent


Removal & Installation
Purge Solenoid Valve-2.2L (L61) Engine
  1. Disconnect the evaporative emission (EVAP) canister purge valve harness connector.
  2. Disconnect the vacuum pipe from the EVAP canister purge valve.
  3. Disconnect the purge pipe from the EVAP canister purge valve.
  4. Remove the EVAP canister purge valve and bracket.
  5. Remove the EVAP canister purge valve from the purge bracket.
  6. Inspect for carbon release in the EVAP canister purge valve ports.
To install:
  1. Install the EVAP canister purge valve on to the purge bracket.
  2. Install the EVAP canister purge valve and bracket. Tighten the purge bracket nut to 71 inch lbs. (8 Nm).
  3. Connect the purge pipe to the EVAP canister purge valve.
  4. Connect the vacuum pipe to the EVAP canister purge valve.
  5. Connect the EVAP canister purge valve harness connector.
  6. Remove the air cleaner outlet resonator.
  7. Disconnect the EVAP canister purge valve harness connector.
  8. Disconnect the engine purge pipe from the EVAP canister purge valve.
  9. Disconnect the engine vacuum pipe from the EVAP canister purge valve.
  10. Remove the EVAP canister purge valve mounting bracket attaching bolt.
  11. Remove the EVAP canister purge valve along with the mounting bracket.
  12. Installation is the reverse of the removal procedure. Tighten the bracket bolts to 71 inch lbs. (8 Nm).

Purge Solenoid Valve-2.4L Engines
  1. Remove the front purge pipe from the evaporative emission (EVAP) canister purge valve.
  2. Remove the rear purge pipe from the EVAP canister purge valve.
    NOTE The EVAP canister may have released carbon particles, which caused this part to fail, and may cause damage to other components. Check the EVAP canister for loose carbon before returning the vehicle to service.
  3. Disconnect the EVAP canister purge valve electrical connector.
  4. Insert a screwdriver between the EVAP canister purge valve and the mounting bracket in order to release the lock tab.
  5. Remove the EVAP canister purge valve mounting bracket attaching nut, if replacing the bracket.
  6. Remove the bracket.
To install:
  1. Install the mounting bracket and the attaching nut for the EVAP canister purge valve. Tighten the nut to 71 inch lbs. (8 Nm).
  2. Slide the EVAP canister purge valve onto the mounting bracket. Make sure the lock tab locks the valve in place.
  3. Connect the EVAP canister purge valve electrical connector.
  4. Connect the rear purge pipe to the EVAP canister purge valve.
  5. Connect the front purge pipe to the EVAP canister purge valve.

Vent Solenoid Valve-2.2L & 2.4L Engines
  1. Raise the vehicle
  2. Loosen the EVAP canister vent valve hose clamp and slide the clamp down the hose away from the EVAP vent valve hose connection.
  3. Remove the hose from the EVAP canister vent valve.
  4. Remove the EVAP canister vent valve by placing a pry bar between the valve and mounting surface, and moving the valve forward.
  5. Remove the clip from the EVAP canister vent valve harness connector
  6. Disconnect the EVAP canister vent valve harness connector.
To install:
  1. Connect the EVAP canister vent valve harness connector
  2. Install the clip into the EVAP canister vent valve harness connector.
  3. Install the EVAP canister vent valve by pushing the mounts into the original holes.
  4. Lubricate the hose end with lubricant.
  5. Install the hose to the EVAP canister vent valve.
  6. Slide the EVAP canister vent valve hose clamp down on to the hose connection at the EVAP canister vent valve.
  7. Lower the vehicle.

Hope this help (remember commetn and rated this).

Apr 21, 2010 | 2000 GMC Jimmy

2 Answers

2002 GMC Z-71 Check Engine Light codes????


Off hand, it's by your oil fill tube on top off motor.

Mar 30, 2010 | 1999 Chevrolet Silverado 1500

2 Answers

Check valve missing in fuel tank filler neck.


P1444 Purge Flow Sensor Circuit Input Low 0
The evaporative emission control system checks to make sure there are no leaks in the lines that run from the gas tank to the charcoal canister and up to the engine. It also checks to make sure the gas cap is sealing correctly.
When you fill your car with gas, the vapors in the tank get forced into a canister filled with activated charcoal. Also, on a hot day as the gas heats up and vaporizes, those same vapors push into the canister where they're stored. But the charcoal can only hold so much vapor. At some point it has to be emptied. The emptying process is called "canister purge." Here's how it works.
The computer orders a canister purge by powering open a PURGE solenoid. That opens the vacuum line between the canister and the intake manifold. At the same time, it opens a VENT solenoid. That allows fresh air into the canister. So the engine is literally sucking out the gas vapors and purging the canister with fresh air. The computer has to adapt its fuel strategy to take advantage of all the extra gas vapors coming into the engine.
The computer notices the canister is empty when it detects a leaner condition (all the vapors are used up) and it resumes normal fuel delivery. Some car manufacturers then close the VENT solenoid but leave the PURGE solenoid open. That creates a vacuum throughout the entire fuel storage system. Once the correct vacuum is reached, it closed the PURGE solenoid and waits to see if the vacuum holds. If it doesn, the system passes the test. If it detects a leak, it sets a code.
In this code P1444, the computer sees a lower than expected value on the purge flow sensor. bottom line? replace the purge flow sensor.

Sep 03, 2009 | 2006 Chrysler Town & Country

1 Answer

2000 ford taurus gas tank has what appears to be a fitting on the top right rear that has hoses attached. there are stains and gas smell coming from this area. my repair manual mentions a plastic push...


The Evaporative Emission Control System monitors the fuel vapor flow between the engine intake manifold and the EVAP canister. The system failure occurs when a leak or blockage between the intake manifold, the EVAP canister purge valve and the EVAP canister is detected by the PCM.

Code P1443 Possible Causes:

- Pinched, blocked or plugged fuel vapor tubes/hoses (except between fuel tank and EVAP canister)

- Damaged EVAP canister

- Disconnected, cracked or cut fuel vapor tubes/hoses (except between fuel tank and EVAP canister)

- Damaged EVAP canister purge valve

Notes: Check for audible vacuum noise in the engine compartment or significant fuel odor in the engine compartment or near the EVAP canister.

On my '98 4x4, the cannister purge valve is located under the hood, mounted on the driver's side fender.

The EVAP cannister itself is located underneath the truck, in back, between the spare tire and the truck bed (have to remove the spare to get at it).

If it were me I would hold off on replacing parts...I'd drive around some more first, making sure that I don't overfill the gas tank or run it dry and making sure I replace the gas cap properly, etc. If the code returns, then its time to think repairs.

Jul 02, 2009 | 2000 Ford Taurus

1 Answer

04 GMC Yukon won't start on less than 1/4 tank of gas


have your evaporative emission control system check.sound like you have purge valve solenoid not working or vent valve control solenoid.have it scan.to see which component not working..reason your gas tank expanding. your fuel vapor building up pressure.your purge valve and vent valve open allowing gas vapor from charcoil canister. to be burn in the intake manifold to be burn in combustion chamber.

Jun 06, 2009 | 2006 GMC Yukon

1 Answer

Engine does not start after filling it


Sounds like you have a bad vent valve in the gas tank. When you fill the tank gas also fills the emission vapor canister. When you try to start it, the gas is pulled through the canister purge solenoid, flooding the engine. To test this, unplug the canister purge solenoid and see if the problem stops.

Mar 26, 2009 | 2005 Subaru Outback

Not finding what you are looking for?
1997 Chevrolet Lumina Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...