Question about 1996 Jeep Cherokee

Open Question

Where can i buy reg light bulbs for 1998 cherokee limited

Posted by on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 132 Answers

SOURCE: BACKUP LIGHTS NOT WORKING

on the transmission

Posted on Feb 03, 2009

Ad
  • 715 Answers

SOURCE: I need to replace the signal light bulb on the

open hood REMOVE SCREWS ON TOP HOLDING LIGHT ASSEMBLY IN THEN PULL WHOLE ASSEMBLT STRAIGHT OUT YOU MAY NEED TO TUG A LITTLE BUT IT WILL COME OUT

Posted on Apr 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 01 grande Cherokee keeps blowing brake


the bulbs you mean, not the BRAKE FUSES?????

blows what.
if the lamps blow, they are the wrong lamps
or the alternator regulator has gone berserk and the line voltage , is over 15vdc.
my guess is bulbs.
and would be system over voltage.
i had one car in 1984 that the reg went nuts and blew out all bulbs in the, car at 2am. (and not a nice part of town either,,,,)
up upgraded that car to electronic reg. ,
like i do all my classic cars now.

buy a cheap 10 buck DMM volt meter at walfart.
and put it across battery terms, running and racing idle.
13.3 to 15vdc is legal range.

Sep 27, 2014 | 2001 Jeep Grand Cherokee

1 Answer

My license plate lights are out on my 97 grand cherokee limited all the fuses are good and i replaced the bulbs, everything is good as far as the connections just dont know whats going on. can some one...


The lights are on the same circuit with the side marker lights. So if those work, and you don't have power at the lic plate sockets, somethings going on with the wiring harness in the back of the truck.
If you have power the ground circuit may be damaged.

Aug 03, 2013 | 1998 Jeep Grand Cherokee

1 Answer

1998 Jeep Cherokee sport, keeps blowing brake light fuse. if I take the bulbs out the fuse doesnt pop but as soon as i put the bulbs back in and hit the pedal it pops.?


Check wire from fuse to light,there is short somewhere, also check light connector, has the car been in an accident lately?

Sep 30, 2011 | 1998 Jeep Cherokee

1 Answer

I need to replace the signal light bulb on the front drivers side of my 1998 jeep grand cherokee limited. I don't see how to get access to it.


open hood REMOVE SCREWS ON TOP HOLDING LIGHT ASSEMBLY IN THEN PULL WHOLE ASSEMBLT STRAIGHT OUT YOU MAY NEED TO TUG A LITTLE BUT IT WILL COME OUT

Apr 03, 2010 | 1998 Jeep Grand Cherokee

1 Answer

Imobliser on my renault megane cabriolet 1998 r reg wont turn off


the pins on the lazer bulb in your keyfob has snapped off caused buy pressing the button too hard. (the red light will still come on but the key wont work)

heres what to do

open your keyfob and pull the lazer bulbs pins to the other side of the chip board. solder it to the wrong side where you see the nipples (dont worry there still in the right place) and shove a bit of bog roll in there to stop the chip board moveing when you press the button

Oct 20, 2009 | 1986 Renault Sport

2 Answers

1998 jeep grand cherokee limited fog lights don't work.


This means you have a short. I am assuming you are talking about the fog light fuse. Does this fuse blow whether the fog lights are off? or just when turned on?

If the fuse blows when the switch is off the switch is bad too. If the fuses only blows when the switch is turned on you have a short in the wiring or bulb.

I don't know if you have test equipment so first I would say to remove both driving bulbs from their sockets and see if there is corrosion. Fix that problem if there is corrosion.

Then install a fuse without the bulbs and see if the fuse blows. If you have a test light you can bridge the fuse panel without putting a fuse in. If there is a connection you have a hot wire grounding. If there is no problem install one light, fuse or bridge the fuse holder and see if 1 light works. Try each side. This way you can isolate the problem. Then visibly inspect wiring.

Jul 04, 2009 | 1998 Jeep Cherokee

1 Answer

Remove head light to replace bulbs


You have to be careful-the whole assembly snaps in and out

Sep 22, 2008 | 1999 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...