Question about 2000 Daewoo Lanos

Open Question

Daewoo lanos camshaft replacement - 2000 Daewoo Lanos

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 6 Answers

SOURCE: reset passcode for radio of 2002 daewoo ,lanos

MINE CAME ON A SMALL METAL TAG ON THE SPARE KEY

Posted on Jul 16, 2008

  • 219 Answers

SOURCE: locating camshaft positioning sensor on 2000 Daewoo Laganza

hi,
it is under the upper timing belt cover between the camshaft gears. According to the manual touching anything related to timing belt requires removing million parts including right front wheel. I suspect this might be an overkill just to remove upper timing belt cover.

So my advice would be to get it done by some mechanic as u will not be able to do it and may damage other parts also.

Thanks!
Sandy

Posted on May 18, 2009

emissionwiz
  • 75822 Answers

SOURCE: Where is the timing mark for the camshaft on a 2000 Daewoo Lanos?

Here is the entire timing belt replacement procedure.
Required tools:
13mm open end wrench 10mm shallow and deep socket 8mm socket long flathead screwdriver 17mm deep socket T50 torx socket 1/4", 3/8ths and 1/2" ratchets and extensions E10 inverted torx sockets 6mm Allen wrench 15mm open end wrench 7mm socket 12mm open end wrench 14mm socket 12mm socket 8mm, 9mm and 10mm Allen head sockets 19mm socket pry bar needle nose pliers
If you are doing this because your timing belt broke you will also need to buy a complete cylinder head, head gasket set, and both idler pulleys. ALL DAEWOO MODELS WILL BREAK THE INTAKE AND EXHAUST VALVES WHEN THE TIMING BELT BREAKS.
Start by removing the air cleaner assembly from the throttle body, remove the air filter and housing jack up the vehicle and remove the wheel, remove the plastic shielding in front of the accessory drive belt assembly, remove the accessory drive belt, place a jack with a block of wood on top underneath the engine oil pan remove the front engine mount, remove the crank shaft pulley ( the 4 Allen head bolts only not the 17mm bolt in the center.) remove the metal plate behind the engine mount bracket on the engine, remove the plastic timing belt cover 3 clips on top 2 10mm bolts on bottom. Rotate the engine until the #1 cyl. is at Top Dead Center on the compression stroke or line up the crankshaft timing mark with the mark on the inner timing belt cover ( notch in cover with notch in pulley) on the camshaft pulleys -- ( intake cam line up the line on the pulley with the line on the inner cover)( exhaust cam line up the arrow on the pulley with the arrow on the inner cover) loosen the 13mm bolt in the belt tensioner and using the Allen wrench rotate the tab until there is slack in the belt. Remove the belt. At this time I would recommend you replace the water pump, both plastic idler pulleys as they tend to overheat and lockup, and the belt tensioner. Make sure all your marks are lined up, you may need a helper to hold the Exhaust Cam in place as it tends to move during belt installation. Put the timing belt underneath the crankshaft pulley, install the belt leaving the intake cam for last and NO BELT SLACK on the right side between the crank and the exhaust cam. Once the belt is installed rotate the crankshaft over 2 revolutions and make sure is rotates freely, and your timing marks are aligned perfectly if not the engine will not run properly, tension the belt as needed. Installation is the same as removal.

To clarify, on the DOHC engine, the intake cam gear has a line on it, and the exhaust cam gear has an arrow on it. These should be lined up with the corresponding line and arrow on the VALVE COVER, pointing straight up. I just went through this process over the weekend, and spent quite a bit of time looking for these marking as I had removed the valve cover. Once I found them, it was plain and simple.
In addition, be sure to not over tighten the belt when reinstalling. The tensioner has markings on it for "old" and "new". DO NOT adjust past "new", as the car will sound like a jet engine, and the belt will not last for very long.
One more item that you may as well replace while you are in there is the cam position sensor if you have not already, as there have been issues with them, and the timing housing has to be opened to get to it

Posted on May 22, 2009

stevenhurc
  • 450 Answers

SOURCE: Where is the timing mark for the camshaft on a 2000 Daewoo Lanos?

single cam or twin?

466b3f3.jpg 1f27bcc.jpg

Posted on May 28, 2009

  • 121 Answers

SOURCE: 98 daewoo lanos ignition timing appears to be

try the distributor maybe it needs reset with the timing

Posted on Jun 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine timing belt 1600 daewoo lanos


It connects the crankshaft to the camshaft, which controls the valves that let the air fuel mix in and the exhaust out of the cylinders

Apr 14, 2010 | 2000 Daewoo Lanos

1 Answer

What does a P0342 code mean?


hallo
P0342 code means: camshaft position sensor- low imput. Check wiring (short to earth), if OK change camshaft position sensor.
Marko

Oct 08, 2009 | 2002 Daewoo Lanos

1 Answer

Crank pulleys on lanos taken off son cannot


hi, i believe you mean camshaft pulleys if so then the pulley with oblong holes goes on the camshaft nearest the front of the car

Sep 15, 2009 | 1999 Daewoo Lanos

1 Answer

CAMSHAFT


on single cam engine its inlet manifold side just behind cam gear rear cover bolted into cam box cover
twin cam its behind cams in middle front of engine in centre of rocker cover remove cover over h.t.leads this one is eazy but tricky due to bolt inside cam belt cover

Jun 28, 2009 | 1999 Daewoo Lanos

1 Answer

Locating camshaft positioning sensor on 2000 Daewoo Laganza


hi,
it is under the upper timing belt cover between the camshaft gears. According to the manual touching anything related to timing belt requires removing million parts including right front wheel. I suspect this might be an overkill just to remove upper timing belt cover.

So my advice would be to get it done by some mechanic as u will not be able to do it and may damage other parts also.

Thanks!
Sandy

May 18, 2009 | 2000 Daewoo Lanos

Not finding what you are looking for?
2000 Daewoo Lanos Logo

Related Topics:

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...