Question about 1991 Mazda MX-6

Open Question

Change engine need advice on removing axles,prior to removing engine

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove 3.8l engine and transmission?


The procedure is fairly detailed and likely your best bet would be to get a Hayes manual to ensure you perform all steps properly. In simplistic terms, you will need to place the front of the car on jackstands, remove the hood, remove the front drive axles. Disconnect all wiring harness and accessories from the engine. You will likely want to remove the A/C compressor from the engine without disconnecting any hose connections so that you will not have to have the A/C recharged. Drain transmission and radiator before starting. Getting a manual is the best advice I can give you.

Jun 27, 2015 | 1994 Buick Park Avenue

1 Answer

CANT FIND THE STARTER


good luck to change the starter you gotta take off the front axle its so dumb u cant get to it unless you do that. good luck.. my advice take it into a mechanic. u really do have to remove the whole front axle

Sep 01, 2012 | 2000 Acura 3.5RL

1 Answer

Getting to the alternator to change it


To get to the alternator you will need to remove the pass/side tire and also the fender well cover then dissconnect the neg battery terminal,next is to remove the belt, you will need to remove the nut from the lower balljoint and seperate the spindle from the lower control arm this is so the axle can be removed. next is to remove the two nuts holding the axle bearing plate to engine bracket then remove axle, then you will be able to remove the alternator bolts and the connections to remove alternator , the alternator will come the area where the axle was.

Jun 25, 2011 | 2004 Mazda Tribute

2 Answers

How d i change a clutch in a hyundai excel 1994


We start by removing front Constant Volocity Joints then dropping the transmision to access the cluch assembly then we remove the pressure plate then clutch disk is removed be advized since your replacing the cluck replace hardware too e.g. clips and thrust bearing and pilot bearing to complete the job! good luck!

Sep 02, 2009 | 1994 Hyundai Excel

1 Answer

I need yo know how to replace the cv joint and


remove axle nut,seperate balljoint from control arm,usually a good whack with a hammer on the control arm near the balljoint will free it,pry control arm down to remove knuckle assy, remove roll pin from inner axle joint now you can remove axle,most of the time the inner joint boot tears this is called the d-o-j {double offset joint} replace this boot as well,my suggestion is consider replacing axle with reman depending on mileage 100k or more.remember when reinstalling axle splines need to be lined up on inner shaft so roll pin goes in without problem good luck

Jul 18, 2009 | 2001 Subaru Forester

1 Answer

How to replace bearing


There is a vacum switch in the transfercase on the drivers side. you can get to it with a wrench, but it will make you work for it. Part store is like $45.00 GM like $90.00, Same part.
Rear bearing. remove the differental cover and drain fluid. Remove the C Clip that hold the Axle in. Slide the Axle out and inspect to see if you need a new one. High mile axle has a worn grove where the bearings are and changing the bearing alone does nothing. You ight get away with a finding a bearing to match your axle if it's worn. 
Remove the oil seal and then the bearing from the axle tube. 
In-stall in revers, note use lots of lube on the seal and be careful not to nick the seal and bearing. 
Fill differental with oil and run around the block, not hard and re-check the fluid. May want to go with syntetic oil or add lucus. Less maintance of oil changes to differental.
Good luck and hope this help.

Apr 03, 2009 | 1994 Chevrolet S-10 Blazer

1 Answer

Do i need to remove trans-axle to install engine


lower subframe its easy to do and drop engine out the bottom onto the floor

Jan 25, 2009 | 2001 Ford Focus

2 Answers

Not sure if this is the proper way to respond on this website.


Glad to provide the advice. That is what FIxYa is all about. The graciousness of a FixYa rating for my assistance would be greatly appreciated.

Dec 13, 2008 | 1999 Toyota 4Runner

1 Answer

Same problem


The bleed valve is located on the back side of the back plate of the axle. Try bleeding the system.

Jun 11, 2008 | 1998 Chevrolet Cavalier

Not finding what you are looking for?
1991 Mazda MX-6 Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

77201 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8743 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...