Question about 1984 Toyota Cressida

Open Question

1984 toyota cressida location of data link connector

Where is the data link connector so I can plug the OBD tool

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1861 Answers

SOURCE: Where is the On Board Diagnostic (OBD) connector on the car.

It is under the dashboard, driver side. White, oblong female connector. One row of pins not as long as the other.

Posted on Sep 17, 2008

  • 39 Answers

SOURCE: 1989 tOYOTA CRESSIDA sAPRK PLUGS WELLS. OIL IN THE SPARK WELL

You definatly need to replace your Spark Plug Tube Seals. Its not very difficult to do yourself. They should cost you about 4 dollars each at your local auto store.

If this is not fixed soon, it will cause more problems. Your O2 sensors will not read correctly because they will be coated in carbon.

Posted on Feb 24, 2009

  • 112 Answers

SOURCE: Where is the fuel filter located in 1984 Toyota Cressida

The fuel filter is in the engine compartment, rear of passenger side.

You may have prime the pump:
remove the gas cap, underhood, loosen a fuel connector, wrap the loosened connector with a shop rag to catch the fuel and crank the starter a few seconds, do not let the engine run. Check the rag for fuel, if gasoline has been delivered: Tighten the connector and fuel tank cap, properly dispose of the rag.

Posted on Jul 10, 2009

  • 2841 Answers

SOURCE: my 1992 toyota 4x4 truck has no power to fuel

Check the fuel pump relay.

Posted on May 01, 2010

  • 6 Answers

SOURCE: where is the OBD connector on a 2003 toyota highla...

It is located on the bottom of the Driver's side dash, below and to the left of the steering wheel. The connector is recessed about an inch and has a black cover that has "OBDII" imprinted on it.

Posted on Jun 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the obd II fuse located on a 2005 gmc yukon?


obd II fuse located ???? Or do you mean fuse for DLC - the connector under the dash that you plug the scan tool into ? GIG LTR fuse 15 amp under hood fuse box

Mar 30, 2017 | 2005 GMC Canyon

1 Answer

Where do i find the 31 vaf sensor curcuit on a 4s camry engine


Toyota Camry Cressida OBD Trouble Codes -

www.troublecodes.net/toyota/toyota-camry-cressida/
Get Help at BAT Auto · Get an ALLDATAdiy Repair Info Subscription ... Toyota Camryand Cressida have two separate diagnostic connectors and two separate diagnostic modes which both provide ... 92-95 Camry 2.2L Engine Code: 5S-FE ... 31, Volume air flow (VAF) sensor-Cressida -circuit, Wiring, VAF sensor, ECM.

Nov 13, 2015 | 1998 Toyota MARK II

1 Answer

1984 toyota cressida blower fan fuse location


It should be in the driver side in the dash around the steering wheel left side or under

Nov 21, 2011 | 1984 Toyota Cressida

1 Answer

I am looking for port to use OBD II tool I can not seem to find it. Any idea where I can find it?


On GM and Fords it's on the lower left hand corner of the dashboard, underneath the dash. You may have to look closer to find it.
There may be a plastic cap on it concealing it from view.

It should be there:

Diagnostic Link Connector Fig. 1: The OBD-II compliant Data Link Connector (DLC) is located under the driver's side of the instrument panel 91144p39.jpg
Fig. 2: A Tech 1® , or equivalent scan tool must be used to retrieve codes from the 16-pin DLC connector 88254gc8.gif
These vehicles are equipped with a Data Link Connector (DLC) which is the 16-pin connector that you attach the scan tool to read and/or clear Diagnostic Trouble Codes (DTCs). The DLC is located under the driver's side of the instrument panel. prev.gif next.gif

Nov 12, 2010 | 1999 Chevrolet Malibu

1 Answer

Looking for the OBDll connector for a 1996 Toyota Corolla ll Windy Model with a1N-T, 1453 cc turbo diesel engine. Steering wheel is on the passenger side of the car. Need this info for a friend. He has...


Look under the dash near where the steering wheel is usually located (on the driver's side).

Was this vehicle marketed in the U.S.?
1996-97 MODELS NOTE: These models require the use of the Toyota's hand held scan tool or an equivalent OBD II compliant scan tool.
  1. Prepare the scan tool according to the manufacturers instructions.
  2. Connect the OBD II scan tool, to the DLC3 under the instrument panel. The DLC3 on the 1996-97 models is located on the drivers side under the dash 88274pa2.jpg
    NOTE: When the diagnosis system is switched from the normal mode to the check mode, it erases all Diagnostic Trouble Codes (DTC) and freeze frame data recorded. Before switching modes, always check the DTC and freeze frame data and write them down.
  3. Turn the ignition switch to the ON and switch the OBD II scan tool switch on.
  4. Use the OBD II scan tool to check the DTC and freeze frame data. Write them down.
  5. Compare the codes found to the applicable diagnostic code chart. If necessary, refer to the individual component tests in this section. If the component tests are OK, test the wire harness and connectors for shorts, opens and poor connections.
prev.gif next.gif

Oct 05, 2010 | 1996 Toyota Corolla

2 Answers

How to change a throttle position sensor on a 94 ford f150 5.0 4x4


How to Replace a Throttle Position Sensor
(DIY & Save up to $135.75 ) - Time: 2.1 hours

Parts:
1. Throttle Position Sensor - $ 55.44

Tools:
1. Scan Tool
2. Screwdriver
3. Multimeter

Procedure:
1. Locate the OBD data link connector (DLC). Refer to your owner’s manual for the specific location.
  • Tip: The OBD-I data link connector is usually located in the engine compartment near the battery or the fuse box. The OBD-II connector (post 1995 cars) is usually located beneath the instument panel next to the steering column.
2. Turn your key to the“ON” position. Do not start the engine.

3. Plug your scan tool into the OBD data link connector. Turn on the scan tool and select the appropriate steps to read the diagnostic trouble code (DTC).

    6db8845.jpg

Scanner plugged into OBD-II data link connector.
  • Tip: The OBD-II diagnostic trouble code (DTC) is a 5 character alphanumeric code. The first digit is a letter that indicates the component group, the second digit is OBD mandated or manufacturer specfic, the third digit is a subgroup, and the fourth and fifth digits define the component and basic problem.
  • 4. Locate the throttle position sensor.
6182d26.jpg

  • Throttle position sensor

  • 5. Disconnect the electrical connector from the throttle position sensor.
fc565b1.jpg

  • Electrical connector removed
6. Test the resistance of the throttle position sensor (TPS) with a digital multi-meter. If the resistance is out of specifications, the TPS must be replaced.
  • 7. Remove the throttle position sensor.

  • d3a8007.jpg

    Removing sensor mounting screws

    8. Install the new throttle position sensor. Tighten the mounting screws and attach the electrical connector.
  • 9. Erase the diagnostic trouble code (DTC) with the scan tool using the“delete” or“erase” command. Road test your vehicle to see if the check engine light returns.
fde01cf.jpg

    Check engine light

  • Tip: If the check engine light returns, repeat the diagnostic process for additional DTCs or take your vehicle to a certified repair shop.
Direct OE replacement

Hope helped with this. Good luck (remember rated this help).

Nov 05, 2009 | Ford F-150 Cars & Trucks

2 Answers

Where do i find the dlc plug


PLEASE DON'T FORGET TO RATE!!!! Data Link Connector OBD II Systems use a standardized test connector called the Data Link Connector (DLC). It is located beneath the instrument panel somewhere between the left end of the instrument panel and 12 inches (300 mm) past the vehicle centerline.
The DLC is located out of the sight of vehicle passengers, but should be easily viewable by a technician from a kneeling position outside the vehicle. The DLC is rectangular in design, capable of accommodating up to 16 terminals and has keying features to allow for easy connection. The DCL and Scan Tool connector have latching features that ensure the Scan Tool connector will remain mated when properly connected. Some common uses of the Scan Tool are:
  • To identify and clear any stored diagnostic trouble codes
  • To read the serial data stream information (e.g., PID data)
  • To perform Enhanced Diagnostic Tests (bi-directional Scan Tool)
96d7723.gif
Data Link Connector Graphic

Nov 01, 2009 | 2002 Oldsmobile Alero

1 Answer

Where is the fuel filter located in 1984 Toyota Cressida


The fuel filter is in the engine compartment, rear of passenger side.

You may have prime the pump:
remove the gas cap, underhood, loosen a fuel connector, wrap the loosened connector with a shop rag to catch the fuel and crank the starter a few seconds, do not let the engine run. Check the rag for fuel, if gasoline has been delivered: Tighten the connector and fuel tank cap, properly dispose of the rag.

Jul 10, 2009 | 1984 Toyota Cressida

2 Answers

Where is the obd plug in on a 2002 Nissan Xterra ?


It should be under the drivers side dash board. 1/2in x 1in black connector.

Mar 13, 2009 | 2002 Nissan Xterra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...