Question about 2002 Toyota Avalon

Open Question

POWER MIRROR MEMORY MODULE 2002 TOYOTA AVALON REPAIR OR REPLACE

MEMORY DOES NOT WORK FOR POWER SEATS OR POWER MIRROR

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1861 Answers

SOURCE: I need to remove the

Pull up on the lower front edge to dislodge the seat from the clamps that holds the seat to the floor. Pull hard, if the seat has never been removed. the clamps will be tight. Once the seat bottom is out, you will be able to see the bolts that holds the rear seat backs onto the body.

Posted on Nov 12, 2008

Ad
  • 76 Answers

SOURCE: Replacing 2000 toyota avalon fog light bulb

o easy enough just jack frontcar up use jackstand for safety now loo up under the bumper where fog lights sit depending on style fog light u might need to pull the whole assembly out or just twist the bulb not a hard task once u see it from underneath it is pretty easy

Posted on Dec 02, 2008

  • 75 Answers

SOURCE: My 99 Toyota Avalon horn does not make any sound.

the horn in toyotas car have permanent positive curent+ at terminal wat you ned is the curent negative -- that come in contact when you presse the steering colum in the midle this is acctualy the switch you loking for oyu most have a bad contact in that steering if you are going to remove the air bag to have access to that mechanism be carreful not to bang or dammage the air bag it my inflate and hurt you badely nicolas

Posted on Dec 22, 2008

messstat
  • 365 Answers

SOURCE: Toyota Avalon Rear View Mirror

The "button" or metal disc you speak of comes off the mirror assembly by loosening the small torx/allen screw hidden under the sheath that covers the mirror "stalk"...follow the rearview mirror directions, to the letter. If you cannot get the button out...carefully clean the face of that button off using a safety razor, being careful not to nick or abrade the button...make sure the same spot on the windshield by marking it with a felt tip marker on the outside of the windshield BEFORE you clean the residue off the glass!
Good Luck

Posted on Jun 22, 2009

  • 1986 Answers

SOURCE: How do I replace a

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then the cover for the mirror housing should pop off and you just need to remove the bolts holding the mirror on

Posted on Aug 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Memory seats adjust on there own as well as mirrors


BCM has nothing to do with this function , MMM - memory mirror module !
Memory Mirror System Operation
The MMM is capable of storing mirror position for 2 different drivers. Mirror position is determined by both horizontal and vertical position sensors in each of the power mirrors. The MMM supplies a reference voltage and a low reference to these sensors and determines mirror position through the horizontal and vertical position signal circuits.
The MMM receives power through the battery supply voltage circuit and the MIR/LOCK fuse and a constant ground source. Any time that battery voltage is disconnected and then connected from the MMM, the MMM will enter the mirror relearn mode. The mirror relearn mode can also be commanded using a scan tool. Refer to Memory Mirror Module Learn for further information.The memory switch receives power through the battery supply voltage circuit and the MIR/LOCK fuse. The MMM upon receipt of a memory switch signal input, a class 2 message from the SIC or a class 2 message from the PCM indicating that the transmission is in park, will then supply battery voltage and ground to the appropriate power mirror motors through the mirror motor control circuits to move the mirrors to the predetermined positions.

DTC B1586, B1596, B1616, or B1626
The mirror horizontal and vertical position sensors are potentiometers. The Memory Mirror Module (MMM) provides these sensors with a 5 volt reference circuit and a low reference circuit. The MMM monitors the horizontal and vertical position sensor signal circuits which change values based on mirror position. These voltage values are used to determine mirror position and can be set into memory. When the MMM receives a memory recall request, the MMM will control the power mirror to the memory position based on the horizontal and vertical position sensor signal values.

Install a scan tool.
Turn ON the ignition, with the engine OFF.
With the scan tool, observe the mirror horizontal and vertical position parameters in the Memory Mirror Module (MMM) data list.
Operate both the left and right mirrors through the full range of movements.
Does the scan tool indicate that the left and right mirror horizontal and vertical position parameters are within the specified range?

Memory Seat System Components
The memory seat system consists of the following components:
• Power seat switch assembly
• Memory recall switch assembly
• Horizontal adjuster motor
• Front vertical adjuster motor
• Rear vertical adjuster motor
• Recline adjuster motor
• Memory seat module
• Memory mirror module
• SEAT 25A circuit breaker
• MIR/LOCK 3A fuse

Your best bet , take it to a qualified repair shop !

May 23, 2017 | 2002 Cadillac Escalade

1 Answer

I have a 2002 gmc envoy xl. the heat and seat and mirrors work fine, however every time i turn the car on or off the seat shifts all the way forward and the mirrors tilt in. to solve some of the...


Memory Seat System Components
The memory seat system consists of the following components:
• Power Seat Switch
• Seat Horizontal Motor
• Seat Front Vertical Motor
• Seat Rear Vertical Motor
• Seat Recliner Motor
• Driver Seat Module
• Memory Seat Switch

It's not the module , probably sensor supplying bad info to the module.

Memory Set/Recall Operation
The driver seat adjuster motors are equipped with potentiometer type position sensors used by the driver seat module to determine the seat position. The position sensors are supplied with 5-volt reference and ground circuits from the driver seat module. The position sensor signal circuits are referenced from ground within the driver seat module. The signal circuit voltage levels monitored by the driver seat module range from 0.39 - 4.58 volts and are determined by the wiper locations on the resistors within the motor position sensors. The position sensor circuit voltage levels are used by the driver seat module to determine the seat position when storing or recalling memory position settings.
The memory recall switch assembly on the driver's door provides inputs to the driver door module. Battery voltage is supplied to the memory recall switch assembly from the driver door module. When a memory recall 1, 2, or EXIT switch is pressed, the switch contacts close the appropriate switch signal circuit to the battery voltage supply circuit within the memory recall switch assembly. When the driver door module receives active switch signals from the memory recall switch assembly, the appropriate commands are sent to the driver seat module using the Class 2 Serial Data circuit.
Memory seat recall operation is allowed only with the transmission selector lever in the PARK position while the ignition is on. The transmission selector lever position data is provided to the driver seat module by a message through the Class 2 Serial Data circuit.

Your best bet , take it to a qualified repair shop and have it checked for DTC'S - diagnostic trouble codes .
Install a scan tool.
Observe the switch parameter for which the DTC has set in the seat module Inputs/Outputs data list.
Does the scan tool display Inactive?
DTC B1735, B1740, B1745, B1750, B1755, B1760, B1815, or B1820
DTC B1825, B1850, B1860, B2355, B2365, or B2375
The driver seat adjuster motors are equipped with potentiometer type position sensors used by the driver seat module to determine the seat position. The position sensors are supplied with 5-volt reference and ground circuits from the driver seat module. The position sensor signal circuits are referenced from ground within the driver seat module. The signal circuit voltage levels monitored by the driver seat module range from 0.39-4.58 volts and are determined by the wiper locations on the resistors within the motor position sensors. The position sensor circuit voltage levels are used by the driver seat module to determine the seat position when storing or recalling memory position settings.

$316.00 from doorman

Aug 15, 2017 | GMC Cars & Trucks

2 Answers

Toyota 2007 avalon rear defroster not working. Mirror defrost is working. What is wrong?


First check all fuses, second check for 12v power at the connector to th rear window, a test light or volt meter on dc voltage,if there is power use an ohm meter to check the window grid with the power connector disconnected.if open the connection is either open or bad. if there was no power at the connector check the power from switch all the way back to the window

Feb 28, 2013 | 2007 Toyota Avalon XLS

1 Answer

How do I replace a 2007 Toyota Avalon drivers side power seat switch w/o memory seat?


First of all, air bag sensors are not under the seats, so don't worry. Next, the switch working at certain times means that perhaps you do not have to replace it. The cold switch contacts are slightly corroded from moisture condensing on them. When the car warms up, the contacts are "clean" and make good electric contact. Choose: live with a little inconvenience or start messing with the switch to clean off the electrical contacts inside with electrical contact cleaner which requires removing the switch and opening up its insides.

Jan 23, 2013 | 2007 Toyota Avalon

1 Answer

2002 Toyota Avalon intermittent setting on wipers not working. In that setting the wipers stay on continuosly and when setting the wipers to the off setting they stay where ever the blades are at the time...


The problem is a broken part in the module which is inside the wiper motor. As far as I know, the part is not available, and you must replace the entire wiper motor to repair the problem

Dec 13, 2010 | 2002 Toyota Avalon

1 Answer

The memory power seat feature does not work on our 2002 avalon.


On GM products this is usually controlled by the remote being close to the ignition switch. The remotes have number 1 and 2 on the back of them. When it does not work do you have the remote close and do you have one remote for you and one for the other driver? Also, some cars have buttons to run this feature. Mom's stopped working when she got a remote start added to the car. Let us know if you find an answer.

Mar 06, 2010 | 2002 Toyota Avalon

1 Answer

Power mirrors, driver power seat, adjustable pedals all don't work... checked fuses and all ok... Any suggestions?


it sounds like the driver seat module. It controls all of these items.
buy used at car-part.com. look on page with * for lowest price.
buy new at discount at tascafordparts.com

  • The memory mirror is inoperative
  • Driver seat module (DSM).
  • Circuitry.
  • CJB fuse 3 (7.5A).
  • Exterior mirror motor.
  • Mirror control switch.


  • The memory seat is inoperative
  • Circuitry.
  • Seat control switch.
  • Seat track.
  • DSM.
  • PDJB Fuse 109 (30A).
  • Power seat motor.


  • Adjustable brake pedal does not operate correctly — does not operate using the adjustable pedal switch
  • Battery junction box (BJB) fuses:
    • 109 (30A).
  • Circuitry.
  • Switch.
  • Adjustable pedal motor.
  • Driver Seat Module (DSM

Oct 02, 2009 | 2003 Ford Expedition

1 Answer

My side mirros dont work


The exterior mirrors:
  • are controlled by power controls on the LH front door trim panel.
  • are of a foldaway design.
  • may contain turn signal indicators.
  • may be heated when the heated back window glass is activated.
  • may have a programmable recall memory option.
Driver Seat Module
The power driver seat and power exterior mirrors are controlled by the driver seat module (DSM) only when the vehicle is equipped with the programmable/recall memory option.
---------------------------------------------------------------------
Power Exterior Mirror Operation
The power exterior mirrors are controlled by the DSM and are operational all the time, whether the ignition switch is on or off. Using the power exterior mirror switch, the driver can adjust the driver and passenger exterior mirrors four ways.
-----------------------------------------------------
Visual Inspection Chart Mechanical Electrical
  • Exterior mirror(s)
  • Interior mirror
  • Central junction box (CJB) fuse
  • Circuitry
  • Exterior mirror control switch
  • Exterior mirror motor
  • Interior mirror
  • Driver seat module (DSM)
  • Memory set switch


----------------------------------------------------------------------------------


  1. If the vehicle is equipped with memory exterior mirrors and the concern remains after the inspection, connect the diagnostic tool to the data link connector (DLC) located beneath the instrument panel. Select the vehicle to be tested from the diagnostic tool menu.
    • Check to make sure the program card is correctly installed.
    • Check the connections to the vehicle.
    • Check the ignition switch position.
-------------------------------------------------------------------------------------
  • The mirrors are inoperative
  • Circuitry.
  • Central junction box (CJB) fuse.
  • Exterior mirror control switch.


Apr 07, 2009 | 2003 Lincoln Navigator

2 Answers

DRIVER POWER SEAT 1996 TOYOTA AVALON WONT


Check all your fuses in the fuse box. A fuse must have cut off.

Mar 18, 2009 | 1996 Toyota Avalon

1 Answer

Front power seat doesn't have power


check power going to seat buttons if there is power then the seat buttons need to be replaced/ buttons are only 5-10.00 a piece then replace if it there is no power going to buttons then its the motor/ Please rate my response thank you very much

Dec 29, 2008 | 2002 Toyota Avalon

Not finding what you are looking for?
2002 Toyota Avalon Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8560 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...