Question about 1996 Ford Contour

1 Answer

96 ford contour blower fan removal

I cannot get blower motor out ,am able to turn plastic housing 360 degrees but it will not drop out, I'm frustrated!

Posted by on

  • Lisa Young
    Lisa Young Sep 26, 2016

    There is a clamp that you have to push in it on the rim of the edges and all the notches has to be Alined for it to fall out

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 276 Answers

You remove the heater blower by removing the bottom cover of the Glove Compartment. Then you will see The heater blower housing. Then you will see like a black clip you need to lift. Then You simply turn clockwise and bingo its off. To install just do the same thing except in reverse mode. Good Luck!!

Posted on Nov 19, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace a/c heater fan motor


  • Disconnect the negative battery cable.
  • Disconnect the blower motor lead connector from the wiring harness connector.
  • Remove the blower motor cooling tube from the blower motor.
  • Remove the four retaining screws.
  • Turn the motor and the wheel assembly slightly to the right so that the bottom edge of the mounting plate follows the contour of the wheel well splash panel.
  • Lift up on the blower and remove it from the blower housing.
  • Installation the new blower motor by reversing the removal steps.
  • Connect the negative battery cable.
  • Jan 03, 2011 | 2006 Chevrolet HHR

    1 Answer

    How do i replace the fan blower motor


  • Disconnect the negative battery cable.
  • Disconnect the blower motor lead connector from the wiring harness connector.
  • Remove the blower motor cooling tube from the blower motor.
  • Remove the four retaining screws.
  • Turn the motor and the wheel assembly slightly to the right so that the bottom edge of the mounting plate follows the contour of the wheel well splash panel.
  • Lift up on the blower and remove it from the blower housing.
  • Installation the new blower motor by reversing the removal steps.
  • Connect the negative battery cable.
  • Dec 28, 2010 | 1991 Chevrolet Caprice

    1 Answer

    1993 ford taurus blower motor dont work


    check the fuses if thats not it then change the blower motor instructions below, not that hard to do!
  • Disconnect the negative battery cable.
  • Disconnect the blower motor lead connector from the wiring harness connector.
  • Remove the blower motor cooling tube from the blower motor.
  • Remove the four retaining screws.
  • Turn the motor and the wheel assembly slightly to the right so that the bottom edge of the mounting plate follows the contour of the wheel well splash panel.
  • Lift up on the blower and remove it from the blower housing.
  • Installation the new blower motor by reversing the removal steps.
  • Connect the negative battery cable.
  • Dec 27, 2010 | 1993 Ford Taurus

    1 Answer

    How to fix a 2001 ford escape blower motor


  • Disconnect the negative battery cable.
  • Disconnect the blower motor lead connector from the wiring harness connector.
  • Remove the blower motor cooling tube from the blower motor.
  • Remove the four retaining screws.
  • Turn the motor and the wheel assembly slightly to the right so that the bottom edge of the mounting plate follows the contour of the wheel well splash panel.
  • Lift up on the blower and remove it from the blower housing.
  • Installation the new blower motor by reversing the removal steps.
  • Connect the negative battery cable.
  • Dec 16, 2010 | 2001 Ford Escape

    1 Answer

    Fan for ac and heater won't come on but can feel warm and cool air


    change out the blower motor instructions below
  • Disconnect the negative battery cable.
  • Disconnect the blower motor lead connector from the wiring harness connector.
  • Remove the blower motor cooling tube from the blower motor.
  • Remove the four retaining screws.
  • Turn the motor and the wheel assembly slightly to the right so that the bottom edge of the mounting plate follows the contour of the wheel well splash panel.
  • Lift up on the blower and remove it from the blower housing.
  • Installation the new blower motor by reversing the removal steps.
  • Connect the negative battery cable.
  • Dec 14, 2010 | 2000 Ford F150 Flareside SuperCab

    1 Answer

    How do I remove the heater blower motor on a 1995 ford contour. It has the 2.0 L 4 cyl.


    Blower Motor Switch Resistor Assembly REMOVAL & INSTALLATION Fig. 1: Remove the resistor assembly by gently popping it out of the evaporator housing using a screwdriver 91056g24.gif
    1. Disconnect the negative battery cable.
    2. Remove the push pins and remove the upper footwell panel from under the passenger side of the instrument panel.
    3. Unplug the connector from the blower motor resistor assembly.
    4. Insert a screwdriver approximately 0.2 inch (5mm) under the edge of the resistor assembly to disengage it from the evaporator housing.
    5. Remove the resistor assembly. To install:
    6. Position the resistor assembly into the housing and snap it into place.
    7. Attach the resistor connector.
    8. Install the upper footwell panel.
    9. Connect the negative battery cable. prev.gif next.gif

    Jul 31, 2010 | 1995 Ford Contour

    6 Answers

    1998 Ford Contour. The heater blower stopped suddenly. I checked all the fuses, good. I removed the blower and hooked it to 12 volts. Whoosh! It almost spun out of my hand. I checked the plug into the...


    I dont know what these other guys are saying..I think they snif the glue!!! YOUR BLOWER FAN ASSEMBLY CAN EASILY BE REMOVED !!
    1. Remove the wire
    2.Find the "tab on the housing and pull it down while rotating the fan housing counter clockwise. This will remove the fan assembly. Plage 12 volts on the contacts to test the motor. If it works then the resister pack is blown. On the fan housing (near firewall ) you will see a plug going into a square looking box with a screw in it. Remove the wire then remove the screw to remove the resistor pack.. A new resistor pack is around 20 dollars at a ford dealer. Hope thie "FREE" info helps!

    Feb 24, 2010 | 1998 Ford Contour

    1 Answer

    Heater of my 1999 ford contour is not working. is there a fuse i can replace to make it work?


    There is a fuse under the steering wheel area, also there is a heater conrol under the passenger side dash on the left side of the blower motor. 1 screw holds it in the plenum(heating duct) there is a 4 wire plug going to it. You can check the actual blower motor for operation by putting 12 volts to it. To remove it there are two tabs on either side of the housing.Remove the wire first. Push the tabs up together and turn the fan housing to remove it. You now will have the whole fan in your hands. Using a wire jump from a 12v source(car battery works) to test the fan.2 wires reqd for + and-. if the fan does not function it may need replacing or just lubrication.

    Jan 09, 2010 | 1999 Ford Contour

    Not finding what you are looking for?
    1996 Ford Contour Logo

    Related Topics:

    385 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    60960 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Fordexpert

    Level 3 Expert

    5331 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...