Question about 1990 Toyota 4Runner

1 Answer

My1990 4runner will not roll in nutral and my key wont release from ignition. Unless. I disconnect. My battery. Does any one have any ideas. What this could be.better

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 2,431 Answers

You have a problem with a shift cable interlock that is binding.For your particular year there is a new version due to the high failure rate of these cable. Part # 33880-35011

Posted on Feb 24, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will anti theft by pass module over really bypass the theft system


My mechanic disconnected the security section because my key I use to start the car had the security spot on the key was loose and would not work in the ignition It was going to cost a lot for a new set of keys so he took the security section out for a lot less. As he said an older car does not need security.

Jul 04, 2017 | 2002 Ford Explorer

1 Answer

Replacement ignition key 1999 pontiac bonneille


Just the key or the whole lock cylinder with key ?

Removal Procedure
Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.
Disconnect the battery negative cable.
Disable the SIR system. Refer to Disabling the SIR System
Position the steering wheel half way between the upper and lower tilt stops (if necessary).
Remove the steering wheel. Refer to Steering Wheel Replacement .
Roll back the shift lever seal from the upper and the lower shrouds.
Remove the tilt wheel lever (if necessary). Refer to Tilt Lever Replacement - On Vehicle .
Remove the 2 TORX® screws from the lower steering column shroud.
Remove the lower steering column shroud.
Remove the 2 TORX® screws from the upper steering column shroud.
Lift the upper steering column shroud to gain access to the lock cylinder access hole.
Using a bent tip awl, insert the tip into the ignition lock cylinder access hole.
Turn the ignition lock cylinder to the START position.
Using the bent tip awl, push down on the ignition lock cylinder retaining pin.
Release the ignition lock cylinder to the RUN position.

Remove the ignition lock cylinder from the lock module assembly by pulling the ignition lock cylinder away from the steering column.

There may be a video on youtube .

Feb 23, 2017 | Pontiac Cars & Trucks

1 Answer

After having disconnecting the battery in my Chevy


The turn signal clicking sound comes from the driver radio speaker .Disconnecting battery without using back power supply can cause problems .Does the radio show loc ?
Battery Disconnect or Replacement Problems
Being able to roll down the windows with the key off is a function of RAP - Retained Accessory Power .
Retained Accessory Power (RAP) is a power mode that permits the operation of selected customer convenience items for 10 minutes after the ignition switch is turned OFF. RAP power mode is enabled by the BCM.- body control module .Disconnecting the battery caused something to power down an not wake up . The dealer should have been able to hook up Tech 2 scan tool an tell that . Without looking at factory service info . i believe the BCM sends a wake up signal to the radio , that's just a guess . I would need to know the year of your vehicle to check .

Jan 07, 2018 | Cars & Trucks

1 Answer

85 corolla wont crank


What about the ignition switch not the key switch, ignition switch or ignition module?

Jan 26, 2013 | 1985 Toyota Corolla

1 Answer

Keys stuck in the on position and no power


I had the same problem with my S10 blazer. The ignition needs
replaced, or the nutral safty switch needs replaced.

Jul 25, 2012 | 1999 GMC Jimmy

1 Answer

I turn my key to start the car, lights and radion come on, but the car wont turn over at all. I have already cheked the battery and it is fully charged.


does it click?
if so then youv got abad battery conection
if not cheak the nutral safty switch, and then the starter
then the ignition switch

Jun 24, 2009 | 2004 Chrysler Crossfire

2 Answers

Car wont start


check nutral safety switch,you have power on the starter, now is ignition to starter power

Apr 11, 2009 | 1993 Toyota Camry V6

Not finding what you are looking for?
1990 Toyota 4Runner Logo

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...