Question about 1995 Ford Ranger Supercab

Open Question

Timing belt change for 95 ford ranger 2.3L - 1995 Ford Ranger Supercab

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: 99 ford ranger timing belt


Using the same 13mm socket, remove the bolt that you found under the a/c compressor. Look down and to the right of the bolt that you just removed, and you will see two more bolts. Both are 13mm. Easiest way that I found was to go under the driver side tire well, and use 3/8 extensions to reach the two bolts. Once removed, the bracket and the power steering pump should be moved to the driver's side of the frame, and the a/c placed on top of the p/s assy.




Remove the bolts (6mm) that hold the timing belt cover in place. Gently work your way around the cover, and push the tabs in to remove the cover.


Use an impact wrench and 7/8 SAE socket to remove the crankshaft pulley. A SOCKET WRENCH WILL NOT WORK. Once removed, gently tap the pulley with a 2x4 (yes the wooden board) to remove. If you have a gear puller, use that. I don't own one.




Remove the old belt. Now for the alignment. Crank - sprocket on bottom. Use the bolt you removed, and a ½ drive wrench, with the 7/8 socket to turn the crank. Once the keyway is at high noon, leave it alone. Next, move the oil pulley sprocket until the diamonds are aligned. This should put the oil pulley at high noon, also. The camshaft should have a diamond and a triangle. The diamond should go to high noon, and the triangle should align with a triangle on the plastic behind the sprocket. YOU SHOULD REALLY CONSIDER CLEANING THE ENTIRE AREA BEFORE ALIGNING THE SPROCKETS. You cannot align the camshaft without locating the two index (triangle and diamond) marks.


You will also notice a tensioner for the timing belt. You will need to loosen the tentioner with a 13mm and 17mm wrenches. Loosen, then use a cheeter bar bar to move the tentioner over. Lock in place by tightening the tentioner bolts. Place the belt on the crankshaft, move to the oil pulley, then to the cam pulley. Release tentioner, then check the alignment. If correct, reverse the above removal plan, and you should be good.




Don't buy the Haynes manual. I fought with the instructions for this project, and the picture for the timing belt project doesn't show the two indexes for the cam sprocket.



Also, while you are doing this, you should replace the antifreeze if you haven't in the past two years.



Best of luck.

Posted on Jul 13, 2008

Ad
lobsterman72
  • 91 Answers

SOURCE: 1988 ford ranger

Though it's a bit late from when this question was asked... But... I replaced my timing belt before it broke. Like anything else on my 88 ford ranger it was the easiest thing! If your really carefull and remove the plugs! You must remove the plugs because of the compression that's there waiting to fire when you next start the car. Dissasemble the fan, fan cover, and the pulley and the plastic cover. Not exactly in that order, just what you need to access the belt. Score or mark or paint where one or two teeth of each pulley is in reference to a non moving part of the truck (you can rotate the whole thing to a convient setup by hand) make sure when you rotate the assembly it feels somewhat free you can see and feel that there is no tension on the belt in ANY area. When you have all the marks set up loosen the bolt holding the tensioner use a bar to move the tensioner out of the way just enough then tighten the bolt on the tensioner, that will keep it locked open while you simply and carefully slide out the belt then slide in the new belt keeping the marks 'still', just go slow and keep your eyes open. Maybe I just got lucky...But the theory is sound and worked for me.
Probably could use a diming light to make sure but I don't have one and the truck still runs fine. Oh and by the way... if you ever need to replace the heater core it'll take you all of 20 mins if you have even the basic of abilities and the right screw driver :)

Posted on Jun 27, 2008

  • 899 Answers

SOURCE: 1991 ford ranger not getting any spark

probably the coil , but have your alternator checked first

Posted on Oct 07, 2008

  • 33 Answers

SOURCE: removal and install timing belt 1994 ford ranger/

Depends on the engine.

Posted on Oct 10, 2009

  • 1757 Answers

SOURCE: what do the timing belt marks line up on a 94 ford

My apologies for the delayed response. I am going back to answer unanswered questions.
CLICK
on the following LINK. It has the Timing Belt & Mark(s) Diagrams you will need.
If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Again my sincerest apologies...
Thanks!

http://www.2carpros.com/car_repair_information/year/1994/make/ford/model/ranger/1994_ford_ranger_timing_belt_diagram_marks.htm

Posted on Mar 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

94mazdaB2300 2.3 Has No power,backfires,running rich.R&R plugs,wires,timing belt,coil pack,02 sensor,feedback sensor,massairflow,catalytic converter. Still runs bad


Check the vacuum hoses.

Search Results

    95 2.3L no power and backfire - Ford Truck Enthusiasts Forums

    www.ford-trucks.com > ... > Small Chassis Trucks > Ranger & B-Series Aug 16, 2010 - 95 2.3L no power and backfire Ranger & B-Series. ... Once the engine warms you get it out on the highway and it has no power, if you pump ... again it will stumble and backfire, when running at highway speeds and you try to ... More results from www.ford-trucks.com

Sep 13, 2015 | Cars & Trucks

1 Answer

Do I need to take off balancer to replace timing


Yes, and the timing cover behind that. Probably all accessories on the front of the engine. Watch bolt lengths. Sometime there are quite a few different lengths and placing them back incorrectly can cause damage.

Sep 21, 2014 | Ford Ranger Cars & Trucks

1 Answer

How do you change motor mounts on a 1990 Ford Ranger 2.3


Ford Ranger 2.3 rebuild part 3 "xTUPID BOLTS" - YouTube

? 2:55
www.youtube.com/watch?v=ZJ1jFK4weUE
Mar 28, 2011 - Uploaded by DirTyOhGee
89 Ford Ranger 2.3 Custom/Limited. Moving right along here, ...How to change the timing belt on a Ford 2.3L engine. - Duration: 29:59. by ...

Oct 05, 2012 | Ford Ranger Cars & Trucks

1 Answer

What its the right way to put on time ... a timing belt on a pick up ford ranger '97 engine 2.3


yeah just change the timingbelt in my 95 ranger and i get a on and off squealing sound 2.3l

Jun 15, 2010 | 1987 Ford Ranger

1 Answer

Trying to put timing marks wright on a1995 ranger


Your question states both 94 and 95 for model year.
94 and 95 ranger had a 2.3L.

  1. If not done:
    1. Loosen tensioner adjusting bolt.
    1. Using Camshaft Belt Tension Adjusting Tool T74P-6254-A, pry tensioner clockwise against spring tension as far as possible.
    1. Tighten adjusting bolt to hold tensioner in released position.
  1. Align crankshaft so number one piston is at TDC (top dead center) with crankshaft key pointing straight up and circle on crankshaft sprocket (6306) aligned with notch in engine front cover (6019) .
  1. Align triangle on camshaft sprocket with triangle on inner timing belt cover.
  1. Align diamond on oil pump sprocket with diamond on inner timing belt cover.

    Timing Mark Alignment

5f171ff.gif

Feb 27, 2010 | 1994 Ford Ranger Supercab

1 Answer

Timing belt broke on a 95 ford ranger.new belt


you have to line up the two marks on the gears and set the tension to the correct setting. then check the marks again. trial and error. i just did my timing belt on my ranger haha

Feb 18, 2010 | 1995 Ford Ranger Supercab

1 Answer

I NEED A TIMING DIAGRAM FOR A 95 FORD RANGER 2.3 liter SOHC L4 VIN ''A''


diagram for timing belt, if so need email address and is it 2wd or 4wd

Feb 05, 2010 | 1995 Ford Ranger Supercab

1 Answer

When do you change timing belt on 2002 Ford Ranger Pickup w/ 4-cyl 2.3, auto trans, with 85,000 miles?


It is recommended that you change the timing belt at 80000 miles, but I had one with over 200,000 miles that never had a problem.

Sep 24, 2009 | 2002 Ford Ranger Regular Cab

1 Answer

95 ranger 2.3l spark knock problem


Is this a manual trans in this truck, if so, try shifting down a gear. But yes a timing belt could cause this, but usually they wont run very well if the timing belt is that bad worn.

Jul 03, 2009 | 1995 Ford Ranger Supercab

Not finding what you are looking for?
1995 Ford Ranger Supercab Logo

Related Topics:

119 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...