Question about Ford Crown Victoria

Open Question

Having problems a/c stops working &cooling fan never stops 1999 crown victoria

Wen the car its running and u turn on the a/c works for a second then stops then the cooling fan never stops and the a/c never came back on what should i do thanks hope u can help me

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 58 Answers

SOURCE: 2006 crown victoria - no heat

I would change the thermostat in the vehicle first and go from there. Hope this helps......Dan

Posted on Jun 21, 2008

  • 740 Answers

SOURCE: Check engine light on 1999 Crown Victoria - CNG

Oxygen sensor -sensor #2 on Bank #1. If I fix ya leave me a fix ya comment. Good Luck

Posted on Dec 27, 2008

  • 1596 Answers

SOURCE: fuse box diagram

Locations In Case this Picture Doen not SHOW UP FOR YA --
WIPER Fuse ok Lookin at the box with the Round Circle In TOP RIGHT Corner Wiper is Number 2 Bottom from That Circle would be 2nd one from right Suppose to Be a 30 amp fuse Hopin this Helps Ya If so Please RATE Me AS High as You feel I Dererve Thank You and Good Luck with the CROWN VIC
Notes 78246312

Posted on Jan 31, 2009

  • 93 Answers

SOURCE: 2000 crown victoria serpentine belt installation

Accessory Drive Component Locationsa0011762.gif

Posted on Jun 09, 2009

teemossinmia
  • 265 Answers

SOURCE: serpentine belt squeaks on startup

You can not tighten the belt, it is held on by the Belt tensioner...it's located a little to the left side of the waterpump...now it maybe getting weak, or your belt may need to be replaced...Sometimes they look good, with no cracks, but they get worn and streched out over time..or it may look shiny..either one of those will cause it too squeak..

Posted on Dec 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My coolent fan turns off then car runs hot


I would check my relay's and or your fuses first. If thats not it, let it cool down and take it to Auto Zone or somewhere close to have a diagnostic readout done. Good luck.

Jul 29, 2014 | 2000 Ford Crown Victoria

1 Answer

Location of coolant temp sensor 2000 crown vic


If the sensor was the problem you would have a check engine light on, the fan is operated by the powertrain control module which controls a relay module. You must have the dealer run a scan of the system ans do an active test on the fan operation to determine what is wrong.

Sep 27, 2012 | 2000 Ford Crown Victoria

1 Answer

I am in saudiarab i have crown victoria 97 model it is working good but i have problum in air condition system when i run my car its running good no problum but when i start my air condition it is heating...


The air conditioning condenser creates a lot of heat when the a/c is on. The cooling fan is supposed to run the whole time the a/c is on to keep it cool. If the fan isn't on, the radiator will absorb this heat and cause your car to over heat. You should also check your coolant level. So, it sounds to me like your cooling fan isn't working.

Sep 13, 2011 | 1997 Ford Crown Victoria

1 Answer

My cooling fan stooped working ,my a/c stopped working and i checked all the fuses that are related to that circuit. 2006 crown victoria taxi package. all started off when you turn the key ,and the...


check your vlcm-variable load control module, located in front of the radiator (has fins, and has a large harness attached to it)-the harness may need to be tightened or the module itself may be bad-before to replace it swap relays for the AC with the ABS to see if it is just a bad relay.

Sep 12, 2011 | 2006 Ford Crown Victoria

1 Answer

I have 1999 Crown Victoria that the horn is not working i've checked the fuse & replaced the relay and still nothing.


try bypassing it with a wire from the + cable of the battery. if it works, your problem is elsewhere like in the steering wheel, broken or loose connection. if it doesn't work, replace the horn

Jan 13, 2011 | 1999 Ford Crown Victoria

1 Answer

The fan don't turn on?


If its a cooling fan, it could be
1-bad fan
2-bad temp sensor
3-bad electrical connection
A check for error codes will give you a start on identifying the source of the problem

Good Luck

Oct 05, 2010 | 1999 Ford Crown Victoria

1 Answer

Radiator fan in my 2003 crown victoria runs continuosly


No, the fan is supposed to come on only at certain temperatures.

Trace the wiring from the fan back, there should be a temp switch/relay in line. If there isn't,then someone has bypassed it and wired the fan to run when the car is running.

Jan 02, 2009 | 1999 Ford Crown Victoria

1 Answer

2006 crown victoria - no heat


I would change the thermostat in the vehicle first and go from there. Hope this helps......Dan

Jun 20, 2008 | 1999 Ford Crown Victoria

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...