Question about 1998 Jeep Grand Cherokee

Open Question

Water pump location on 1998 jeep grand cherokee

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

garyq1970
  • 73 Answers

SOURCE: change water pump

If you have any questions feel free to ask. Let me know if you dont get diagrams(happens sometimes)

0900c1528004319d.jpgReverse rotation water pump—2.5L and 4.0L engines

  1. Before servicing the vehicle, refer to the precautions in the beginning of this manual.
  2. Drain the cooling system.
  3. Remove or disconnect the following: NOTESome 4.0L engines are equipped with a fan clutch that threads Directly on to the water pump shaft. This fan clutch is equipped with right-hand threads. NOTEDo not store the fan clutch assembly horizontally, silicone may leak into the bearing grease and cause contamination. NOTEOne of the water pump bolts is longer than the others. Note the location for reassembly.
    • Negative battery cable
    • Electric cooling fan connector
    • Accessory drive belt
    • Engine cooling fan and pulley
    • Water pump pulley
    • Power steering pump
    • Lower radiator hose from the water pump
    • Heater hose
    • Water pump and discard the gasket
To install:
  1. Clean the mating surfaces of all gasket material.
  2. Install or connect the following:
    • Water pump using a new gasket. Torque the bolts to 17 ft. lbs. (23 Nm).
    • Heater hose
    • Lower radiator hose
    • Water pump pulley. Torque the bolts to 20 ft. lbs. (27 Nm).
    • Power steering pump
    • Engine cooling fan and shroud. Torque the bolts to 31 inch lbs. (3 Nm).
    • Accessory drive belt
    • Electric cooling fan connector
    • Negative battery cable
  3. Fill and bleed the cooling system.
  4. Start the engine, check for leaks and repair if necessary.
3.7L Engine
  1. Before servicing the vehicle, refer to the precautions in the beginning of this manual.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Fan and clutch assembly from the pump
    • Fan shroud and fan assembly. If you’re reusing the fan clutch, keep it upright to avoid silicone fluid loss!
    • Lower hose
    • Water pump (8 bolts)
  4. Installation is the reverse of removal. Tighten the bolts, in sequence, to 40 ft. lbs. (54 Nm). 0900c1528004319e.jpgWater pump tightening sequence—3.7L

Posted on Nov 15, 2008

whispers76
  • 55 Answers

SOURCE: Changing the water pump on 2000 Jeep Grand Cherokee V6

WATER PUMP
The water pump is bolted directly to the engine timing chain case/cover.

A gasket is used as a seal between the water pump and timing chain case/cover.

If water pump is replaced because of bearing/shaft damage, or leaking shaft seal, the mechanical cooling fan assembly should also be inspected. Inspect for fatigue cracks, loose blades, or loose rivets that could have resulted from excessive vibration. Replace fan if any of these conditions are found. Also check condition of the thermal viscous fan drive. Refer to Viscous Fan Drive in this group.

The water pump can be removed without discharging the air conditioning system (if equipped)

REMOVAL
Disconnect negative battery cable from battery.
Drain cooling system. Refer to Draining Cooling System in this group.
Do not waste reusable coolant. If solution is clean, drain coolant into a clean container for reuse.

The thermal viscous fan drive is attached (threaded) to the water pump hub shaft. Remove fan/viscous fan drive assembly from water pump by turning mounting nut counterclockwise as viewed from front. Threads on viscous fan drive are RIGHT HAND. Using special tool spanner wrench 6958 with adapter pins 8346 and a suitable fan wrench loosen the fan drive Viscous Fan and Fan Drive Do not attempt to remove fan/viscous fan drive assembly from vehicle at this time.
WARNING: CONSTANT TENSION HOSE CLAMPS ARE USED ON MOST COOLING SYSTEM HOSES. WHEN REMOVING OR INSTALLING, USE ONLY TOOLS DESIGNED FOR SERVICING THIS TYPE OF CLAMP, SUCH AS SPECIAL CLAMP TOOL (NUMBER 6094) SNAP-ON CLAMP TOOL (NUMBER HPC-20) MAY BE USED FOR LARGER CLAMPS. ALWAYS WEAR SAFETY GLASSES WHEN SERVICING CONSTANT TENSION CLAMPS.

CAUTION: A number or letter is stamped into the tongue of constant tension clamps. If replacement is necessary, use only an original equipment clamp with matching number or letter.

If water pump is being replaced, do not unbolt fan blade assembly from thermal viscous fan drive.
Remove two fan shroud-to-radiator nuts Fan Shroud Mounting Hardware Do not attempt to remove fan shroud at this time.
Remove fan shroud and fan blade/viscous fan drive assembly from vehicle as a complete unit.
After removing fan blade/viscous fan drive assembly, do not place thermal viscous fan drive in horizontal position. If stored horizontally, silicone fluid in viscous fan drive could drain into its bearing assembly and contaminate lubricant.
Remove accessory drive belt as follows: The drive belt is equipped with a spring loaded automatic belt tensioner. Relax tension from belt by rotating tensioner clockwise (as viewed from front) Automatic Belt Tensioner - When all belt tension has been relaxed, remove accessory drive belt.
Remove lower radiator hose clamp and remove lower hose at water pump.
Remove seven water pump mounting bolts and one stud bolt
CAUTION: Do not pry water pump at timing chain case/cover. The machined surfaces may be damaged resulting in leaks.

Remove water pump and gasket. Discard gasket.
INSTALLATION
Clean gasket mating surfaces.
Using a new gasket, position water pump and install mounting bolts as shown. Water Pump Installation - Tighten water pump mounting bolts to 54 N·m (40 ft. lbs.) torque.
Spin water pump to be sure that pump impeller does not rub against timing chain case/cover.
Connect radiator lower hose to water pump.
Relax tension from belt tensioner Automatic Belt Tensioner - Install drive belt
CAUTION: When installing the serpentine accessory drive belt, belt must be routed correctly. If not, engine may overheat due to water pump rotating in wrong direction. Refer to Belt Routing for correct belt routing. Or, refer to the Belt Routing Label located in the engine compartment. The correct belt with correct length must be used.

Position fan shroud and fan blade/viscous fan drive assembly to vehicle as a complete unit.
Be sure the upper and lower portions of the fan shroud are firmly connected. All air must flow through the radiator.
Install two fan shroud-to-radiator nuts Fan Shroud Mounting Hardware
Be sure of at least 25 mm (1.0 inches) between tips of fan blades and fan shroud.
Install fan blade/viscous fan drive assembly to water pump shaft.
Fill cooling system. Refer to Refilling the Cooling System in this group.
Connect negative battery cable.
Start and warm the engine. Check for leaks

Posted on Jan 10, 2009

ZJLimited
  • 17970 Answers

SOURCE: where to replace coolant temp sensor for 1998 grand jeep cherokee

Check this image...

b33c4b0.png

...in the Section ZJ-Secc-8D-Ignition-Systems (page 5, fig. 10 and 11).

Good luck.



Posted on Sep 07, 2009

ZJLimited
  • 17970 Answers

SOURCE: change a headlight assembly Jeep Grand Cherokee

Just need take off the screws; for details check the graphics and ilustrations in the Jeep ZJ Grand Cherokee Service Manual

Hope helps (remember rated this) Good luck..

Posted on Jan 20, 2010

  • 30 Answers

SOURCE: fuel filter location 1998 jeep grand cherokee

The fuel filter sits on top of the fuel pump. It is the fuel fuel filter/fuel pressure regulator. You will have to drop the gas tank to access it. Hope this helps.

Best of luck

Posted on Jun 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How much does a water pump replaced cost for a 2003 Jeep Liberty?


Water Pump Replacement Cost for Jeep Grand Cherokee ...

repairpal.com > Estimator > Jeep > Grand Cherokee
This is a national average for all Jeep Grand Cherokee model years, but you can make it more accurate by adding your car info and ZIP. ... When replacing the Jeep Grand Cherokee's water pump, the drive belts and/or timing belt may need to be removed. ...Jeep Grand Cherokee water pumps ...

Water Pump Replacement Service & Cost - YourMechanic

www.yourmechanic.com > Auto Repair and Maintenance Services
How much does Water Pump Replacement cost? Get an estimate instantly. Service, parts, cost & recommendations from YourMechanic. Your definitive guide to ...

Replacing a Water Pump Cost - CostHelper.com


Dec 01, 2015 | 2003 Jeep Liberty

1 Answer

Where is the water pump on a 1995 jeep grand cherokee? Picture would help


The water pump is located rite behind the fan that turns to cool the engine . Located in the front of the engine behind the Radiator >

Aug 02, 2011 | 1995 Jeep Grand Cherokee

1 Answer

My 1998 jeep grand cherokee is running hot and leaking water, is the water pump bad?


well first i would check all the water hoses in the engine compartment for cracks and leaks then check around the radiater for leaks if you don't see any water leaking from the hoses or the radiater then try to see if you see water coming from the water pump behind the cooling fan if the water is leaking from behind the cooling fan then it is most likely your water pump

Jul 15, 2011 | 1998 Jeep Grand Cherokee

1 Answer

Where is the fuel filter of the grand cherokee 1998


1998 Jeep Grand Cherokee 4WD 5.2L MFI 8cyl the Fuel Filter is part of the fuel pressure regulator assembly which is located on the fuel pump module.The fuel pump module is located on top of the fuel tank.


Hope this helps (remember to rate this answer).

Jan 06, 2011 | 1998 Jeep Grand Cherokee

1 Answer

Fuel filter location 1998 jeep grand cherokee loredeo


The fuel filter sits on top of the fuel pump. It is the fuel fuel filter/fuel pressure regulator. You will have to drop the gas tank to access it. Hope this helps.

Best of luck

Jun 14, 2010 | 1998 Jeep Grand Cherokee

1 Answer

Where is the fuel filter on a 1998 jeep grand cherokee


For 1998 Jeep Grand Cherokee 4WD 5.2L MFI 8cyl the Fuel Filter is part of the fuel pressure regulator assembly which is located on the fuel pump module. The fuel pump module is located on top of the fuel tank.

Its possible that you are interesting in check the service manual ZJ-Secc-14-Fuel-System

Hope helps (remember rated this)..

Jun 04, 2010 | 2004 Jeep Grand Cherokee

2 Answers

Water pump replacement


haynes repair book,,it is good to have if u plan on keeping the truck,,,,tells u step by step,,

Apr 20, 2010 | 1998 Jeep Grand Cherokee

2 Answers

Small leak in a 98 jeep grand cherokee near the bottom pulley on front of engine..what is it?


If its leaking coolant, likely it is coming from the water pump above the lower pulley and running down to there. Look carefully and use a light.
If leak is oil, the pulley seal is leaking.

Feb 22, 2010 | 1998 Jeep Grand Cherokee

1 Answer

1998 jeep grans cherokee leaking water in the


Hi Vichall,

The first step is to locate the leak and identify the source.

Pull the rug back. Dry the area. This will help locate new moisture.

  • Is the water clear? Does it smell sweet?
  • Does it only leak with the engine running? After Turned off? All the time?
  • Does it only leak with the heater on? A/C on?
  • Is your coolant level down?
  • Is their a time of day it happens more? (Early morning)
Comment back with your findings. We can take it from there

Best regards
Mike


Oct 18, 2009 | 2003 Jeep Grand Cherokee

1 Answer

2005 jeep grand cherokee


The washer pump is located on the washer bottle. Must check for power at pump when applying switch if no power (12 volts) check fuse or curcuit. If it has power replace pump. Also: if pump is operational check hoses for resteictions.

Jun 13, 2009 | 2001 Jeep Grand Cherokee

Not finding what you are looking for?
1998 Jeep Grand Cherokee Logo

Related Topics:

142 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...