Question about Cars & Trucks

Open Question

How to fit cv boot on terrano

Offside outer cv boot

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 132 Answers

SOURCE: C V Boots

hi mate i dont no if this is the same case but i have found that when the boots on cv joints are perished or missing that is an indication that the roller bearings inside are worn enough to be replaced the boots are designed to keep bearings lubricated and free of dirt once there is cracks in the boot grease comes out dirt gets in and they wear out very quickly and need to be replaced replacement is easy jack up car put safety stands under bolt off bolts on simple but be shore to replace bolts with new they are usually quite stressed

Posted on Nov 09, 2008

Ad
tommyboinow
  • 324 Answers

SOURCE: replacing outer cv boot

go get a univeral boot at the store, cut the old one off with a knife, and use pliers to remove the band, and put the new ones on.

Posted on Nov 26, 2008

  • 83 Answers

SOURCE: 97 toyota celica outer cv boot replacement passenger side

have you undone the main hub bolt, if yes, there could be two different items holding the cv joint on, one is a small circlip in the joint end, or the other is just like an expanding metal ring again only small. what i had to do to change my one was take the driveshaft out (easier to see whats there) then gently (rubber hammer) hit the CV joint it should then fall off to allow you to change the CV joint. I spent over an hour trying to get the metal ring off, then after taking driveshaft off it was changed and back on in ten mins. Or you can go to a motor factors or similar and get a boot puller, my opinion hammer works better lol

Posted on Jan 25, 2009

cadman000
  • 607 Answers

SOURCE: cv boot clamp came off somehow from the outer hub assembly

athere is a snap ring within the CV joint the nedds to be spread OPEN to release CV joint from axle, Once CV is cleaned and repacked with grease rintall onto axle by again spreading apart clamp. Prior to installing CV joint slide NEW CV joint boot onto axle, Cleanly intall add'l grrease and reinstall CV boot.

Posted on Apr 04, 2009

emissionwiz
  • 76164 Answers

SOURCE: seperate outer cv from axel 99 chevy metro

to me this is a simple job, I didn't mean to sound insulting but having never done one i fixed a friends car with a bad CV joint, I found a rebuild kit with new joint ball bearings and grease boots, removing the joints is straight forward, clean the grease out of the joint to see the spring clip that holds it to the axle shaft splined end, to remove the stub end of axle from the steering knuckle undo the axle nut (u need a new one of these) and the unbolt the strut from the knuckle of course the brake caliper and the disk must also be removed, try to push the axle out and swing the knuckle out of the way, you may need to undo the tie rod as well.

Posted on May 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front outer cv boot does not fit axle. 2006 Impala 3.9.


You should be able to get a universal CV boot. Obviously, you would have to check the dimensions before buying it.

Have a look on Ebay. A supplier of CV boots should be able to sort one out for you.

impala cv boot

Mar 29, 2016 | 2006 Chevrolet Impala

1 Answer

Noise from front offside when turning the steering wheel right


this sounds like you may have a bad cv joint on the right side that will need replacing. replace the half shaft not just the outer joint.

Sep 04, 2014 | 2001 Ford Ka

1 Answer

How to split the outer cv joint to replace the rubber boot


lose the central nut of your wheel first,remove the brake caliber loose two bolts holding your suspension arm in one peace and the lower arm bolt and loose the steering arm ball joint pull the hub up and the shaft out is one peace ,loose rubber boot clean housing and look in side you have sir clip with two holes one on etch site remove it with sir clip players grease the joint fit the new boot good luck.

Sep 09, 2012 | 2004 Kia Sedona

1 Answer

Cv boot inboard boot


the reason for this is that the oem boot is not at all simple to replace, the whole cv shaft would have to be removed. the universal boot is thin and flexible to try to accomodate many variations of joints without having to remove the whole shaft. only suggestion I could make would be if your going to go thru the trouble to pull the whole shaft would be to totally replace the whole shaft. seriously its not a 30 min job, your looking at probably 3 to 4 hrs or more and thats if you have all the correct tools readily accessible. they don't come out easy, and rarely go back in easy.

Sep 09, 2012 | 2000 Ford Taurus

1 Answer

How to change outer cv boot


loosen drive shaft nut, You unbolt lower control arm pull end shaft from hub remove clamps from both endsand slide boot of or cut of and fitting is reversed proccedure

Apr 08, 2012 | 1990 Mitsubishi Sigma

2 Answers

Cv joint but the plastic thang that go around it


One would have to remove the half shaft to service the cv joint properly.

CV-Joints Overhaul Check the CV-boot for wear tccs7030.jpg

Removing the outer band from the CV-boot tccs7031.jpg

Removing the inner band from the CV-boot tccs7032.jpg

Removing the CV-boot from the joint housing tccs7033.jpg

Clean the CV-joint housing prior to removing boot tccs7034.jpg

Removing the CV-joint housing assembly tccs7035.jpg

Removing the CV-joint tccs7036.jpg

Inspecting the CV-joint housing tccs7037.jpg

Removing the CV-joint outer snapring tccs7038.jpg

Checking the CV-joint snapring for wear tccs7039.jpg

CV-joint snapring (typical) tccs7040.jpg

Removing the CV-joint assembly tccs7041.jpg

Removing the CV-joint inner snapring tccs7042.jpg

Installing the CV-joint assembly (typical) tccs7043.jpg

prev.gif next.gif

Oct 08, 2010 | 2004 Oldsmobile Alero

1 Answer

What is the easyest way to remove and replace the outer right cv boot on a nissan terrano 1995 model


Hi and welcome to FixYa. I am Kelly. First let me just say that I am passing on repeated experience and that this is NOT a solution. When a CV boot has failed it allows all kinds of foreign matter into the joint ball seats. Even if you replace the boot if you were not able to completely flush and then lubricate the joint with grease it will make noise in turns. I have had very little success with just replacing a boot as the noise factor always is present post boot replacement. Most of the time your better off with a re-manufactured Transaxle shaft. My 2 cents and will post this as a clarification so that others may still comment on "how to" replace the boot.

Kelly

Jun 30, 2010 | 1997 Nissan Pathfinder

1 Answer

Cv boot clamp came off somehow from the outer hub assembly


athere is a snap ring within the CV joint the nedds to be spread OPEN to release CV joint from axle, Once CV is cleaned and repacked with grease rintall onto axle by again spreading apart clamp. Prior to installing CV joint slide NEW CV joint boot onto axle, Cleanly intall add'l grrease and reinstall CV boot.

Apr 04, 2009 | 1996 Buick Century

1 Answer

C V Boots


hi mate i dont no if this is the same case but i have found that when the boots on cv joints are perished or missing that is an indication that the roller bearings inside are worn enough to be replaced the boots are designed to keep bearings lubricated and free of dirt once there is cracks in the boot grease comes out dirt gets in and they wear out very quickly and need to be replaced replacement is easy jack up car put safety stands under bolt off bolts on simple but be shore to replace bolts with new they are usually quite stressed

Nov 08, 2008 | 1995 Nissan Pathfinder

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...