Question about BMW Cars & Trucks

Open Question

Bmw 116 I timing chain diagram

Hi i need a timing chain diagram for this car as well as positioning of the cam shaft sensor rotors

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: 2001 Saturn SL2 cam shaft postion sensor

There are no cam shaft position sensors in this model. Check your spark plugs and the wires (boots, etc.) I had the same problem. Also a common problem in this model: if it over heats check your coolant temperature sensor. Jack up one side (drivers) of the car so less leaks out when you check it. The ones that come in the car usually crack, use the copper ones.

Posted on Nov 08, 2008

motor1258
  • 6674 Answers

SOURCE: Cam Shaft Position Sensor 1998 Saturn SL

Have a look at this link, scroll to your engine & click on picture to expand for better view.

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528017e904

Posted on Jan 23, 2009

  • 1 Answer

SOURCE: timing and balance shaft chains 4g54 mitsubishi

can an extra belt be used to bypass the air conditioner since the clutch has gone out?

Posted on Mar 31, 2009

starlet4life
  • 89 Answers

SOURCE: replacement of timing chain toyota 5k engine

Theres (if mounted correct!) two MARKS on the sprockets~these fit with the bright links on the chain~just in case anybody else needs it...

Love from Capt. Whodooooooooooo.

Posted on May 28, 2009

steve_e_uk
  • 1675 Answers

SOURCE: BMW X5 CAMSHAFT POSITION SENSOR A .SHOW DIAGRAM

hi i have a diagram if you would like it i could email it to you and there are 2 of them does it say which one it is? you can email me at
s.e.morris@hotmail.co.uk
and i will send you the diagram hope this helps

Posted on Mar 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the cam sensor in a 2002 nissan quest?


HI Chuck! The cam position sensor is inside the distributor on the quest. If the cam sensor has gone bad you need to replace the distributor assembly as it is not servicable. Before replacing the distributor, take the cap off and make sure the rotor is turning when you crank the engine. If it is not then check the timing belt as the distributor is driven by the cam shaft. If the belt is broken the cam shaft will not turn and you could get this code.The cam sensor is located under the plastic cover located under the rotor button

Nov 18, 2016 | Nissan Cars & Trucks

1 Answer

X3 bmw 04 plate eml and engine light came up and now wont start at all but turns over can you help me


possible causes are
crankshaft position sensor
cam shaft position sensor/s
ignition control module
broken timing belt/chain

Aug 19, 2016 | BMW X3 Cars & Trucks

1 Answer

What is the function of the cam sensor on the 325 E36 bmw. can the car start with a faulty camshaft sensor. If so what will the car do


as the cam shaft position sensor works in combination with the crank shaft position sensor to tell the ECM where the piston is for the correct firing and timing
it would be unreasonable to consider that the engine would function with a faulty unit
basically if the cam shaft sensor is not operational then the engine will not start

May 21, 2015 | Cars & Trucks

2 Answers

Engine rotates but wont start


run fault codes .check cam/crank shaft position sensors. Check that the cam shaft is turning (broken timing belt/chain). Check immobiliser operation

Sep 09, 2014 | 2005 Mercury Sable LS

2 Answers

Pcm?


PCM= Powertrain Control Module. It is the brains of the car, it reads the sensor in put from all sensors including the cam shaft position sensor

May 14, 2014 | 2004 Toyota 4Runner

1 Answer

No spark changed rotor,cap,coil,crankshaft position censor still nothing please help


run fault codes to check for cam/crank position sensor. check that the cam shaft is turning(broken timing belt/chain) check immobiliser operation.

Mar 11, 2014 | 1998 Jeep Cherokee

1 Answer

Timing chain marks needed for Audi A4 B9 1.8tfsi 2009 model. Engine was taken out and settings not marked. This is extremelyurgent. Please help


diagrams I have show a twin cam set up with 2 balancing shafts. The marks on the cam shaft point to (left cam shaft 11 oclock the mark on the right point to the 1 oclock position. The chain will have 3 black links-- the top black links will be at the timing marks on the shafts with the 3rd black link directly at 6 oclock facing a mark on the gear. The balancer marks both point to the 1 oclock position with black links on each and the 3rd black link will be facing a mark to the 7 oclock position on the crankahaft gear. Everything is done with the piston at TDC no 1 cylinder so get it there before you put the cam shafts in position or you will bend valves. Crank shaft gear is not keyed to the crank shaft. there are dots on the right hand balancer shaft gears and these dots will be as the 2 dots on adjacent teeth either side of a dot on the meshing gear. I suppose that is all as clear as mud but if you got this far then you will see the marks and marked links on the chains

Dec 22, 2013 | Cars & Trucks

1 Answer

Sevice code p1345 what is it truck runs good put fells like is missing at idel


p1345 is manufacture control ignition system or misfire.--. A loose CMP (cam position sensor) causing a variance in the sensor signal.

2. Excessive free play in the timing chain and gear assy.

3. Incorrectly installed distributor-1 tooth off in either advanced or ****** positions.

4. A loose rotor on the distributor shaft.

5. A loose or missing dist hold down bolt. check and or adjust distributor and shaft, could also be a bad gear on end of dist.

Aug 11, 2011 | GMC Yukon Cars & Trucks

1 Answer

Where can i find a engine diagram of a dodge 1999 3500 van


Do need you to know where the sensor is located ? If so it's located inside distributor housing, just below rotor on (3.9L-V6 5.2L-V8 5.9-V8) 8.0L-V10 cam sensor is located on the timing chain cover.

Jul 01, 2009 | 1998 Dodge Ram 3500 2WD

1 Answer

97 Chevy Astro van lugs, like it misses, B4 finally cranking on


crank shaft sen. is easy enough to change.its mounted near timing chain cover,cam sen.is somewhat harder,its in the distributor,id doubt that both are defect

Mar 09, 2009 | 1995 Chevrolet Astro

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...