Question about 1999 Mazda 626

1 Answer

With marks i use _or . at the cams

Engine 2.0l timing marks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mazda Master
  • 22,095 Answers

Look on the back of the cams to see if their are any slots on them sorry not experianced like a dealer fitter on this car so go back to basics and look ,firstly is this engine a rebuild or something or has the timing belt snapped ,if so is it a valve free engine or have got bent valves ask at dealer for this ,then TDC no1 with plug out and long thin screwdriver to locate the TDC then look at the valves engine rotates to the right so its inlet cam lobe up and to the left ,exhaust up and to the right then look for what could be a corresponding mark ,before cranking engine make sure you turn it over with a rachet and socket first 360? to ensure no valves crunching

Posted on Feb 24, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Instruction changing timing belt 1979 Alfa Romeo Spider Veloz?


With Cam Caps loosened, FIRST loosen timing chain tensioner, press it in to loosen tension, Crank using ratchet to TDC (Top Dead Center on crank pully, (to keep from damage to pistons), align Exhaust Cam Timing Mark to mark on #1 Exhaust cam cover, then take up slack between Exhaust & Intake Cams (on top between the cams), Then align the Intake Cam to mark on #1 Cam Cap, "Now" loosen the 17mm bolt to tighten timing chain, rotate engine using rachet two times, reset TDC at the crank, and look at "Cam Timing Marks on both the Exhaust, and Intake Cams. If you did all this correctly the "Timing Marks" should be lined up so TDC,Exhaust, and Intake marks are all the same.

Oct 10, 2014 | 1979 Alfa Romeo

1 Answer

1.6 LITER TIMING MARKS


g16a or b
the cam cog mark is at 12pm matching the same mark
at the back 12pm tins at rear of cam cog.
this mark is TDC #4 firing, number four.
pick 8v or 16v engine.
http://www.fixkick.com/t-belt/tbelt-index.html#Tbelt-main

documented 3 ways, by page new page, by FSM and by instruction sheet that came with all new belts (GATES)

the cam cog has 2 false marks, do no use them
use all E marks. 16v and see 8v for its false marks too.
1995 had 2 engines, 2 EFI and 2 heads. as an option.
fact. G16A or B.

Jun 29, 2014 | 1995 Suzuki Sidekick

2 Answers

Timing marks 1993


spark or cam ?????????????????
and which engine, some cars have up to 10 choices.
most are about 3 or 4.
not of this can i guess.

May 29, 2014 | 1993 Pontiac Grand Prix

2 Answers

My 2002 vw cabreo does not idle very erratic it has the 2,0L gas


1) Ignition time is incorrect. Reset the ignition timing to the specification of manufacturer.
2) Test the ignition system. see the diagram attached. God bless you.

5_15_2012_6_51_13_am.jpg5_15_2012_6_51_32_am.jpg

May 15, 2012 | Volkswagen Cars & Trucks

1 Answer

How to aline crankshaft position and camshaft position


Timing marks for a 2002 Volvo S40 2,0L engine:

tdisline_335.jpg
tdisline_336.jpg

Oct 13, 2011 | 2002 Volvo S40

1 Answer

I have found the crankshaft marks but I cannot find marks to align the to over head cams on my car, the dohc are run from 1 wheel. I am trying to re-align the timing belt as i think they have gone off.


if it's a dual overhead cam then each head has two cams and two pully's, a single overhead cam engine has one cam and one pulley on each head. if the belt has more than 60,000 miles on it you should replace it. you need to find out if the engine is an interference engine or not to determine the level of damage caused if the belt has jumped or slipped. your overhead cam timing marks are usually on the cam faces and the backing plate behind the cam or sometimes there's two marks on the cam that you align with the surface of the head behind them. the first thing you need is a diagram of the belt routing and mark positions because timing marks are very important especially on an interference engine. starting or cranking an interference engine with the timing marks misaligned can bend all your valves or even punch holes in your pistons! so proper alignment is crucial, good luck.

Jan 02, 2011 | Mazda 323 Cars & Trucks

1 Answer

Can anyone please help me with pics or detailed desription on were the timing marks should be on a toyota d4 3s-fse engine, i need to know how to place the two cams and also the timing mark on the cam...


Welcome to FIxYa.com


Need the year and model and size as in liter engine in order to look this up for you to send pic and info. Engine number does not work in Alldata, Lee


Thank you for using FixYa.com

Regards, Lee Davidian

Dec 30, 2010 | Toyota RAV4 Cars & Trucks

1 Answer

I need to know the timing marks for the timing belt on a toyota highlander 2006 , v6 , 3.3 litre. the location of the cams, is it 3 oclock, 6 oclock, 12 oclock?


the timing marks for the cams are on the rear timing cover (behind the cam sprockets). They are very hard to see, especially the rear cam. Align the cam sprocket marks with rear timing cover. Because this engine is mounted at a 60 degree angle, you must use the marks. Rear cam should feel compression while front cam is free!!

Oct 13, 2010 | Toyota Highlander Cars & Trucks

2 Answers

Cam Crankshaft timing


8 degrees before tdc

Mar 10, 2010 | 1983 Chevrolet Chevy

1 Answer

Timing belt marking


The timing marks are just above the cams at the "twelve o'clock position"

If necessary, align the timing marks.
NOTE When aligning the cam pulleys with the seal plate marks, align the left cam pulley “I” mark and the right cam pulley on the “E” mark.

WARNING When aligning the timing marks, do not turn the timing gear counterclockwise. Damage to the engine will occur.

Oct 17, 2008 | 2000 Kia Sportage

Not finding what you are looking for?
1999 Mazda 626 Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...