Question about 1999 Chrysler Sebring

1 Answer

I have a 1999 Chrystler Sebring Lxi and the gauges does not work, Any ideas on what it could be? Thanks

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Chrysler Master
  • 80,407 Answers

The instrument cluster in the car is a computer, it has many circuits that run the gauges based on information from the main computers sensors. The common problem is that the cluster electronics have failed, in order to have this repaired you must remove the cluster from the car and send it in to a factory approved instrument cluster repair center. Call your local dealer for a address and contact info.

Posted on Feb 24, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
ewashmidas
  • 362 Answers

SOURCE: 1999 chrysler sebring lxi service engine light on

Your vehicle’s computer system has self-testing capability. When the computer senses that there is a problem with one of the components or sensors it stores the correspondent trouble code(s) in its memory and lights up the "Check Engine" or "Service Engine Soon" light to tell you that there is a problem and you need to diagnosed and repaired it. If the light starts flashing, this is evidence of a serious problem and the vehicle should be taken to a repair facility or you need to repair it immediately.

Posted on Feb 14, 2009

c17hydro
  • 2984 Answers

SOURCE: how can i replace the crankshaft position sensor

Fig. 2: Location of the crankshaft position sensor on 2.4L engines

fabab4c.jpg

Posted on Jun 25, 2009

co7196
  • 3433 Answers

SOURCE: i need the firing order on a 1999 chrysler sebring

153624 on a six cylinder. This should be in cast on the intake manifold. To locate what tower to use on the cap, do this. pull the #1 plug. Bring it to tdc on the compression stroke. Now chk out where the rotor is pointing and that's the tower for #1. Good Luck -Ned-

Posted on Sep 16, 2009

Molson02536
  • 3854 Answers

SOURCE: i have a 2001 chrystler sebring coupe lxi 3.0

Bank 1 is the exhaust manifold at the firewall, sensor 2 is the O2 sensor after the catalytic converter.

Posted on Nov 17, 2009

kel1guy2002
  • 3740 Answers

SOURCE: how often do i replace the timing chain 1999

The belt is supposed to last for 105,000 miles. These sebring cars are notorious for breaking timing belts well before then. If your car has over 80,000 on it I would schedule a timing belt change in the near future. Don't be surprized if you have to also change the water pump.

Kelly

Posted on Feb 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I stop my turn signal from blinking in my 1999 Chrystler Sebring XL?


The switch is broken if it keeps blinking. Replace the switch

Jun 07, 2015 | 1999 Chrysler Sebring

1 Answer

Where are the O2 sensors located99 chrysler sebring lxi?


They should in the exhaust pipes just before the catalytic converter

Feb 16, 2015 | 1999 Chrysler Sebring LXi

1 Answer

Remove tranny from a 1999 sebring 2.5 lxi does the engine come with??


Yes the motor comes out the top..transmission out the bottom. sounds like you need help.maybe buy a Break down manual for your year vehical it shows how the whole thing comes apart
.good luck

Jan 26, 2015 | 1999 Chrysler Sebring LXi

1 Answer

I need a diagram to put on a serpintine belt for a Chrystler Seebring LXI 2 door Coupe


There should be a diagram somewhere under hood. If not, check shop manual (might be able to just look at one a parts store if you feel it is too expensive to buy).

Mar 27, 2014 | 2002 Chrysler Sebring

2 Answers

Location of cam pos sensor on 2000 chrystler sebring lxi? thank you and how much should it cost?


The camshaft position sensor for your vehicle is located in the distributor housing. It is serviced only as a complete distributor assembly, individual parts are not available.

The manufacturer (dealer) suggested retail price (MSRP) for the distributor assembly (Part Number MD345492) is $1100.00 (US).
The standard flat-rate labor time to replace it is 0.8 hours.
(you will have to figure the labor cost depending on labor rates in your area)

AutoZone has remanufactured distributors listed for your vehicle at a cost of around $275.00.

CARDONE part number 84-49600 is a NEW distributor and lists for $425.00

Aug 19, 2011 | 2000 Chrysler Sebring

1 Answer

How can i replace the crankshaft position sensor on a 1999 sebring lxi


Fig. 2: Location of the crankshaft position sensor on 2.4L engines

fabab4c.jpg

Jun 25, 2009 | 1999 Chrysler Sebring

Not finding what you are looking for?
1999 Chrysler Sebring Logo

248 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

80407 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...