Question about 1994 Honda Civic

1 Answer

How can i clean the inside of my honda head? - 1994 Honda Civic

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 377 Answers

Your local auto store will have a product called " engine flush ", you add it to the engine oil drive the car for a few miles and then change the oil and filter, the flush will have cleaned/removed all the sludge etc during the drive and all should be good,

Posted on Feb 24, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What lbs do I tighten the head bolts to on my 1990 Honda prelude SI 2.1L DOHC and in what order do I tighten them?


Go inside the local Autozone and ask for the cylinder head torque specs. They will look it up and print it out for you. It will contain the torque specifications as well as the sequences. Happy torquing.

Mar 01, 2015 | 1990 Honda Prelude

1 Answer

How to replace a thermostat on a 1996 honda accord dx?


It has been some time since I looked at a Honda, but it is usually quite easy to identify the thermostat housing. It is a dome shaped fitting where the top radiator hose is connected to the cylinder head.

This fitting is bolted down with either two or more likely three bolts.

Undo the three bolts, then carefully separate the thermo housing from the cylinder head using quite a bit of force.

Carefully, because it is made of cast aluminium, but it is also stuck down with gasket sealer and lots of heat from the engine - it normally takes a hard smack on the flange or a flat object such as a screwdriver wedged between the flange and the head to loosen it.

Once open you will find the thermostat inside. Replace it with a new one and don\'t forget the rubber "O" ring, and if it was sealed with silicon sealer, clean all surfaces and add fresh sealant.



Good luck.

Oct 06, 2014 | Cars & Trucks

1 Answer

Why do I have oil in my 1997 honda civic coolant reservoir tank.


A few things could have happen,
1 you overheated and blew the head gasket and now the oil in mixing with the anti-freeze,
OR due to high Mileage the head gasket has just failed and is leaking into the anti-freeze journals inside the engine.,

Did you check the oil to make sure it's not a white'ish sludge on the inside of the cap, you might be mixing both back and forth..

Sep 18, 2014 | 1997 Honda Accord

1 Answer

Honda Headlights only work in high beam


have you check to see if the bulbs are burned out many never knew the first one was out till there both burned out there are fuses in the under hood fuse box

Aug 15, 2012 | 1998 Honda Civic

1 Answer

Need to replace starter and cannot get to bolts to undo - what can i do to get this done myself


Space to turn the bolts is sometimes restricted - requiring a special tool to get it to mount properly.

Clean bolt heads with WD40 or penetrating oil to get at the thread inside. Leave it for a few hours then try again.

If the engine can be started - let the engine housing heat up for a bit and try again.



Jun 26, 2011 | 2003 Honda CR-V

1 Answer

How to replace engine air filter in 2001 honda odyssey


The air cleaner element is inside the air cleaner housing on the driver's side of the engine compartment.
To replace it:
1. Remove the two pins holding the air intake cover by pulling the head on each pin. Remove the air intake cover.
2. Loosen the four bolts by using a Phillips-head screwdriver.
3. Disconnect the clip from the bolt on the air cleaner housing, then remove the air cleaner housing cover.
4. Remove the old air cleaner element.
5. Carefully clean the inside of the air cleaner housing with a damp rag
(The coolant lines inside the air cleaner housing may be warm. Do not open the hot air valve when cleaning the inside of the air cleaner housing)
6. Place the new air cleaner element in the air cleaner housing.
7. Reinstall the air cleaner housing cover. Reinstall the clip on the bolt; make sure the clip is under the washer. Tighten the four bolts.
8. Reinstall the air intake cover. Reinstall the two pins and secure them by pushing on the heads until they lock.

Hope this helps you through the process.

Nov 23, 2009 | 2001 Honda Odyssey

1 Answer

Just replaced a head gasket on a 98 honda crv. It still overheats but there is no oil in the water so the head leak is fixed. What could be wrong??


When this happens with any car you should have your radiator cleaned, replace the water pump and resurface the head, dont forget to replace the thermostat too.

Jul 19, 2009 | 1998 Honda CR-V

1 Answer

Install of inside door handle for honda accord


philips head screw driver and a flat tip to take plastic rod holder... very easy...pry rod off old and replace w/ new... unplug powerwindow switch if applicable

Oct 21, 2008 | 1992 Honda Accord

1 Answer

Clean the inside of the head lamp lens and replace bulb


If the inside of the headlight assembly is getting dirty, it means that you have a crack or opening in it some where.

Replacing the bulb is just a matter of taking the bulb socket out of the housing (usually a 1/4 turn, and remove). Make sure not to touch the new bulb with your fingers. If you do, clean it off with alcohol before putting it back in. The oil from your fingers can cause the bulb to fail prematurely.

You might want to take it off the car, clean it in the sink, and dry it out, and then look for any damage in the housing. Do not put it back into the car until after it has dried completely.
Depending on the damage, you might be able to repair it, otherwise, you might be looking at replacement.
3rd option would be leave it as it is, and clean as needed.

Aug 01, 2008 | Honda Accord Cars & Trucks

Not finding what you are looking for?
1994 Honda Civic Logo

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...