Question about 2004 Ford F150
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: 2000 Ford Ranger
TEST B: BATTERY VOLTAGE OUT OF RANGE - DTC B1676
1. Check if vehicle has been jump started within past 2 weeks. If vehicle has been jump started, ABS is
okay. If vehicle has not been jump started, go to next step.
2. Using DVOM, measure voltage between positive and negative battery terminals. If voltage is 9-19 volts,
go to next step. If voltage is not 9-19 volts, diagnose charging system. See appropriate GENERATORS
article in STARTING & CHARGING SYSTEMS.
3. Turn ignition off. Disconnect 25-pin ABS control module. Install EEC-IV 60-pin Breakout Box (014-
00322). Turn ignition on. Measure voltage between breakout box terminal No. 20 and ground. If voltage
is more than 10 volts, go to next step. If voltage is less than 10 volts, repair Light Blue/Pink wire between
ABS control module and instrument panel fuse panel.
4. Turn ignition off. Measure voltage between breakout box terminal No. 25 and ground. If voltage is
greater than 10 volts, go to next step. If voltage is less than 10 volts, repair Red wire between ABS
control module and power distribution box/engine compartment fuse box.
5. Measure voltage between breakout box terminal No. 9 and ground. If voltage is greater than 10 volts, go
to next step. If voltage is less than 10 volts, repair Yellow/Light Green wire between ABS control module
and power distribution box/engine compartment fuse box.
6. Measure resistance between breakout box terminal No. 8 and ground. Also, measure resistance between
breakout box terminal No. 24 and ground. If both resistance measurements are less than 5 ohms, replace
ABS control module and repeat self-test. If either resistance measurement is greater than 5 ohms, repair
suspect Black wire between ABS control module and ground distribution.
NOTE: DTC B1676 will set if vehicle has been jump started.
2000 Ford Ranger
2000-01 BRAKES Anti-Lock - 4WAL - Explorer, Ranger & Mountaineer
Posted on Jun 11, 2008
go to www.motorcraftservice.com then click on the owner guide and put in your truck information
then choose the 1st owner manual printing and should be between page # 184 to 200.
Good luck and I hope this will awnser your question.
Posted on Nov 08, 2008
I am not sure if this right and there should be diagram on the back of cover.
1 5A Power Mirror Switch
2 10A Daytime Running Lights (DRL),
Back-up Lamps, Transmission,
Passenger Air Bag Deactivation
Switch, Blower Motor Relay
3 7.5A Right Stop/Turn Trailer Tow
4 — Not Used
5 15A 4x4 Control Module
6 — Not Used
7 7.5A Left Stop/Turn Trailer Tow
8 — Not Used
9 7.5A Brake Pedal Position Switch
10 7.5A Speed Control Servo/Amplifier
Assembly, Generic Electronic
Module (GEM), Shift Lock
Actuator, Turn Signals
11 7.5A Instrument Cluster, 4x4, Main
Light Switch, Truck Central
Security Module (TCSM)
12 — Not Used
13 20A Brake Pedal Position Switch
14 10A or Not Used 10A: If equipped with Anti-Lock
Brake System (ABS) Control
15 — Not Used
16 30A Windshield Wiper Motor, Wiper
Hi-Lo Relay, Wiper Run/Park
17 20A Cigar Lighter, Data Link
18 — Not Used
19 25A PCM Power Diode, Ignition, PATS
20 7.5A Generic Electronic Module
21 15A Flasher (Hazard)
22 20A Auxiliary Power Socket
23 — Not Used
24 7.5A Clutch Pedal Position (CPP)
switch, Starter Interrupt Relay
25 — Not Used
26 10A Battery Saver Relay, Auxillary
Relay Box, Restraint Central
Module (RCM), Generic Electroic
Module (GEM), Instrument
27 — Not Used
28 7.5A Generic Electronic Module
29 20A Radio
30 — Not Used
31 — Not Used
32 — Not Used
33 15A Headlamps, Daytime Running
Lamps (DRL) Module, Instrument
34 — Not Used
35 15A or Not Used 15A: Horn Relay if Not Equipped
with Truck Central Security
36 — Not Used
Posted on Jun 02, 2009
SOURCE: 2000 ranger fuse diagram
Fuel Pump relay switch is in the main box usually located on the drivers side Fender in a black box.
According to the owner's manual in the power distribution box in the engine
compartment (Ford recommends disconnecting your battery)
Relay # 5 is the fuel pump relay , and also in the PD BOX is a 20 amp mini-fuse
for the fuel pump relay + RAP module in location # 9
( P.S. - don't forget your fuel pump inertia switch , in the right front passenger area ,
by the right front kick panel )Sometimes this gets kicked by passenger or if the car is bummed hard it could set this item to shut down fuel system. Best of Luck
Posted on Aug 28, 2009
Testimonial: "I was skeptical, but the answer fit & worked. Thanks!"
Look on the top of the engine. The EGR valve is usually shaped like a UFO with a vacuum line going from the top of it to the EGR valve sensor. That's how it is with my 4.0L SOHC. Hope this helps. God bless
Posted on Oct 23, 2009
Tips for a great answer:
Jan 03, 2014 | 2003 Ford Ranger Regular Cab
Mar 30, 2010 | 2000 Ford Ranger SuperCab
Feb 09, 2010 | 2000 Ford Ranger SuperCab
Aug 28, 2009 | 2000 Ford Ranger SuperCab
May 06, 2009 | 2000 Ford Ranger SuperCab
Mar 22, 2009 | 2000 Ford Ranger SuperCab
Jan 04, 2009 | 2000 Ford Ranger SuperCab
Jun 11, 2008 | 2000 Ford Ranger SuperCab
50 people viewed this question
Usually answered in minutes!