Question about 1991 Honda Prelude

Open Question

1991 honda prelude engine torque specs

Engine torque specs

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
jamesmac
  • 71 Answers

SOURCE: Replacing head gasket on 1995 honda civic, require torque specs and secquence

7.3 ft.lbs Go from middle, to back right, to back left, to front right, to front left. if your standing in fron of your header.  11 or over usually shears the bolt.(if you have stock bolts)
Make sure you dap some rtv on the sharper 4 corners of the gasket where the cam seals are.

James Mac

Posted on Sep 13, 2008

Ad
  • 3 Answers

SOURCE: honda prelude si 1991

I had the sme problem with my 1992 prelude si. The problem with mine was that the intake manifold gasket was leaking horribly. The idle would go up and down just setting there, but when I held the brake long enough it stopped. An easy way to see if it is the gasket is get WD40 or Brakleen or soemthing like that, and spary it where the intake manifols bolts to the block. If you hear a change in the idle speed (faster or slower) just change out the gasket.

Posted on Mar 31, 2009

  • 3 Answers

SOURCE: transmission dipstick

Look on ths side the transmission is located on, and look for a yellow handled dipstick. It should be on the front of the transmission somewhere

Posted on Mar 31, 2009

  • 31 Answers

SOURCE: 1991 honda prelude speedometer not working,what is

your cable is either broken or can loose on your trans axle or behind your instrument cluster. Check those first. cost ????? not sure

Posted on Sep 21, 2009

SOURCE: Torque specs for 96 Honda Accord 2.2L

the main bearings bolts is to 1st step 30Nm or 22lbs ft and the last step is 75Nm or 54lbs ft in this tighten secuence. 9 3 1 5 7 on the top bolts and........ ........ ........ ... 8 6 2 4 10 botton bolts and the connecting rod 45Nm or 34 lbs ft i hope be help you

Posted on Nov 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What lbs do I tighten the head bolts to on my 1990 Honda prelude SI 2.1L DOHC and in what order do I tighten them?


Go inside the local Autozone and ask for the cylinder head torque specs. They will look it up and print it out for you. It will contain the torque specifications as well as the sequences. Happy torquing.

Mar 01, 2015 | 1990 Honda Prelude

1 Answer

What are the torque specs for the cam journals on a 1991 Honda 2.2


all here:
http://honda-tech.com/honda-crx-ef-civic-1988-1991-3/%5Bfaq%5D-d-series-torque-specs-everyone-1169414/

Feb 21, 2015 | 1991 Honda Accord

2 Answers

Head torque specs for 92 honda accord with f22a1


Thanks for using FixYa.

To install:
  1. Install a new head gasket on the engine, making certain it is positioned correctly. The cylinder head dowel pins and the oil jet must be in place. Refer to the illustrations if necessary.
  2. Install the head. Lower it straight down onto the block, aligning it correctly.
  3. Apply clean engine oil to the bolt threads and the contact face of the bolt head. Install the head bolts finger-tight.
  4. On all models except 1988-89 DOHC Prelude and 1992-95 Preludes with 2.3L and VTEC engines, tighten the head bolts following sequence A. On 1988-89 DOHC Preludes, use sequence B. Use sequence C on 1992-95 Preludes with 2.3L and VTEC engines.
    1. On 1984-89 Accords and 1984-91 Preludes, tighten the bolts in two passes. The first pass should bring the bolts to about 22 ft. lbs. (30 Nm). On the second pass, tighten the bolts to their final torque of 49 ft. lbs. (68 Nm).
    2. On 1990-93 Accords, tighten the bolts to 29 ft. lbs. (40 Nm) on the first pass, 51 ft. lbs. (70 Nm) on the second pass, then tighten the bolts to their final torque of 78 ft. lbs. (108 Nm).
    3. On 1994-95 Accords and 1992-95 Preludes, the bolts are also tightened in three passes. Tighten the bolts to 29 ft. lbs. (40 Nm) on the first pass, 51 ft. lbs. (70 Nm) on the second pass, then tighten the bolts to their final torque of 72 ft. lbs. (100 Nm).

      0900c152800b80b4.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Fig. 9: Cylinder head bolt torque sequence A

      jturcotte_2331.gif

      Fig. Fig. 10: Cylinder head bolt torque sequence B


      0900c152800b80b6.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Fig. 11: Cylinder head bolt torque sequence C


  5. If applicable, assemble the intake and exhaust manifolds to the head. Use new gaskets.
  6. If applicable, install the cam, rockers and camshaft holders.
  7. If equipped, install the EGR crossover and air suction pipes.
  8. Connect the exhaust pipe to the manifold using new nuts.
  9. Install the timing belt.
  10. Install the valve cover.
  11. Install the cylinder sensor (if equipped) and the distributor.
  12. If applicable, install the alternator.
  13. Install the power steering pump, then connect the inlet hose to the pump.
  14. Install the accessory drive belts. Adjust the belt tensions.
  15. Install the heater hoses.
  16. Install the cruise control actuator if it was removed.
  17. Connect the spark plug wires. Connect all the wire harnesses and vacuum hoses to the cylinder head, intake manifold and throttle body/carburetor.
  18. Connect the throttle control cable and/or accelerator cable at the throttle body.
  19. Connect the fuel lines.
  20. Install the brake booster, PCV and charcoal canister vacuum hoses.
  21. Install the air cleaner and intake duct.
  22. Refill the engine coolant. It is recommended that the engine oil be changed whenever a cylinder head is removed.
  23. Connect the negative battery cable.
  24. Start the engine, allowing it to idle. Bleed the cooling system. Check the work area carefully for any signs of fluid leakage or any indication of the timing belt rubbing or slapping the covers.

Sep 25, 2011 | Honda Accord Cars & Trucks

1 Answer

I am looking for torque specs on a 91 honda prelude 2.1l.I need specs and sequence for the main bearing caps and rod bearings


the specs for the 1991 prelude with a 2.1 engine are, the connecting rod caps are 34 ftlbs and the main bearing cap are 49 ft lbs, hope this helps,

Sep 10, 2010 | Honda Prelude Cars & Trucks

1 Answer

Cyl head bolt torque 1990 honda prelude dohc


mcdevito75 here, your local parts store can give you the specs.

Jun 17, 2010 | 1990 Honda Prelude

1 Answer

Torque specs for head bolts, 1990 Honda prelude si


49lbs I believe but it should tell you in the manual or goto a Kragen store and just flip thru a Haydem or Chilton repair book real quick.

May 03, 2010 | 1990 Honda Prelude

1 Answer

I need the torque specs on a 92 prelude 2.3


Oil the gasket first with engine oil - let it soak for a minute or two (its in the manual!) First stage 40nm - second stage 70nm - third stage 100nm - Tightening sequence - looking from top of engine with the flywheel on the left, top set of bolts from top left to top right bolts 1,2,3,4,5--------- Bottom set of bolts bottom left to bottom right 6,7,8,9,10-------- tightening sequence is - 8,3,7,4,9,2,10,1,6,5 -

Jan 01, 2010 | 1990 Honda Prelude

1 Answer

Having problems setting the timing marks on the belt for a 1991 honda prelude


I don't know if you know this but Honda engines turn backwards. Looking at the front of the motor Honda engines turn counter clockwise. All others turn clockwise.

May 01, 2009 | 1983 Honda Prelude

1 Answer

Need torque spec. for 91 honda crx head bolts


47 FT LBS TORQUE.is for the 1.5 and 1.6 engines 2.2 is 78 ft lbs and the 2.0 -2.1 is 49 ft lbs. the crx engine is 47 ft lbs

Apr 03, 2009 | 1991 Honda CRX

Not finding what you are looking for?
1991 Honda Prelude Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...