Question about GMC Envoy

Open Question

P0140 secondary air injection system - Envoy GMC Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 373 Answers

SOURCE: secondry air injection system malfunction

Hi. I'm reading your request.

Your S10 . has a small fuse box Next to the battery.
1 - air solenoid 10 amp.
1 - air fuse 30 amp.
1 - Mini relay (air relay)

On under hood main fuse block you have.
1 - fuse Engine E 10 amp.

Posted on Jul 12, 2008

Ad
Molson02536
  • 3854 Answers

SOURCE: secondary air injection system

This is a pump that sits underneath your front bumper on the passenger side. It is about the size of a baseball and has two hoses going into it. I would suggest you replace it yourself as it would cost you about $360.00 if you were to go through the dealer.

Water intrusion is what will typically kill these electric pumps. There is a Technical service bulletin (#04-06-04-015) Regarding this problem, according to the tsb, you will need a new pump and there is a hose assy. #12590627) that has you reroute the pump from future water intrusion or it is guaranteed to fail again.

Although I have had water in the pump I did not see any indication of the inlet hose as the cause. It was suggested that the one way metal check valves ($15.00) that mount to the rt & lt exhaust manifold are worn and allow water from the exhaust to get sucked back into the pump. I first replaced the pump and within a week of dry weather driving the light came back on. I checked the pump and it was again full of water. I just replaced the valves which had deteriorated on the inside. So hopefully this will eliminate the problem. Note - The valves are impossible to remove without removing the 1/2 tubes (held on with 2 nuts) they are attached to the manifold with. The valve threads seize to the tube thread and had to be clamped in a vise to remove - I actually had to hacksaw the valve section to get it off the pipe. Careful as not to damage the threads.

Good luck and try autopartsdirect2you for a new pump and it has life time warranty.

TSB #04-06-04-015 - (Mar 22, 2004)

Condition
Some owners may comment on the check engine light being illuminated. Upon investigation, the technician may find a DTC P0410 indicating that there is a concern in the secondary air injection system.

Cause
Water may have collected in the AIR pump or the vent solenoid and frozen or corroded the pump.

Correction
Replace the AIR pump and install a new inlet hose and solenoid tube assembly using the following procedure:

Prep vehicle.
Raise vehicle on hoist.
Remove shield covering AIR pump.
Remove hose and vacuum lines from pump and solenoid.
Remove AIR pump inlet hose. Do not re-use.
Disconnect electrical connectors from pump and solenoid.
Remove pump mounting bolts and pump.
Transfer isolators from the old pump to the new pump.
Install new AIR pump and bolts to vehicle.

Tighten
Tighten the bolts to 17N·m (12.5 lb ft)

Route new hose assembly up between engine and fender. It should come up near the area between the battery and the coolant bottle.
Connect new inlet hose to pump inlet.
Connect old outlet hose to pump outlet.
Connect electrical connector to pump.
Connect electrical connector for solenoid to connector on the new hose assembly.
Connect the hose with the white nipple to the vacuum source hose.
Connect the remaining hose to the shut off valve.
Install shield covering AIR pump.
Lower vehicle.
Remove coolant reservoir nut nearest the battery.
Route new hose assembly between the battery and the coolant reservoir with the solenoid on top.
Install the solenoid bracket onto the coolant reservoir stud and reinstall the nut back into the vehicle.
Use a wire tie to keep the new hose assembly away from the engine. On four cylinder engines, tie to the AIR outlet hose. On six cylinder engines, tie to an available hole in the radiator fan shroud.

12590627 Hose Assembly - Secondary Air Injection

12568324 Pump, Secondary Air Injection for 2001 L35 + 2000-2003 L43/LN2

12560095 Pump, Secondary Air Injection for 1999-2000 L35

Hope that helps

Posted on Mar 06, 2010

  • 1 Answer

SOURCE: 1. Trouble Code #00410 "States

I have a 2000 2.2L Sonoma that I had to replace the motor in with a 99 engine and when I did the exhaust manifold was different and I could not hook up my air pump and I now have a service engine light on all the time but it runs just fine and I even think it improved my gas mileage. You might check your air pump connections or sensor. The air pump is on the front of the engine below the ac unit. I TOO have a Hanes book but also a Chilton book because 1 covers some things the other does not

Posted on Sep 11, 2010

  • 496 Answers

SOURCE: The code P0140 secondary air

P0140=O2 sensor circuit--no activity detected (bank 1 sensor 2)

Posted on Feb 04, 2011

Terry Tate
  • 23 Answers

SOURCE: OBDII says secondary air injection

This is a pump that pushes air into the exhaust manifold of your car. Typically when this code occurs the one way valve which prevents water from going back into pump has failed. You can usually just replace the valve to fix this problem.

Posted on Mar 15, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2008 Trailblazer has OBD-II code P2430. How do I replace the secondary air injection pump?


This code doesn't mean to replace the air pump ,
DTC P2430 : Secondary Air Injection (AIR) System Pressure Sensor Circuit
Circuit/System Description
The secondary air injection (AIR) system aids in the reduction of hydrocarbon emissions during a cold start. The system forces fresh filtered air into the exhaust stream in order to accelerate the catalyst operation. An electric air pump, the secondary AIR injection pump, provides filtered air on demand to the AIR control solenoid valve/pressure sensor assembly. The AIR control solenoid valve/pressure sensor assembly controls the flow of air from the AIR pump to the exhaust manifold. The AIR solenoid relay supplies the current needed to operate the AIR control solenoid valve/pressure sensor assembly. A pressure sensor is used to monitor the air flow from the AIR pump. The engine control module (ECM) supplies the internal pressure sensor with a 5-volt reference, an electrical ground, and a signal circuit.
This is a pressure sensor problem . What this video on testing !
Chevrolet Malibu P2432 Secondary Air Injection System

May 11, 2017 | Cars & Trucks

1 Answer

Diagnosis read fault p336


p0140 - 02 sensor circuit no activity detected, (bank 2 sensor 1)
P0170 - fuel trim malfunction (bank 1) MM6LP - fuel injection fault
P0336 - Crankshaft Position Sensor A Circuit range/performance SID801/4 - Engine speed signal coherence.
P0352 - Ignition coil B Primary/secondary circuit malfunction MM6LP - 2/3 ignition coil control. Open circuit, short circuit to positive, short circuit to earth. ME746 - NO.1 Ignition coil control function. Short circuit to earth. ME746 - NO.2 ign. coil control function. Short circuit to earth.
P0414 - Secondary Air Inj. system switching valve A circuit shorted. MM6LP - Air pump relay control failure.

Mar 21, 2014 | 2008 Peugeot 307cc 1.6

1 Answer

Mercedes Benz R 350, 2008 error P0411


Error Code: P0411
Description:
Secondary Air Injection (AIR) System - Incorrect Flow Detected
Indication:
Malfunction Indicator Lamp (MIL) ON.
Reasons:
Secondary air injection (AIR) pump.
Secondary air injection (AIR) valve.
Secondary air injection (AIR) hose(s).

Feb 21, 2014 | 2007 Mercedes-Benz C230 Sedan

1 Answer

I replaced my secondary air check valve on my 2001 chevy tahoe but code 1416 still comes up. what else can i check


here is what i found on p1416.



P1416 Chevrolet
P1416 Chevrolet - Secondary Air Injection System Bank 2
Possible causes
- Faulty Secondary Air Injection (AIR) pump
- Secondary Air Injection check valve bank 2
- Secondary Air Injection (AIR) pump electrical circuit fault
- Blocked Secondary Air Injection (AIR) system

When is the code detected?

The P1416 code is set when no O2 sensor voltage change is detected by the Engine Control Module (ECM).


Possible symptoms
- Engine Light ON (or Service Engine Soon Warning Light)


P1416 Chevrolet Description
An Secondary Air Injection (AIR) pump is used on this vehicle to lower tail pipe emissions on start-up. The PCM supplies a ground to the AIR pump relay, which energizes the AIR pump. The Powertrain Control Module (PCM) monitors the HO2S voltages to diagnose the AIR system. During the AIR test the PCM activates the AIR pump during closed loop operation. When the AIR is activated, the PCM monitors the HO2S voltages and short term fuel trim values for both banks of the engine. If the AIR system is operating properly, the HO2S voltages should go low and the short term fuel trim should go high.

Jan 23, 2014 | 2001 Chevrolet Tahoe

1 Answer

Code po 491 and po 492


P0491 Secondary Air Injection System (Bank 1)
P0492 Secondary Air Injection System (Bank 2)
Good luck for you!
OBD2 code reader

Jun 25, 2013 | 2001 BMW 330

1 Answer

How to clean secondary air injection incorrect upstream flow detected Code PO411


The valve may need to be replaced. Only air flows thru the components.

Jul 03, 2012 | 2008 Chevrolet TrailBlazer LT

1 Answer

I have a 2000 vw passat GLX V6 5 Speed with the error codes p1411 -p1423 how do i fix it


P1411 = Secondary air injection system, bank 2 - insufficient flow detected.
Probable cause: Intake leak, hose(s) blocked / leaking, secondary air system valve / solenoid.

P1423 = Secondary air injection system, bank 1 - insufficient flow detected.
Probable cause: Intake leak, hose(s) blocked / leaking, secondary air system valve / solenoid.


Mar 13, 2011 | 2000 Volkswagen Passat 4Motion

2 Answers

Obd code of p0411 on a 1999 ford mustang 3.8 v-6 what do I check to correct


That's s failure of the secondary air pump. It'll have to be changed. It's an emissions component meant to help with cold start emissions. It won't cause engine running trouble but at inspection time you'll fail for smog. Change it before then and you'll be fine.

May 16, 2010 | 1999 Ford Mustang Cobra

1 Answer

I have a code P0491 coming up on my 2004 Dodge Stratis, this is a secondary fuel injection system and don't know wear to start to correct this.


P0491 Secondary Air Injection System (Bank 1)
This code is not fuel injection but air injection, replace the secondary air injection pump.

Apr 20, 2009 | 2004 Dodge Stratus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...