Question about 2002 Mitsubishi Eclipse

1 Answer

Ran my mitsubishi eclipse 2002 2 trouble codes p0340 camshafft position sensor circuit malfunction and p0335 crankshaft position sensor a circuit malfunction what is this and how do i go about fixing it if possible what might it cost me to get it fixed either myself or let someone else fix it

Posted by on

  • mbolton10 Feb 23, 2012

    if it makes a difference its a 2003 mitsubishi eclipse 2door 4 cylinder

  • mbolton10 Feb 23, 2012

    my bad

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have a 2000 eclipse and got a trouble shooting code p0340 for a camshaft position sensor. but my car dont have one?

Posted on Jun 04, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Big Poppa Ma
  • 302 Answers

SOURCE: 2002 Eclipse

its by your intake manifold on the bottom of the engine block. there is a heat shield covering it which will need to be removed to get to it

Posted on Dec 06, 2008

DSMprostyle
  • 37 Answers

SOURCE: crankshaft position sensor location

Hello. One way to check if it is working is when you try to start the car does the needle move on you tac? If not then your crank sensor is more then likely the problem. It is located on the backside of the engine under the intake manifold. If is in about the center of the block. There will be a 10mm bolt holding the sensor in. If you decide to change it yourself (not to terrible of a job) unplug the sensor, remove the bolt and spin it back and forth slightly while pulling it out. It may be stoburn and you might have to work at it for a little bit (not a done of room) but it will come. When it's out the sensor will be shaped kind of like an L. I have changed a few of these over time and they can be a little stoburn. To install just reverse the process.

Posted on Mar 26, 2009

dsacco86
  • 1077 Answers

SOURCE: Mitsubishi Galant 2002 will not start

Glad I can help. :)

Posted on Apr 19, 2009

GARYca
  • 672 Answers

SOURCE: Change a crankshaft position sensor on a 2000 eclipse

Is this a V6 or 4cyl???>>>(V6) This requires removing the Harmonic balancer (crankshaft pulley). Remove (R) front wheel, remove engine splash Guard, Remove crank pulley, remove lower timing belt cover. The Crank sensor is located behind the crank shaft pulley!! I highly recommend having this done by a certified tech, requires special tools. Hopefully this helps!!

Posted on Mar 11, 2010

  • 462 Answers

SOURCE: 2002 Mitsubishi Galant 2.4 with repeating error codes P0335,P0340

Check your timing marks , you may have jump the tooth on a timing belt.

Posted on May 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am workimg on my 2000 nissan quest. it cranks and turns over but will not start. it is throwing codes P0340 twice and P0325. we replaced the distributor cap and rotor and still nothing. probably goi


P0325 Knock Sensor 1 Circuit (Bank 1 or Single Sensor) -Circuit Malfunction
P0326 Knock Sensor 1 Circuit Range/Performance (Bank 1 or Single Sensor)
P0327 Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)
P0328 Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)
P0329 Knock Sensor 1 Circuit Input Intermittent (Bank 1 or Single Sensor)
P0330 Knock Sensor 2 Circuit (Bank 2) -Circuit Malfunction
P0331 Knock Sensor 2 Circuit Range/Performance (Bank 2)
P0332 Knock Sensor 2 Circuit Low Input (Bank 2)
P0333 Knock Sensor 2 Circuit High Input (Bank 2)
P0334 Knock Sensor 2 Circuit Input Intermittent (Bank 2)
P0335 Crankshaft Position Sensor -Circuit Malfunction
P0336 Crankshaft Position Sensor -Range/Performance
P0337 Crankshaft Position Sensor -Low Input
P0338 Crankshaft Position Sensor -High Input
P0339 Crankshaft Position Sensor -Intermittent
P0340 Camshaft Position Sensor A Circuit (Bank 1 or Single Sensor) -Circuit Malfunction
sorry would a play with this to know for sure ,check the wiring plugs onto the sensors to make sure their not full of oil or corroded

Aug 07, 2014 | 2000 Nissan Quest

1 Answer

Engine management light on trouble code P0335


P0335 - Crankshaft Position Sensor 'A' Circuit Malfunction

Possible causes- Faulty crankshaft position sensor (most common)
- Crankshaft position sensor harness is open or shorted
- Crankshaft position sensor circuit poor electrical connection
- Signal plate may be damage
- Starter motor may be faulty
- Starting system circuit
- Dead or weak battery causing slow engine crank over.

Oct 25, 2012 | 2005 Fiat Punto

1 Answer

2001 Oldsmobile Aurora Codes P0302, P0335, P385, P0386


p0302 Misfire cylinder two

p0335 CKP Sensor 'A' Circuit Malfunction

p0385 Crankshaft Position (CKP) Sensor B Circuit

p0386 Crankshaft Position Sensor B Circuit Range/Performance

Make sure your crankshaft sensor is plugged in or replace the sensor if the plug is good.

Jun 05, 2011 | 2001 Oldsmobile Aurora

1 Answer

2002 PT Cruiser. Vehicle shut down while driving. Received P0340 Trouble code..No camshaft position sensor signal at pcm. I replaced Position Camshaft Sensor, book suggests life on these 5-10 years, It...


This could be related to a loose camshaft drive belt. If you have slack in the belt the camshaft will rebound on over run causing the P0340. It can also be a Crackshaft sensor problem too.(P0335) Hope this helps...

Mar 06, 2011 | 2003 Chrysler PT Cruiser

1 Answer

2002 Mitsubishi Galant 2.4 with repeating error codes P0335,P0340


Check your timing marks , you may have jump the tooth on a timing belt.

May 10, 2010 | Mitsubishi Galant Cars & Trucks

1 Answer

Code p0340 need location on 2004 sebring 2.7 v6



P0340 OBD-II Trouble Code
Technical Description
Camshaft Position Sensor Circuit Malfunction


What does that mean? This indicates that a problem was detected in the camshaft position sensor circuit. Since it says circuit, that means the problem could lie in any part of the circuit - the sensor itself, the wiring, or the PCM. Don't just replace the CPS (camshaft position sensor) and think that will definitely fix it.

Symptoms
Symptoms can include:
  • Hard starting or no start
  • Rough running / misfiring
  • Loss of engine power

Causes A code P0340 could mean one or more of the following has happened:
  • a wire or connector in the circuit could be grounded/shorted/broken
  • the camshaft position sensor may have failed
  • the PCM may have failed
  • there exists an open circuit
  • the crankshaft position sensor may have failed

Possible Solutions With a P0340 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:
  • Visually inspect all the wiring and connectors in the circuit
  • Check for continuity in the circuit wiring
  • Check the operation (voltage) of the camshaft position sensor
  • Replace the camshaft position sensor as required
  • Check the crankshaft position circuit as well
  • Replace circuit wiring and/or connectors as required
  • Diagnose/replace the PCM as required

Also, the cams/crank are out of alignment, thats why you are getting a cam position code (P0340). For more details about your model, you can visit autozone.com (free register)

Hope helped whit this (remember rated this help) Good luck.

Oct 23, 2009 | 2004 Chrysler Sebring

2 Answers

Crankshaft Position Sensor Error P0335 recurred after r&r


In the kit there are two sensor that look identical. The one for the crankshaft has a white paint mark on it near the bolt hole. Make sure that it is in the right location.

Jul 25, 2009 | 2003 Nissan Altima

2 Answers

I have a 2000 Mitsu. Galant. Trouble codes p0335 and p0340 for cam and crank sensors.Are there any common problems?


Hi, I found a couple of good articles on those codes. Rather than just copy and paste here are the links:

P0335 - Crankshaft Position Sensor Electrical Error
http://www.bba-reman.com/content.aspx?content=NEXT_DTC_P0335

P0340 - Camshaft Positio Sensor Circuit Malfunction
http://www.obd-codes.com/p0340

Jan 03, 2009 | Mitsubishi Galant Cars & Trucks

1 Answer

Trouble code p0335


Well thats a crank-shaft position sensor, if you didn't know. I have a mitsubishi but don't know a whole lot about this problem. But this might help:

http://www.club3g.com/forum/problem-reports/89234-p0335-crankshaft-position-sensor-circuit-malfunction.html

Aug 16, 2008 | Mitsubishi Eclipse Spyder Cars & Trucks

Not finding what you are looking for?
2002 Mitsubishi Eclipse Logo

1,539 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...