Question about 1995 Toyota Corolla

1 Answer

I need to know how to replace the ball of the drum front driver side

Posted by on

  • Jeremy W.
    Jeremy W. Feb 23, 2012

    not sure what you are trying to do?

  • yadayada
    yadayada Feb 23, 2012

    ball of the drum?? what would that be exactly?

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Toyota Master
  • 975 Answers

The what?

Posted on Feb 24, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the easiest way to replace the front drivers side lower ball joint on a 1998 Nissan Altima?Or would it just be easier to replace the lower control arm?The ball joint is definetly done-for.


just need to get a ball joint splitter , pronged shaped device that you hammer between the ball joint and control arm ,after stripping down the assembly, little tip, when fitting new ball joint apply slight pressure from below when tightening the nut , this will stop the joint from just spinning , i usually use a scissor jack for this

Jun 03, 2017 | Nissan Cars & Trucks

1 Answer

The driver side front tire wobbles


have u had your car lined up at a aliment shop if not your toe end and camber could be not adjusted right

Feb 11, 2013 | 1997 Mercury Cougar XR7

1 Answer

4x4 driver side front popping hard and wheel tilted


Not unless it needs to be replaced. You can buy the ball joints without the arms.

Aug 28, 2012 | GMC Jimmy Cars & Trucks

1 Answer

How do i replace the front axle seal drivers side n a 2004 escalade


remove axle nut, remove lower ball joint nut, pop drive shaft loose with punch or wood dowel , pop lower ball join from knuckle pull up push axle out of knuckle , pull back knuckle and tie in place pop out axle with big screwdriver or pry bar ,remove seal replace.

Aug 01, 2012 | 2004 Cadillac Escalade

1 Answer

Hyundia matrix 1.6 is it hard to change a drivers side ball joint ?


It is very difficult and requires special tools and skills, you will also need to have the front end aligned after the part change.

Jan 16, 2012 | Cars & Trucks

1 Answer

2000 Ford Taurus driver's side front wheel has too much play side to side.


Worn ball joints, they need to be replaced also replace the ti-rod. You should replace both sides not just the drivers side. If you find too much play in the control arms and replace them you will need to have an wheel alignment done. If there is squeaking noise then the bushings should be changed. If you have not done any work on the front end in 10 years I would also change the wheel barrings if older then five years.

Oct 08, 2010 | 2000 Ford Taurus

3 Answers

How many ball joints does a 99 dodge stratus have?


It has two,lower ball joints,one on each side.

Feb 11, 2010 | 1999 Dodge Stratus

1 Answer

I need to change a ball joint on an avenger


I think that is only available as the control arm assembly. Check whth you local parts store.

May 04, 2009 | 1998 Dodge Avenger

3 Answers

Front end problem


going in drive way noise that most of time upper ball joint you can have a stabilisator link that worn i suject you get that ball joint check again i dont like that noise hope its a fixya for you and me thanks pierre

Jul 26, 2008 | 1998 Chevrolet Blazer

Not finding what you are looking for?
1995 Toyota Corolla Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...