Question about 2003 Oldsmobile Alero

1 Answer

How do i remove and replace drivers side door window

Can the track or channel on window be removed and replaced without takeing the window out? regulator goes up and down without the glass

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Oldsmobile Master
  • 5,370 Answers

For Doors not getting open with remote or key problem,there are help links provided below.Click the link below to go through its procedure and troubleshoot the problem:----
drivers side front door will not open from inside or outside?


Car door will not close?


All power door locks not working ?


Repairing car Door lock Actuator?
How to Access car door panel?


Vehicle door panel components?

Truck Door will not close?

Where is Cars Door control Module located?

Power door locks not working?

Door ajar light stays on?

Door locks not working?

Front Door dis-assembly diagram?

Rear Door dis-assembly diagram?

How to test Power door locks?

Doors will not open with Remote?


How to replace Door Hatch ?


How to remove Doors?


How to Replace Doors?


Remote will not unlock Rear door?


Door locks or windows not working on car?


This will help.


Posted on Feb 29, 2012


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 295 Answers

SOURCE: how remove the rear inside door panel on a 2001 oldmobile aurora

The inner door panel is held in by clips and screw.
Look at the door near the door handle there should be screws holding it in and along the outer edge of the door. Once loose, and the door handle removed or the arm rest removed. The door panel then prys out , because of the clips that hold it on. Then pops out by applying pressure to the panel upward to the top of the door. The clips always break because of the design and plastic.

Good luck

Posted on Mar 21, 2009

  • 67 Answers

SOURCE: trying to reinstall rear driver side door glass.

take the track loose put window in and reinstall track

Posted on Mar 17, 2010

  • 8273 Answers

SOURCE: passenger side rear window is off track, will not

Please see my tip at . These are generic instructions. If you get stuck or need specific instructions for your car, please get back to me with model, year and engine info.

Posted on Oct 10, 2010

  • 14036 Answers

SOURCE: glass fell 99 olds 2

glass fell down in door bolt to equalizer arm to regulator fell out of place missing or window regulator have to remove door trim panel. you need a haynes repair manual to show you how to remove door trim panel. and door panel screws location to door need see screws location to remove power windows and door lock will need door panel trim removal tool.

Posted on Jun 06, 2011

  • 611 Answers

SOURCE: need the plastic clips

check out or u can get them from the dealer

Posted on Sep 20, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I replace the drivers side window on a 1999 saturn s series car (manual)

Remove inner door panel and remove the glass that is left in the window track. Apply glue and place new glass in track and give it plenty of time to dry and set. Then replace inner door panel after all is fine.

Sep 29, 2016 | Saturn Cars & Trucks

1 Answer

How do I remove and install driver window weather strip on 1985 Chevrolet el camino?

The best way is remove the door panel and take out the glass. Part of the track is bolted in and some of it just presses into the channel. Any of the seals across the top of the door, like if the window is down and your arm is resting on them. These just pry off and push back on.

Sep 22, 2014 | Cars & Trucks

1 Answer

Replace bashed in passenger side window

one screw at handle two on arm rest or under switch the rest is plastic retainers just putt and use trim tool or screw driver two bolts hold glass to regulator have to lower window till you see then remove remove bolt that holds front track and slide glass in top and put in track front an back set in regulator and bolt in raise then bolt front track

Aug 04, 2012 | 1995 Volvo 960

1 Answer

The windows on the front driver and front passenger doors are off track. Is there any way to open the doors and take the panel off to get to the harness?

what do you mean off track are they jammed in the door panel or do you mean they work once in a while if they are out of the channel you take your door panel off and remove the window and reinstall in the track make sure you lube the track because sometimes the window jams because the channel is to dry and causes the window to stick if you are saying the windows work once in a while the harness at the drivers side usaully breaks in the rubber garment so you have no choice to take panel off and try to remove the garment and chk your harness to repair cut wires if worst to worst you can cut the rubber garment with a exato knife be careful not to cut other wires and cause a greater problem then when you fix the wires you can tape up the old garment but i need more imfo

Dec 31, 2010 | 1998 Pontiac Grand Prix

1 Answer

How to get to drivers side window to repair it off track pontiac grand am 1999


First you have to remove the door panel .Once the panel off, unplug the window motor and use a volt meter on the plug that plugs into the motor.Push the up/down button and check whether you get about 12 volts, if you do then your motor needs to be replaced. If not then the problem the main control switch on the driver door. You have to remove the motor in order to get that window up.

Thank you !!

The vinyl welt or glass run channel is curled up in the track binding the window glass fron coming up. After it sits for a minute or two like you stated it works its way up a little more each time. The reason is the curled up welt (vinyl) has to takes sometime to work its way back out somewhat. Then it will go up a little more and quit and so on as you said. To fix this you can add a lubracant called dri slide which will work possibly only if your window is fully up at that time. You will need to saturate it between the glass and the run channel (welt) that is curling up causing it to bind. I would do both sides for good measures. If this does not work to greta all you can do is to replace the welt for the glass run channel.

Jun 15, 2010 | 1999 Pontiac Grand Prix

1 Answer

How do I remove driver side door window

You need to remove inner door panel by unscrewing the screws on inner door handle and take a flat screw driver wedge it between the panel and door use flash light to see the clips along the sides and lower part of door and pry them free. then look through the inner door cut outs to find window track. Once you see it use ratchet or screw driver and loosen the window free form track. Then carefully remove window.

Apr 01, 2010 | 2003 Mazda MPV

1 Answer

How to replace driver side power window motor and regulator

remove door handles and door panel then remove rivits that hold the track assmbly and remove glass from track take it all the way out the door and then wiggle the track and motor assmbly out

Jan 13, 2010 | 2005 Lincoln Aviator

1 Answer

Driver window off track need to take door panel off how?

On vehicles without power windows, place a soft cloth under the window regulator handle and pull upwards on the cloth to release the snapring. Remove the regulator handle and plate.

Fig. 2: Using a taped prytool, carefully remove the bezel portion of the handle

46f6882.jpg Fig. 3: Remove the bezel by pulling towards the tip of the handle

9b11f67.jpg Fig. 4: Remove any screw covers . . .

Mar 31, 2009 | 1993 Toyota Camry V6

1 Answer

Window off track driver side 1997 sebring

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Mar 23, 2009 | 1997 Chrysler Sebring

1 Answer

Window jumped off window track

drivers window?
the best way to fix it is to replace the window run channel (rubber the glass slides in) and the regulator. or to get by if the regulator isnt bent take the door panel off, take the door glass out, the front of the run channel inside the door is bent foreward a little bend the metal track to the rear a little by hand, careful its weak, spray the run channel with silicone spray and reinstall the glass. if the run channel is torn it wont last.

Dec 18, 2008 | 2000 Honda Civic

Not finding what you are looking for?
2003 Oldsmobile Alero Logo

405 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts


Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides