Question about Hyundai Motor 2002 Sonata

Open Question

How to replace front wheel bearing on 2003 sonata

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: Had my front wheel bearings replaced today, but now I'm wondering...

it is normal for a garage to mark parts up after all do you think you think you pay the same for grocieries as the store or for that matter can you buy hamburger at aburger joint as cheap as you can at a store a garage has overhead just like any other busines the labor seems alittle excesive but alot of that depends alot on where you live and what it cost to run the shop that is probably a3.5 or 4.0 hr joband i dont know anyone under about 50.00 hr in my aera

Posted on Oct 01, 2008

Ad
  • 393 Answers

SOURCE: replacing rear wheel bearings on 1999 hyundai sonata

  1. for drum brakes with sealed hub(all one piece) remove lug nuts and wheel.
  2. spray penetrating oil around studs if there is a big phillips head screw visible remove it with impact driver/if not use big ballpeen hammer ,tap on flat of drum near studs(becareful not to hit them) until drum loosens(your creating a shockwave to loosen rust)
  3. once drum is off there are 4-bolts coming in from behind backing plate, remove them then hub should be able to be removed w/a little persuation from hammer.
with out sealed hub ,
  1. remove wheel
  2. remove dust cap,cotterpin,star washer(if equipped) do not re use cotter pin
  3. remove nut then washer, wiggle brake drum and front bearing will come out.
  4. put nut on shaft tighten 2-3 turns grab drum by sides and pull towards you this should remove drum leaving inner bearing/seal on shaft
  5. to replace reverse procedure making sure to pack new bearings w/grease(take drum and use long punch to remove bearing races, use race/seal installer to install new races
with disk brakes

  1. remove wheel
  2. remove caliper/bracket
  3. remove rotor
  4. remove 4-bolts from behind,tap old hub out
  5. reverse procedure



Posted on Nov 15, 2008

emissionwiz
  • 76649 Answers

SOURCE: Change front wheel bearings

u will need to remove the brake cailper and the the brake rotor, then the hub retaining nut, that is a large metric nut, the bearing and hub must come off, then u will need to take this hub to a machine shop or the dealer and have the new bearing pressed in.
BCA/NATIONAL Part # 510078 moreinfo.gif {Ball Bearing Bore=1.5354" Outer Diameter=2.9134" Width=1.4173"}
Front Wheel PRICE: $47.99, PART SOURCE: Rockauto.com

3bcf37f.jpg

Posted on Mar 12, 2009

skotkolr
  • 558 Answers

SOURCE: Wheel bearing & drive axel replacement

lift the car support on jack stands remove the wheels remove the brake systems remove the wheel hub locking nut and then remove the strut (this must be compressed or it will hurt you)
remove the axles then when that is complete you need to have the wheel bearings knocked out of the brake hub or removed from the strut assembly and then a new pair reseated, or bolted on then you can assemble in reverse, if you are not mechanically inclined I would recommend a mechanic to do this.

Posted on Apr 07, 2009

emissionwiz
  • 76649 Answers

SOURCE: What does it take to replace the front wheel

the front wheel bearings on your car are not sold except as a front wheel hub assembly with the bearing pre-installed, they run about $100.00 each, to replace them requires no special tools, all u do is remove the wheel, the brake caliper and the brake rotor and the hub nut, then the hub just slides off, u will most likely need a very large socket for the hub retaining nut.

Posted on Jul 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Whats the best way to remove a frozen bearing from front hub for 2003 sonata?


Have it pressed out at a shop. And a new bearing pressed in.

Sep 18, 2013 | Hyundai Motor 2003 Sonata

1 Answer

Could you please tell me the cost to replace rear left wheel bearing on 2004 Hyundai Sonata.


Rear wheel bearing should not be very much. Front would be considerably more. Find a reputable mechanic with a reasonable shop rate. STAY AWAY from car dealerships , they always , always , always overcharge.

Jan 29, 2011 | Hyundai Motor 2004 Sonata

1 Answer

How to replace rear wheel bearing on 2003 hyandia sonata


Hub & Bearing Removal & Installation To Remove:
Hub bearing assembly (Typical) hyundai-08-00-6029.gif

  1. Release parking brake.
  2. Remove rear wheel assembly.
  3. Remove rear wheel speed sensor from carrier.
  4. Dismount brake caliper and support with mechanic's wire.
  5. Remove brake disc.
  6. Remove 4 axle hub mounting bolts. Special tool 09432-11000 (Typical) hyundai-08-00-6021.gif

  7. Using tool 09432-11000 (or suitable gear puller), remove tone wheel.
  8. Remove carrier.
  9. Remove stakes and remove flange nut.
  10. Support bearing outer race flange and press rear axle hub out.
  11. Using tool 09432-11000 (or suitable puller), remove inner race from axle hub.
To Install:
Hub bearing assembly (Typical) hyundai-08-00-6029.gif

  1. Apply thin coat of grease to bearing contact surface and hub.
  2. Using and appropriate tool, press bearing into hub. CAUTION
    Do not press against outer race of wheel bearing.
  3. Install flange nut and stake nut until it meets concave portion of spindle.
  4. Install carrier.
  5. Use an appropriate tool to press tone wheel.
  6. Install hub/bearing assembly with rounded portion of outer race facing up.
  7. Install 4 hub/bearing assembly bolts and rotate hub to seat bearing.
  8. Measure wheel bearing starting torque with a spring balance or equivalent device.
    • Starting torque should measure 15.9 in lb (1.8 Nm) or less
  9. Install brake disc.
  10. Mount brake caliper.
  11. Install rear wheel speed sensor to carrier.
  12. Install rear wheel assembly.
prev.gif next.gif

Oct 28, 2010 | 2001 Hyundai Sonata

1 Answer

My front brakes make a squelling noice when i turn left on my 2003 hyundai sonata


have the area inspected. Look for loose wheel bearings and for anything worn.

Sep 26, 2010 | Hyundai Motor 2003 Sonata

1 Answer

How do I change the front wheel bearing in a 2001 Sonata 6 cyl


jack the front off the ground remove the tire remove the brake caliper remove the rotor remove the bolt hol;ding the front axle into the spindle hub, remove the hub and bearing.

May 06, 2010 | 2001 Hyundai Sonata

1 Answer

How do i replace rear wheel bearings


the rear wheel bearing is part of the rear hub and not serviceable the hub itself needs to be replaced, its fairly simple, and not that expensive,you must remove the brake caliper and rotor to remove it.

Nov 25, 2009 | Hyundai Motor 2003 Sonata

1 Answer

How to replace front wheel bearing 2009 Sonata


No way ,its a strip the the whole hub unit off and there is a circlip coming in from the back ,which is the way the bearing is pushed out ,NO HAMMERS

Oct 23, 2009 | 2006 Hyundai Sonata

2 Answers

Fixing a 2003 ford focus front wheel bearings


remove the hub and spinle ,tie rod end ,axle nut.ball joint,and seperate from strut and then have new bearing pressed in...or rent a bearing press that works with an impact wrench,but they are a little hard to work with...good luck...lee

Sep 07, 2009 | 2003 Ford Focus

1 Answer

How do you remove front wheel bearings


this is a big job it requires a press. you must remove the knuckel assembely as a hole press out the hub remove a snap ring on the inner side of the knuckel then press the bearing out instalation in reverse i do not recomend trying this at home the going rate at most shops is 1.5 hours per side

Oct 19, 2008 | Hyundai Motor 2003 Sonata

1 Answer

Replacing rear wheel bearings on 1999 hyundai sonata


  1. for drum brakes with sealed hub(all one piece) remove lug nuts and wheel.
  2. spray penetrating oil around studs if there is a big phillips head screw visible remove it with impact driver/if not use big ballpeen hammer ,tap on flat of drum near studs(becareful not to hit them) until drum loosens(your creating a shockwave to loosen rust)
  3. once drum is off there are 4-bolts coming in from behind backing plate, remove them then hub should be able to be removed w/a little persuation from hammer.
with out sealed hub ,
  1. remove wheel
  2. remove dust cap,cotterpin,star washer(if equipped) do not re use cotter pin
  3. remove nut then washer, wiggle brake drum and front bearing will come out.
  4. put nut on shaft tighten 2-3 turns grab drum by sides and pull towards you this should remove drum leaving inner bearing/seal on shaft
  5. to replace reverse procedure making sure to pack new bearings w/grease(take drum and use long punch to remove bearing races, use race/seal installer to install new races
with disk brakes

  1. remove wheel
  2. remove caliper/bracket
  3. remove rotor
  4. remove 4-bolts from behind,tap old hub out
  5. reverse procedure



Jul 19, 2008 | 1999 Hyundai Sonata

Not finding what you are looking for?
Hyundai Motor 2002 Sonata Logo

Related Topics:

160 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...