Question about 2003 Chevrolet Impala
Dash light in the heat and air switch out?
You will need to pull the control head out and replace the tiny bulbs that are hard wiried to the circuit borad inside, this requires very good skills in solder repair. The light bulbs are available from Radio Shack, the part number is 7219
Posted on Feb 23, 2012
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
If by low air air pressure, you mean the tire pressure sensor, here is the way to reset.
To reset (calibrate) the system: The tire pressure
monitor system can be reset two ways. With the ignition position at ON, pull the interior lamps control to the ON and OFF settings three times. It can also be reset through the radio using the
1. Turn the ignition to ACC or ON and turn the radio off.
2. Press and hold the TUNE DlSP button on the radio for at least five seconds until SETTINGS is displayed.
3. Press the SEEK SCAN up or down arrow to scroll through the main menu.
4. Scroll until TIRE MON appears on the display.
5. Press the 1 PREV or 2 NEXT button to enter the submenu. RESET will be displayed.
6. Press the TUNE DlSP button to reset. A chime will be heard to verify the new setting and DONE will be displayed for one second.
7. Once the monitor has been reset, scroll until EXIT appears on the display.
8. Press the TUNE DlSP button to exit programming. A chime will be heard to verify exit.
The system completes the calibration process during
driving. The system normally takes 15 to 20 minutes of driving
in each of three speed ranges to "learn" tire pressures. The speed ranges are 15 to 40 mph (25 to 65 km/h), 40 to 65 mph (65 to 105 km/h) and above 65 mph (105 km/h). When learning is complete, the system will alert you after two to eight minutes if a tire is 12 psi (83 kPa) different from the other three tires. Detection thresholds may be higher and detection times may
be longer on rough roads, curves and at high speeds. The system is not capable of detection at speeds greater than 70 mph (110 km/h).
Almost all of the message center items are accessed through the menu on the radio. You should be able to find what you need be getting in the menu and looking around. Hope this is what you were looking for?
Posted on Aug 10, 2008
Try under the dash, attached to colum is a switch that the rod goes into from your ignition key switch, that may need to be adjusted tword your steering wheel just a touch, they go out of alignmnet from time to time
Posted on Sep 15, 2009
After you replace the ignition switch turn the key to start the car and release leave the key were it stops after trying to start wait 10 minutes until security light goes out turn key to full off position then repeat the above procedure two more times for a total of three on the 3rd attempt to start car wait for light to go out then turn key to full off positoion wait 10 seconds then try to start car body control module should learn new pass code and the car should start.
Big john, J@J Automotive
Posted on Mar 02, 2010
check and see if you have power to your switch, it might just be a fuse. worse case is you'll have to change the actual lights. was it starting to get dimer and dimmer?
Posted on Jun 04, 2010
Tips for a great answer:
Oct 19, 2016 | 2003 Chevrolet Impala
Aug 31, 2012 | 2003 Chevrolet Impala
Sep 12, 2011 | 2003 Chevrolet Impala
Mar 27, 2011 | 2003 Chevrolet Impala
Sep 22, 2010 | 2003 Chevrolet Impala
Jul 22, 2010 | 2003 Chevrolet Impala
Apr 15, 2010 | 2003 Chevrolet Impala
Oct 02, 2009 | 2002 Chevrolet TrailBlazer
Sep 15, 2009 | 2003 Chevrolet Impala
Dec 30, 2008 | 2003 Chevrolet Impala
264 people viewed this question
Usually answered in minutes!