Question about Cars & Trucks

Open Question

International 8100 truck rear axle nut torque specs

Axle nut torque specs

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 15 Answers

SOURCE: what are the front axle nut torque specs for a

185 ft.lbs

Posted on Oct 10, 2009

Ad
chuck943
  • 783 Answers

SOURCE: torque specs 7.5 inch rear axle 96 ford ranger

Differential bearing caps 70-85 ft lb
Ring gear bolts 70-85 ft lb
Pinion bearing preload if using original bearings 8-14 lb-in, if installing new bearings 16-28 lb-in

Posted on Jan 30, 2009

  • 99 Answers

SOURCE: What are the torque specs

the torque are not mention out side any authorised workshop for that you need to visit the nearest authorised dealer or service centre & leave the rest of work to them without any hazard or trouble or either can start from a torque of 25 to 45 lbs. do not exeed the limit or other wise the nut or even the Axel can get broken in the prossess of facinating it so till then my friend have happy motoring & see you soon.!

Posted on May 08, 2009

warlock61
  • 659 Answers

SOURCE: Axle nut torque spec

184 ft/lb

Posted on May 11, 2009

  • 599 Answers

SOURCE: torque specs on replacing cv axle on 05 Pacifica

ok here we go tie rod=55 ft lbs axel nut= 180 ft lbs strut bolts= 65 ft lbs plus 90 degrees

Posted on Jan 07, 2010

Testimonial: "thank you very much!!!!!!!!!!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the torque specs for the rear hub assembly axle nut on a 1997 honda accord with drum brakes


You can look in your owners manual for torque specs, it list all torque values for the vehicle.

Dec 04, 2015 | 1997 Honda Accord

1 Answer

What is the torque spec for the rear wheel hub bearing nut?


Torque spec is 200Nm / 148 ft lbs for the axle nuts front and rear

May 02, 2015 | 2005 Ford Freestyle SEL

1 Answer

97 F250 HD Rearend axle bearing retaining nut Torque Spec for used bearings. It is 10.25 sterling rear gear w/ 7.3L diesel eng.


Axle retaining nut torque spec is 55 to 60ft lbs. back off 5(new) or back off 8(used) clicks, and axle retaining bolts 60-80ft lbs in criss cross pattern.

Apr 25, 2011 | Ford F-250 Cars & Trucks

1 Answer

Need torque specs on axle nuts for dana 50 rear axle


Dana 50 Front Axle

Observe the following torques;

* Left and Right drive axles-to-cross member: 120-150 ft. lbs. (163-203 Nm)

* Axle arm-to-radius arm: 180-240 ft. lbs. (244-325 Nm)

* Coil spring insulator: 30-70 ft. lbs. (41-95 Nm)

* Upper spring retainer: 13-18 ft. lbs. (18-24 Nm)

-----------------------------------------------

Dana 60 Front Axle

Observe the following torques;

* Drive shaft-to-flange: 15-20 ft. lbs. (20-27 Nm)

* Track bar nut and bolt: 160-200 ft. lbs. (217-271 Nm)

* Stabilizer link nut: 20-30 ft. lbs. (27-41 Nm)

* Stabilizer barU-bolt: 50-65 ft. lbs. (68-88 Nm)

* Spindle connecting rod-to-knuckle: 70-100 ft. lbs. (95-136 Nm)

* Front spring U-bolt: 95-100 ft. lbs. (115-135)

Feb 19, 2011 | 1986 Ford F 250

1 Answer

I need the torque specs on a rear axle pinion nut for a 2003 Dodge Ram 2500 4/4 Cummins, Automatic.


The pinion nut does not have a torque spec. as in how tight the nut is. The amount of torque is measured in bearing preload. You will need a "torque to rotate" torque wrench. If you are using new bearings the torque spec. is 15-25 in. lbs. If you are using your old bearings the torque spec. is 10-20 in. lbs to rotate. To measure this you will need to tighten the nut in small increments then use the torque to rotate wrench to turn the pinion without the carrier/ ring gear installed. Repeat until desired torque is reached.

Jan 29, 2011 | Dodge Ram 2500 Cars & Trucks

1 Answer

Replaced rear axle pinion bearing and seal, need to know pinion nut torque spec. for aam rear axle 2005 dodge 3500 4x4 Thanks.


There is no torque specs,this nut has to be tightened back like it was ,the best thing to do,was,to late now,is to use a torque wrench to remove the nut,and remember the torque,and when replacing it,torque it back to that spec,the reason being,there is a crush sleeve between the front pion bearing ,and the rear pinion bearing,and it has to be crushed to a certain amount,to aquire deepness into the ring gear,anyway just give it about 25 lbs torque,any more the crush sleeve will crush even more and the deepness of the pinion will be too much.

Apr 19, 2010 | 2005 Dodge Ram

2 Answers

Front Hub Bearing Torque specs to complete replacement


THE LUG NUT TORQUE SPEC - 140FT/LBS\
CALIPER MOUNT - 80FT/LBS
CALIPER BRACKET 129FT/LBS
AXLE NUT 177FT/LBS

Apr 24, 2009 | 2003 Chevrolet Silverado 1500

1 Answer

What all do i remove to replace the rear wheel bearings on a 1995


First jack rear end up and block it..Remove the rear tires,Take off caliper and caliper bracket..Next remove the rotor,Then there will be a big nut in the center that the axle is bolted to.Remove that nut..Then make sure thees no wires for abs or any other kind of wires connected to the bearing.Next you should see 3 bolts holding the bearing in maybe 4 they changed them so many times..After removing the bolts you'll probably need a hammer and a chisel or air chisel to get the bearing out..Be careful when doing this to not damage the holder thats holding the bearing it.Go all the way around it with the chisel working all corners to removing the bearing..By now you should have progress on getting it out.Repeat process to installing the new one..Just be very carefull in not ruining the new one and there is a torque spec on the center nut that holds the axle and tightens the bearings preload.Call your local parts store for torque spec on rear axle nut.If you don't get the right amount off torque will result in early failure.Not to tight and not to loose.It not that major and it may seem but will save you money in the end..So dont forget to get the torque specs.Good luck and happy I could help..

Mar 30, 2009 | 1995 Ford Thunderbird

1 Answer

2005 chevy 4x42500hd


Hi..
On your 05 Chevy 4X4 2500HD.
The Pinion Yoke Nut, 9.75" Axle. the torq spec. is 370 Nm. -- 273 Lb ft.

I hope this help on your question.

Thank you for use fixya...

Nov 04, 2008 | 2008 Chevrolet Silverado 2500HD 2WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

398 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...