Question about 1993 Ford Crown Victoria

Open Question

How many o2 sensors dose the crown victoria 1993 have?

How many o2 sensors dose a crown victoria 1993 have?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

97crownvic
  • 28 Answers

SOURCE: crown victoria window motor replacement

remove the door panel. be very careful and make sure you get all the screws out. Should be maybe 2 on the bottom half of the door, and 2 on the top half. one is right by the handle, which is the one i forgot the first time i took my door pannel off. carefully pull the panel upward, and outward at the same time. Once the panel is off, disconnect the controls, and remove the light from the panel. Remove the plastic cover very carefully, it will tear, just keeps noise, and air, and the elements out.
There will be 3 screws, they are torx bolts, once you pull those 3 out. They are located middle of the door towards the right side. The motor will drop down a little bit. disconnect the wires for the motor, and wiggle the motor off of the regulator. the crown vics have a decent size hole to get into the door panel, you can also remove the speaker if that would help you do it. other than that, it just lining up the new motor into the car, pushing it into the regulator, and putting the 3 bolts in, make sure they are snug, and not cross threaded. put everything back together, and your set.

Posted on Mar 19, 2009

CLEONTI
  • 33 Answers

SOURCE: need wiring diagram for 2008 ford crown victoria

Hello,

You can purchase the wiring diagram for $5.99 from the following site: http://www.wiring-diagram.com/. You can also purchase a wiring diagram book from the following link: http://cgi.ebay.com/ebaymotors/2008-FORD-CROWN-VICTORIA-MARQUIS-WIRING-DIAGRAM-MANUAL_W0QQitemZ120394723100QQcmdZViewItemQQimsxZ20090320?IMSfp=TL090320147007r15080.

Hope this helps,

Chris

Posted on Mar 23, 2009

  • 93 Answers

SOURCE: 2000 crown victoria serpentine belt installation

Accessory Drive Component Locationsa0011762.gif

Posted on Jun 09, 2009

  • 1 Answer

SOURCE: 1993 crown victoria

Try changing the mass air flow sensor located up by the air cleaner. Mine had a similar problem when you stepped on the gas it would pop (sounding like a backfire) and hardly had any power. I changed that sensor and it runs strong now.

Posted on Jun 15, 2009

c17hydro
  • 2984 Answers

SOURCE: heater core

No, you don't have to pull the whole dash board but you have to pull a few panels....here is the steps on how to get to it and remove and replace it:

  1. Disconnect the negative battery cable.
  2. Drain the cooling system and disconnect the heater hoses from the heater core tubes. Plug the hoses and the heater core tubes to prevent coolant leakage.

CAUTION NEVER open, service or drain the radiator or cooling system when hot; serious burns can occur from the steam and hot coolant. Also, when draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantities. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old.


  1. Remove the 3 nuts located below the windshield wiper motor attaching the left end of the plenum to the dash panel. Remove the 1 nut retaining the upper left corner of the evaporator case to the dash panel.

935a10f.gif
Plenum removal—1990-98 vehicles

  1. Disconnect the vacuum supply hose(s) from the vacuum source. Push the grommet and vacuum supply hose(s) into the passenger compartment.
  2. Remove the right and left lower instrument panel insulators.
  1. On 1989 vehicles:
  2. Remove the 3 glove compartment hinge screws, disconnect the check arms and remove the glove compartment.
  3. Loosen the right door sill plate and remove the right side cowl trim panel.
  4. Remove the bolt attaching the lower right end of the instrument panel to the side cowl.
  5. Remove the instrument panel pad as follows:
    • Remove the 2 screws attaching the pad to the instrument panel at each defroster opening. Be careful not to drop the screws into the defroster openings.
    • Remove the one screw attaching each outboard end of the pad to the instrument panel.
    • On Crown Victoria, remove one pad attaching screw near the upper right corner of the glove compartment door.
    • Remove the 5 screws attaching the lower edge of the pad to the instrument panel. Pull the instrument panel pad rearward and remove it from the vehicle.
  6. On 1990-98 vehicles:
  7. Remove all instrument panel mounting screws and pull the instrument panel back as far as it will go without disconnecting any wiring harnesses.
  8. Make sure the nuts attaching the instrument panel braces to the dash panel are removed.
  9. Loosen the right door sill plate and remove the right side cowl trim panel.
  10. If equipped with manual air conditioning, disengage the temperature control cable housing from the bracket on top of the plenum. Disconnect the cable from the temperature blend door crank arm.
  11. If equipped with Automatic Temperature Control (ATC), proceed as follows:
  12. On 1989 vehicles, disconnect the temperature control cable from the ATC sensor.
  13. Detach the vacuum harness line connector from the ATC sensor harness and detach the electrical connector from the ATC servo connector.
  14. On 1990-98 vehicles, remove the cross body brace and disconnect the wiring harness from the temperature blend door actuator. Detach the ATC sensor tube from the evaporator case connector.
  15. Detach the vacuum jumper harness at the multiple vacuum connector near the floor air distribution duct.
  16. Disconnect the white vacuum hose from the outside-recirculating door vacuum motor.

572e87e.gif
Floor air distribution duct removal—1990-98 vehicles
  1. Remove the 2 hush panels.
  2. Remove 1 plastic push fastener retaining the floor air distribution duct to the left end of the plenum.
  3. Remove the left screw and loosen the right screw on the rear face of the plenum and remove the floor air distribution duct.
  4. Remove the 2 nuts from the 2 studs along the lower flange of the plenum.

a3c9f99.gif
Heater core removal—1990-98 vehicles

  1. Carefully move the plenum rearward to allow the heater core tubes and the stud at the top of the plenum to clear the holes in the dash panel. Remove the plenum from the vehicle by rotating the top of the plenum forward, down and out from under the instrument panel. Carefully pull the lower edge of the instrument panel rearward, as necessary, while rolling the plenum from behind the instrument panel.
  2. On 1989 vehicles with ATC, remove the ATC servo from the plenum.
  3. Remove the 4 retaining screws from the heater core cover and remove the cover from the plenum assembly.
  4. Pull the heater core and seal assembly from the plenum assembly.
To install:
  1. Carefully install the heater core and seal assembly into the plenum assembly. Visually check to ensure that the core seal is properly positioned. Position the heater core cover and install the 4 retaining screws.
  2. On 1989 vehicles with ATC, install the ATC servo on the plenum.
  3. Route the vacuum supply hose through the dash panel and seat the grommet in the opening.
  4. Position the plenum under the instrument panel with the register duct opening up and the heater core tubes down. Rotate the plenum up behind the instrument panel and position the plenum to the dash panel. Insert the heater core tubes and mounting studs through their respective holes in the dash panel and the evaporator case.
  5. Install the 3 nuts on the studs along the lower flange and one on the upper flange of the plenum. Install the 3 nuts below the windshield wiper motor to attach the left end of the plenum to the dash panel and the one nut to retain the upper left corner of the evaporator case to the dash panel.
  6. Position the floor air distribution duct on the plenum. Install the 2 screws and plastic push fastener. If removed, position the panel door vacuum motor to the mounting bracket and install the 2 attaching screws.
  7. Connect the white vacuum hose to the outside-recirculating door vacuum motor. Attach the vacuum jumper harness to the plenum harness at the multiple vacuum connector near the floor air distribution duct. Install the floor duct.
  8. If equipped with manual air conditioning, connect the temperature control cable housing to the bracket on top of the plenum and connect the temperature control cable to the temperature blend door crank arm. Adjust the temperature cable.
  9. If equipped with ATC, proceed as follows:
    1. On 1989 vehicles, connect the temperature control cable to the ATC sensor and adjust the cable. Route and attach the vacuum harness connector to the ATC sensor and attach the electrical connector to the ATC servo connector. Do not block the sensor aspirator exhaust port with the excess vacuum harness. Install the ATC sensor tube between the sensor and the evaporator connector.
    2. On 1990-98 vehicles, attach the ATC sensor tube to the evaporator case connector. Install the cross body brace and connect the wiring harness to the blend door actuator.
  10. Install the bolt to attach the lower right end of the instrument panel to the side cowl. Install the right side cowl trim panel and tighten the right door sill plate attaching screws.
  11. On 1989 vehicles, install the instrument panel pad and the glove compartment door. On 1990-98 vehicles, push the instrument panel back into position and install all instrument panel mounting screws. Install the right and left lower instrument panel insulators.
  12. Connect the vacuum supply hose(s) to the vacuum source.
  13. Install the right and left lower instrument panel insulators and install the 2 hush panels.
  14. Unplug the heater core tubes and the heater hoses and connect the heater hoses to the heater core tubes. Fill the cooling system.
  15. Connect the negative battery cable and check the system for proper operation.

Posted on Feb 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I change o2 sensor in a 1994 Ford crown victoria?


Unscrew it like a spark plug

Need a 22 mm wrench or O2 Socket

Oct 01, 2014 | 1994 Ford Crown Victoria

1 Answer

Crown victoria kill switch?


Take it to the dealer, there is nothing you can do.

Mar 24, 2014 | 1993 Ford Crown Victoria

1 Answer

1992 ford crown victoria idel problem


sounds like o2 sensors or needs a tune up

Mar 22, 2014 | 1998 Ford Crown Victoria

1 Answer

My 94 Ford Crown Victoria cuts out when I give it some gas. It idles fine, but when I put my foot down on the gas pedal it does not what to go, it cuts out.


Test the TSP -throttle position sensor
on throttle body

May want to remember if your O2 Sensor is
over 100,000 miles & when you changed your
fuel filter ( 3 years,30,000 miles)

How old are the spark plugs, more than 4 years
or 60,000 miles

Test EGR Valve

Jun 10, 2011 | 1994 Ford Crown Victoria

1 Answer

1993 crown victoria


Try changing the mass air flow sensor located up by the air cleaner. Mine had a similar problem when you stepped on the gas it would pop (sounding like a backfire) and hardly had any power. I changed that sensor and it runs strong now.

Mar 21, 2009 | 1993 Ford Crown Victoria

1 Answer

My speedometers does not work


Check the speed sensor at the tranny.Get a trouble code at any autoparts store.

Feb 06, 2009 | 1993 Ford Crown Victoria

Not finding what you are looking for?
1993 Ford Crown Victoria Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...