Question about Hyundai Motor 1999 Elantra

Open Question

My 1999 Elantra turn signal switch and hazard light do not work?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

maklean
  • 1665 Answers

SOURCE: turn signals /hazard lights don't blink

Hi! check first for any blown fuse. INSPECTION 1. Check for a burnt fusible link with an ohmmeter. 2. If a fusible link burns out, there is a short or some other problem in the circuit. Carefully determine the cause and correct it before replacing the fusible link. The fusible link will burn out within 15 seconds if a higher than specified current flows through the circuit.2f5ff5a.gif

Posted on Jun 03, 2008

  • 30 Answers

SOURCE: turn signals do not work,

The problem is not with switch.. you need to replace the flasher can or relay.

Posted on Sep 06, 2008

  • 1 Answer

SOURCE: 98 Elantra Turn Signals and Hazards Broken

Check your flasher. The flasher is a round metal thing inside the fuse panel. There are two fuse panels in the 98's, one inside the car by the hood release latch, and one under the hood by the battery. I'm not sure which one the flasher is in, but that definetly sounds like your problem. It simply plugs in like a fuse, and I would say it probably costs less than ten bucks, so I would try that first before anything and even if thats not the problem you only wasted a few bucks. Oh yea on a few cars the flasher might not be in the fuse panel, if it's not in yours its probably under the dash. If you cant find it or don't think you know what it looks like, I would go to the auto parts store and buy the new one, that way you know what your looking for. Good luck, hope this helped you.
-ADAM BOMB-

Posted on Jan 16, 2009

  • 1 Answer

SOURCE: 98 Hyundai Elantra turn signal and hazards only work sometimes.

You need to replace the fuse - have a look at the manual and see which fuse it is buy a new one put it in and it should be fine - the on off thing is where the fuse wire touches and then moves again.

Posted on Jul 27, 2009

  • 166 Answers

SOURCE: Tiburon 04, left turn signal lights stay on

replace the turn signal 'Clicker' also known as the turn signal relay. Most likely the problem unless you have a really wierd electical issue that will be hard to isolate...

Peace,

Posted on Mar 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 Chevy lumina hazard lights do not work


most likely need new muli-function switch

May 29, 2017 | 1999 Chevrolet Lumina

1 Answer

Turn signals and hazards stopped working on 2000 hyundai elantra


If the hazard switch had been removed and replaced for any reason, it may not have been connected properly.ie: a loose connector, If you say that bulbs (and fuse?) are okay, this could be checked.
Lou Arnone (Lucky Elantranian)
P.S.: I love my Elantra. When I bought it more than eleven years ago, it was love at first drive. It's been that way ever since.

Mar 28, 2013 | 2000 Hyundai Elantra

1 Answer

1999 oldsmobile aurora side marker light flash on and off when the car is turned off


Power is appliedat all times through the 20A HZRD/ STOP LPS fuse in the right rear junction block. The ORG wire connects to the hazard flasher and the BRN output wire connects to the A5 terminal of the TURN/HAZARD switch assembly. When the HAZARD switch is engaged, power is applied to the front and rear turn signals and the left and right turn indicators in the instrument cluster, causing them to flash. Obviously an open fuse, a defective flasher, a defective HAZARD switch, or a defective TURN/HAZARD switch assembly will prevent the lamps from flashing. If the turn signals operate normally, they are not the problem.

Sep 05, 2012 | 1999 Oldsmobile Aurora

1 Answer

How to fix no brake light issue on 1999 Expedition


Have you tried wiggling the hazard light switch? The brake light switch puts 12 volts to the hazard/turn signal switch,and the switch will apply this to both taillights.If you turn on the left or right turn signal,it will only route 12 volts to the other light.If you turn on the hazard lights,it will only allow the 3rd brake to come on due to the brake switch.Often.the hazard light/brake light contacts get corroded due to not being turned on and off regularly.Have someone watch the taillights(or use a mirror) to see if they come on when you wiggle the hazard switch.If it does,turn the hazard light switch on and of repeatedly to clean the contacts.

Jul 14, 2012 | 1999 Ford Expedition

1 Answer

Asked this on 12/20 no response so asking again. 95 Hyundai elantra. Turn switch works part time. Put another used switch in but still same issue. When it's out nothing works, no turn, no hazard, no...


Hi,
My 1999 Elantra has a similar problem with the turn signal, I checked the switch itself and it worked fine, eventually I found out that it was the hazard switch that is faulty, to test it try and turn your car on, activate turn signal and press down on the top of the hazard switch or just fiddle with it. Just a thought, worked with mine. Good luck.

Dec 23, 2011 | 1995 Hyundai Elantra

1 Answer

1999 Lincoln Continental was in for repairs and now my turn signals and break lights dont work. Im being told it's something to do with the anti theft system because the battery was unhooked. The...


I suspect there is a problem with the turn signal/ hazard switch. turn the turn signal on left or right, if it doesn't flash, grip the hazard button and gently wiggle it around, if the signals start flashing, replace the turn signal switch. The Brake lights are wired through the turn signal switch, if the 3rd brake light works, the brake switch is OK. I don't think it has anything to do with the anti theft system (at this time)

Sep 21, 2011 | 1999 Lincoln Continental

1 Answer

1998 Lincoln TC no brake or hazard lights work.


Hazard light switch... They all intermingle in operation.
My ex wifes 96TC was doing the same thing... I could OCCASIONALLY get the hazards to work by turning the hazard switch on/off like 10 times in a row and suddenly it would fix... finally bought a new switch

Sep 14, 2009 | 1999 Lincoln Town Car

3 Answers

Turn signals wont work fuses are good?


the hazard switch above the radio is your problem. if you put on your signals and they don't flash turn hazards on then off and they will flash. (changing this *** will fix your problem

Aug 30, 2009 | 1999 Pontiac Grand Am GT

Not finding what you are looking for?
Hyundai Motor 1999 Elantra Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...