Question about 2003 Hyundai Tiburon

Open Question

Clutch pedal went to floor and now it wont press down

Clutch pedal pressed went to the floor, car coasted to a stop. turned off ignition pulled clutch pedal back and now it wont press back down.

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jmassengill
  • 345 Answers

SOURCE: clutch pedal is very heavy to push down

If the clutch in your car is hydralic there is no way to adjust that type of clutch. That you describe the clutch as being hard to push and that you have to have the clutch "right down on the floor to engage a gear" is an indication that the clutch is worn and needs to be replaced. If the clutch in your car is pushed by a cable, the cable might be adjustable and if that is the case you might get a few more months of use from the car, but the fix is still the same, you will need to get a new clutch put in your car.

Posted on Nov 26, 2008

  • 566 Answers

SOURCE: Clutch pedal low near floor, can the clutch be adjusted?

hi the clutch on accent is hydraulic operation so if pedal is very low on disengaging clutch ? you may have a problem with the hydraulics 1st thing to check is fluid level? this is the reservoir that feeds both brakes and clutch but is seperaterated inside if fluid low? top up and bleed the slave cyl however if fluid low indicates a leak ? possibly slave cyl? if no loss of fluid ? then prob may be fault in the master cyl ? check fluid come back with any update please ps if this problem has just occured? check for leaks ?

Posted on Feb 02, 2009

Benimur
  • 6966 Answers

SOURCE: to change gears, I need to fully press down on my

Hi and welcome to FixYa,

In a manual 2001 Hyundai Accent, the clutch cable could be adjusted. The adjustment point is on the cable 'pad' where it enters the firewall in the engine compartment.
86c2d7d.jpg
To adjust, the slack or free play must be decreased. This is done by turning the adjusting nut clockwise. Check back by pressing on the clutch pedal to your preference.
73309c3.jpg
Good luck and thank you for using FixYa.

Posted on Feb 18, 2009

  • 14 Answers

SOURCE: MY CLUTCH STARTED SQUEEKING WHEN PRESSED

dont use wd40 on it that will mess up the clutch the problem is in the throw out bearing when you put your foot on the clutch that ingages clutch and throw bearing together thats where the noise is comimg from bearing need to be replaced but you replace bearing replace everything in clutch

Posted on Mar 11, 2009

  • 566 Answers

SOURCE: 1997 hyandai accent gt clutch problem

hi considering age of car and that you have no leaks on hydraulics? may i suggest you try bleeding the clutch to rid of old fluid a couple of pumps may be suffice ? b/fluid does absorb moisture and heat over time hence recommendation tat fluid be changed at period specified in handbooks ie 12 monthly ?

Posted on May 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Car wont start


is there a cable that hooks to the clutch,it may be broken.it will need to be re attached or replaced if this is the problem

Dec 30, 2013 | 2006 Peugeot 405

1 Answer

97 jeep Cherokee clutch will not depress to start the engine


Now you need to bleed the clutch at the clutch slave cylinder down on the transmission to restore the clutch.
Put a wrench on the bleed valve and open it, then lightly close it. Now have someone pump the clutch a couple of times to build pressure. Then while the clutch pedal is slowly pressed down open the bleed valve, then close valve as pedal gets to floor. Repeat this bleed process until a steady stream of brake fluid comes out the bleed valve. Then you should have a good clutch again.

Dec 20, 2012 | 1997 Jeep Cherokee

1 Answer

Broken clitch cable on 2000 chevy impala...how do u replace it..the wires are broken


see this steps and fix it. God bless you
Clutch Cable Replacement The clutch cable provides a means to "break the drive" between the engine and the wheels. The engine spins constantly, but the wheels do not, so in order to stop a car's wheels without turning off the engine, the wheels have to disconnect from the engine. When the clutch pedal is pressed, the cable disengages the plates, allowing the driver to shift gears or coast without killing the engine.
A failing clutch cable may make the clutch pedal difficult to depress. If the clutch cable fails, the clutch pedal may remain on the floor and not return to its normal position.
To replace the clutch cable, disconnect it from the clutch pedal (usually inside the vehicle) and from the release mechanism or cable attachment that operates the clutch assembly (usually at the transmission beneath the vehicle). A new clutch cable is then installed and adjusted. (The specifics vary according to the vehicle and range from straightforward to very difficult.)

Oct 04, 2012 | Cars & Trucks

2 Answers

Clutch pedel stuck on floor


The clutch master has blown out

Jan 19, 2010 | 1990 Ford F250

3 Answers

When I was at a stop light, I went to put it in first gear when the light turned green. When I did, the clutch pedal just went straight to the floor, and stayed there. It doesn't seem to be the clutch...


The thrust bearing could have collapsed or the Fingers on the clutch plate have gone.

If when you press down on the clutch the cable moves the arm on the clutch housing then it is either of the above

Aug 19, 2009 | 1998 Volkswagen Jetta

1 Answer

Clutch pedal stuck to the floor


hi, there is one place you should check. but answer this first, did you swap the car with a new engine or did you pull the engine out of the car? if the anwser is "yes" then you'll probably twist a fluid tube for the clutch at the tranny. so check the front end of the tranny, it should be a short metal wire (tube like) that should be connection to the tranny. the bolt size is 8mm. so find that tube and open the line. then ask someone to pump the clutch pedal 3 or 4 time and stop while holding it down. yes! the clutch fluid should be coming out while he's doing that. so now when he's press down the last pump, you should twist it back on. repeat it, over and over until you get it to harden again. you should also open the clutch master cylinter, too and refill some more... well hope this help...

Oct 04, 2008 | 1994 Acura Integra

2 Answers

Clutch


believe it or not, the floormat on my 2000 Sunfire will sometimes slip forward and hold the clutch pedal down against the floor. It truly feels like a mechanical problem, but simply pull the floormat away and the pedal pops right back up!

Jun 29, 2008 | 2004 Pontiac Sunfire

1 Answer

Clutch problem


check the fluid level first, if its empty this will happen, if so full it and bleed the clutch, if not it could be the slave cylinder and failing both, it could be the clutch itself, easiest way to check is to see on the gearbox if the clutch is engaging when you press the pedal down.
just ask if you need more help

Jun 17, 2008 | 1998 Honda Accord

Not finding what you are looking for?
2003 Hyundai Tiburon Logo

Related Topics:

172 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...