Question about 1996 Dodge Grand Caravan

1 Answer

How to install sliding door glass window

Window in sliding side door nedds to be replaced-how to install it?

Posted by Anonymous on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Installing windows or doors at your own is not so easy and also risky too. There are various service providers providing such repair and replacement services at minimal cost. Windows and Doors repair and replacement services are also available online. http://windowmedics.com/

Posted on Aug 02, 2017

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1779 Answers

SOURCE: rear sliding glass window

If u r going to buy a new one, instructions will be included, if u have plans to purchase a used one from a salvage yard, they aren't too difficult to install, the worst part is removing the old glass, and that's already done! Rubber glass seal around outside should be in place, put a rope inside the seal (where the glass will go) leaving a couple of feet or more hanging out at the end. Put the glass in between seal edges as much as you can w/out forcing. W/ a helper, slowly pull the rope out as u push the glass into the seal, the rope pulls back the seal so the glass can slide into the channel. If u have any trouble, don't insert the rope all the way around, this way more of the glass will fit in the rubber channel (seal). Good luck, let me know how it works for u. countrycurt0

Posted on Oct 09, 2008

stevehinrich
  • 61 Answers

SOURCE: drivers side window

The glass should bolt to the window channel on the bottom of the window. Roll the window all the way up and duct tape it to the top of the door.

Posted on Mar 03, 2009

Hightower971
  • 183 Answers

SOURCE: how to change glass of

take it to a shop

Posted on Apr 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Steps to replace right hand side door internal window seal


I believe your car has a full frame windows? If that is correct then are you talking about the rubber the window glass slides up and down in? If so, then you have to remove the inner door panel and might be helpful if you have power windows remove the power window switch from the inner panel and reconnect to wiring harness. Using this technique, there are 2 10mm bolts holding the window glass to the regulator. Position the glass with the 10mm bolts through a couple sight holes, remove the 10mm bolts but hold on to the glass so it doesn't fall in the door and break. install the rubber window channel and reverse procedure.

Dec 28, 2011 | 1990 Honda CRX

1 Answer

How do I install a new front door RH window? My parents front passenger side window was damaged. I can obtain one however, I need to install it and remove the broken glass that has fallen inside of the...


you will have to remove all the trim from inside of the door, remove the weather seal from behind the trim as well
if it has electric windows you will have to remove the winder as a unit from inside the door
remove any broken glass from inside the door, turn the replacement glass with the narrow end down and slide it down through the top opening where the window glass normally goes in the door
once it is inside the door turn it around so it is in its normal position and place it in the channels where the glass runs, connect the electric winder mechanism and replace everything in reverse order as you removed it
hope this helps

Jul 08, 2010 | 2005 Toyota Matrix

1 Answer

How do I realign the passenger side window?


WINDOW GLASS REMOVAL

NOTE: Window glass must be operable in order to remove door assembly carrier. Any malfunction that prevents the window (manual or power) from being lowered must be corrected before proceeding.

  • Remove door trim panel.
  • Pry out sealing plugs in door assembly carrier to gain access to window glass securing bolts.
  • Lower window until window glass securing bolts are accessible.
NOTE:
If the power window motor is not working it can be renmoved to allow the window to be slid down.

  • Loosen window glass securing bolts and carefully press glass securing clamps apart.
NOTE:
If glass is being replaced due to breakage, remove door assembly carrier and remove broken shards of glass to prevent rattling noises in door.

  • Carefully lower the window regulator.
  • Lift window glass up and pivot forward, starting at the taller end of the glass. Pivot forward towards the direction of the side mirror.
  • Place removed window glass in a secure location.
WINDOW GLASS INSTALLATION

  • Slide forward part of window glass into opening and pivot glass downward, reversing the removal proceedure.
  • Raise window regulator until window glass securing bolts are visible in access holes on door assembly carrier.
  • Gently press window in the direction of the door latch or highest part of glass and tighten securing clamp bolts.
  • Remainder of installation is the reverse of disassembly.
  • Check operation of window before final installation of door trim panel.
TIGHTENING TORQUE
Window glass securing bolts...........10Nm (89in-lb)

Jun 25, 2010 | 2000 Volkswagen Beetle

5 Answers

I need to know how to replace the driver side rear window.


You dont tell us excalty the year of your CRV, so keep in mind that this is the procedure for 2000 Honda Truck CR-V 4WD 2.0L MFI DOHC 4cyl, other year is similar process. If you need take off the window, you need take off the "window regulator", so check this...


Honda CRV/Odyssey 1995-2000 Repair Information

Door Glass and Regulator

REMOVAL & INSTALLATION CRV Models and 4-Cylinder Odyssey Models
(see Figures 1, 2, 3 and 4 )


0d90b2a.jpg
Fig. 1: Always matchmark any fasteners that are mounted through a slotted hole. This bolt is used to adjust the window position

e3eb553.jpg

Fig. 2: The window is raised just enough to access the mounting bolts

5abd45a.jpg

Fig. 3: Once the window fasteners are loosened, the window can be tilted and lifted out of the door

001509f.jpg

Fig. 4: Slide the window motor/regulator assembly out of the door
  1. Remove the door panel, as outlined in this section.
  2. Remove the plastic vapor barrier.
  3. On 4-cylinder Odyssey models rear door glass, remove the center rear channel bolt and remove the channel.
  4. Carefully raise the door glass until the bolts are visible.
  5. On 4-cylinder Odyssey models rear door glass perform the following:
    1. Remove the self-tapping screws from the outer triangular trim cover and remove the cover.
    2. Remove the door glass bolts.
    3. Carefully lower the glass, then remove the bolts and nut from the rear lower guide channel.
    4. Remove the glass from the rear guide channel.
    5. Apply protective tape around the painted surfaces of the window sash trim.
    6. Tilt the window forward and remove from the window slot.
  6. Loosen the bolts, then slide the lower guide forward and remove the window from the guide.
  7. Carefully pull the glass out through the window slot. Take care to not drop the glass.
  8. To remove the regulator, perform the following:
    1. Scribe a line around the rear roller guide bolt to mark its original position.
    2. Disconnect the electrical connector and harness clip, then remove the regulator mounting bolts.
    3. Remove the regulator through the hole in the door.
  9. Installation is in reverse order of removal. Apply grease to the rollers, guides and sliding surfaces of the regulator. Make sure to install the roller guide with the rectangular hole facing rearward. Check the window operation before installing the door panel and adjust if necessary.

Hope helps.

Jun 12, 2010 | Honda CR-V Cars & Trucks

1 Answer

Side window


Hi,

Please find information about slide door window electrical glass:

http://www.construction-index.com/usa-sliding-glass-doors.asp

Thanks

May 25, 2010 | 1994 Toyota Camry

1 Answer

Power window problem. engauges then disenguages


Section 01-11: Glass, Frames and Mechanisms 1997 Windstar Workshop Manual REMOVAL AND INSTALLATION Door Glass and Regulator, Power Windows Removal
svw~us~en~file=ani_caut.gif~gen~ref.gif WARNING: IF THE REGULATOR COUNTERBALANCE SPRING MUST BE REMOVED OR REPLACED FOR ANY REASON, MAKE SURE THAT THE REGULATOR ARMS ARE IN A FIXED POSITION PRIOR TO REMOVAL TO PREVENT POSSIBLE INJURY DURING C-SPRING UNWIND.
  1. Remove front door trim panel (23942) and front door inside panel sound insulator (20394). Refer to Section 01-05 .
  1. Remove inside door belt weatherstrip.
  1. Remove front door window glass (21410) as described in this section.
  1. Remove two nut and washer assemblies attaching the window regulator equalizer arm bracket (23230).
  1. Remove four rivets retaining the front door window regulator base plate to door inner panel.
  1. Remove front door window regulator (23200) and front door window channel bracket (23288) from vehicle.
  1. Working on a bench, carefully bend tab flat to remove front door window regulator arm slides from front door window channel bracket.
  1. NOTE: Use care not to break tab; if tab is cracked or broken, replace front door window channel bracket. Make sure rubber bumper is installed properly on new front door window channel bracket, if replacement is made.

    Install new front door window regulator arm plastic guides into front door window channel bracket and bend tab back to 90 degrees.


    a9ef3ee.gif

Installation
NOTE: The front door window channel bracket and window regulator electric drive (23394) are installed into the vehicle as one assembly. The front door window channel bracket may be disassembled from the window regulator electric drive as described in Door Glass and Regulator, Power Windows .

  1. Install window regulator electric drive with preassembled front door window channel bracket into vehicle. Set the regulator base plate to door inner panel using base plate locator tab as a guide.
  1. NOTE: Two 1/4-20 x 1 inch bolts and two 1/4-20 nut and washer assemblies may be used as alternates for glass retention. However, torque must not exceed 4-7 Nm (35-44 lb-in). Equivalent metric retainers may be used.

    Install four rivets to retain front door window regulator to door inner panel.
  1. Install window regulator equalizer arm bracket.
  1. Lower front door window regulator arms to access holes in door inner panel. Install front door window glass as outlined.
  1. Install inside door belt weatherstrip.
  1. Adjust front door window glass to make sure it is properly aligned with glass run. Check window for smooth operation.
  1. Install front door trim panel and front door inside panel sound insulator. Refer to Section 01-05 .


    Door Glass and Regulator
ac1dac5.gif

Item Part Number Description 1 21410 Front Door Window Glass 2 23288 Front Door Window Channel Bracket 3 23394 Window Regulator Electric Drive 4 23230 Window Regulator Equalizer Arm Bracket 5 222A00 Front Door Glass Run Latch Side Retainer 6 N621906-S36 Nut and Washer 7 N800510-S36 Screw 8 23200 Front Door Window Regulator 9 W525172-S Rivet 10 W525175-S Rivet 11 — Wire Connector (Part of 14630 Wire Assembly) A — Tighten to 7-10 Nm (62-89 Lb-In)

Apr 13, 2009 | 1997 Ford Windstar

1 Answer

Window is off track slides down


Go to you dealer and purchase a window regulator for the side that is bad remove door panel, lock and handle remove old regulator and install new one be careful not to drop the balancing pin or remove it from the glass (very important) look at how it is assembled if pin is not in glass replace the glass the pin is made not to be removed from glass if it has been you will forever have problems until you replace the glass from dealer with pin installed

Mar 31, 2009 | 2003 Jeep Liberty

3 Answers

Hey when i push the power botton for the rear window it doesn't go down,I checked the power button,and its good ! Can i replace the power motor in the rear window,and where is it located,i would like to...


  1. Raise and support the rear door window glass to the full up position.
  2. Remove the interior door handle.
  3. Remove the rear door speaker.
  4. Remove the water shield.
  5. Disconnect the rear door window regulator motor electrical connector.
  6. Remove the rear door window regulator rivets.
  7. Remove the rear door window regulator by sliding the regulator arms off of the window glass track.
  8. Installation is the reverse of the removal procedure, noting the following:
    • Cycle the door glass to make sure of engagement of the drive mechanism.
    • Remove the rear door window glass-to-regulator bolt or rivet.
    • Position the rear door window glass as necessary to access the rear door window glass-to-regulator rivet.
    • Secure the rear door window glass in the full UP position with tape.
    • Disconnect the window regulator motor electrical connector.
    • Remove the 2 window regulator nuts.
    • Remove the 3 window regulator motor bracket nuts.
    • Install the window regulator assembly. Tighten the 3 motor bracket nuts to 89 inch lbs. (10 Nm).
    • Install the 2 window regulator nuts. Tighten the nuts to 89 inch lbs. (10 Nm).
    • Connect the window regulator motor electrical connector.
    • Remove the tape securing the rear door window glass in the full UP position.
    • Position the rear door window glass as necessary to access the rear door window glass-to-regulator rivet. Tighten the bolt to 62 inch lbs. (7 Nm), or install a new rivet.
    • Install the window regulator motor
    • Remove the window regulator assembly.
Remove the window regulator motor

Feb 23, 2009 | 2001 Ford Explorer

1 Answer

How do i install a driver window for a 95 Honda Accord EX 2 door?


if you take the channe out rubber that holds in the glass/ put the glass first in then get like glass cleaner spray in the groove sthen you slide the run channel back into the window and slide it down/ that piece should thengo into glass and hold it into the run channel. if you have any questions let me know Please rate my response thank you very much

Jan 28, 2009 | 1995 Honda Accord

Not finding what you are looking for?
1996 Dodge Grand Caravan Logo

Related Topics:

354 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...