Question about Mercury Cars & Trucks

Open Question

98 mercury mountaineer crankshaft sensor location

Location on the engine of the crankshaft sensor

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
csmock132
  • 4669 Answers

SOURCE: Where is the crankshaft position

It is stuck in bellhousing of the transmission near the rear head. The new crank sensor will come with a piece of gasket paper on the end of the sensor. Install the sensor all the way in against the pick-up wheel. When you crank the engine the wheel will rip off the paper and the adjustment will be correct.

Posted on Mar 10, 2009

Ad
emissionwiz
  • 76848 Answers

SOURCE: crankshaft position sensor location for a 98 lincoln towncar

it is on the front of the engine down low, here is a picture.
bfdacb9.jpg

Posted on May 11, 2009

  • 285 Answers

SOURCE: crankshaft sensor located 98 jeep grnd cher 4wd 6cy

it is located at the back of the engine on top of the transmission bell housing,the plug runs over to the passenger side of the engine bay and it comes out from behind the engine,you can actually get your hand on the sensor itself from under the hood on the drivers side,and i believe its a 13mm bolt holding it in,the new sensor will have a sticker on the end of it...leave it there,it is used for correct spacing between the sensor and the flywheel,hope this helps

Posted on Sep 23, 2009

Testimonial: "Everything was just like you said but as a not atleast for my jeep it is an 11mm not 13mm. Works great so far (keep fingers crossed) "

techbuster
  • 5081 Answers

SOURCE: Need to change fuel filter on 98' Mercury

The fuel filter will be located under the driver side door tucked inside the frame rail. The filter should have 2 or 3 plastic clips you can pinch the end of the clips together and pull the clips right out.

I suggest replacing the clips because they get brittle and break easy. after you remove the clips you pull the fuel lines off. there will be pressure on these lines you can release the pressure by pushing the fuel valve stem located on your fuel injection rails underneath the hood either way you will have gas all over so dont do it while your engine is hot or near any flames, sparks or anything that will ignite the gas. (If you do not release the pressure be careful not to get gas in your eyes as it will spray for a secound or two).
After you remove the lines there may be a bolt on the outside of the frame rail you have to remove to remove the filter if not it will have a clamp around it and you just loosen it and slide it out. However on some models like mine there are not any plastic clips there are metal ones on the outside that clip onto the filter and the fuel line.

With ones like this there are metal retaining clips on the inside of the line as well it will take alot of force to pull them off and you will notice how there are two or three little metal pieces sticking out of the line, with a small screwdriver try to bend them back in if you cannot you will have to buy new ones from a autoparts store (orliley autoparts or advanced auto parts have them, the dorman part number is 800-017), they are called retaining clips, without them the lines will leak like crazy and you will not be able to drive, if you give up the new lines are available at the dealer for about 100 apiece and are about 6 hours of dealer labor to put in, so be carefull

Posted on Oct 07, 2009

techbuster
  • 5081 Answers

SOURCE: location of crankshaft sensor on a 98 chevy s10

It is located on the passenger side of the engine block just under the ignition module you can see it from underside. The easiest way to see it and access it is to jack up the passenger side front wheel and take the wheel off there is a rubber flap in the wheel well you can push out of your way. I am warning you be very careful removing it mostly made of plastic I broke one off leaving most of the sensor in the engine block had to drill the rest of it out which was no fun not alot of room for you to work. Get yourself a bottle of PB Blaster and keep spraying it as your pulling out before you try pulling out the sensor try to get it free enough that you can spin it around. Hope this helps good luck it fits pretty tight!

Posted on Oct 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Location of crank sensor 05 mercury montego


Ford/Mercury are usually located by the harmonic balancer.

May 01, 2016 | Mercury Cars & Trucks

1 Answer

Where is crankshaft pisition sensor for 1995 mercury villager


1995 Mercury Truck Villager Van 3.0L EFI SOHC 6cyl

The Crankshaft Position Sensor is located: Under hood, passenger side, lower engine area, front of crankshaft pulley, mounted in engine block.

Jul 22, 2015 | Mercury Cars & Trucks

1 Answer

Where is fuel rail pressure sensor high input located on a mercury mountaineer


If you are talking about a trouble code for the pressure sensor, the sensor may be telling the computer the fuel pressure is too high. The sensor is mounted in the fuel rail on the engine.

Aug 25, 2014 | 2004 Mercury Mountaineer

1 Answer

I have a 1999 4.0L Mercury Mountaineer with a engine code P0340


Well code 340 is for a problem with the cam sensor for bank one which is the side with cylinder number one. The sensor and circuit would need to be checked which may require the use of a scanner.

Jan 31, 2014 | 1999 Jeep Grand Cherokee

1 Answer

Looking for location of crankshaft position sensor on 2000 mercury villager with 3.3l engine. parts store says there are 2 per vehicle. found one at front of engine. any idea where the 2nd one would be?


The 3.3/3.8L crankshaft sensor is located on the rear of the transmission housing, above the differential housing The bottom of the sensor is positioned next to the drive plate. Remove the 10mm bolt holding the sensor in place and remove the sensor. Install the new crankshaft sensor.
Install crankshaft sensor bolt and tighten. Connect wiring. merry christmas !!

Dec 25, 2010 | 2000 Mercury Villager

1 Answer

Where is the crankshaft position sensor


The CPS is bolted on the front of the engine, usually to the left(as you are looking at it), and just above the crankshaft pulley. Let me know if you need anything else.

Aug 08, 2010 | 2004 Mercury Mountaineer

1 Answer

I could not find the speed sensor location on my 98 mercury mountaineer. Where is it?


The Output Shaft Speed Sensor is located at the lefthand, (sitting in the driver's seat) rear of the transmission.

Jul 18, 2009 | 1998 Mercury Mountaineer

1 Answer

What side is cylider #2 on a 2002 mercury mountaineer


cylinder #2 is located on the passenger side of the engine, the O2 is in the exhaust pipe in front of the cat converter.

Dec 14, 2008 | 2002 Mercury Mountaineer

1 Answer

Locating crankshaft sensor


go to autozone.com and enter vehicle and engine info. then click on location and follow . you should find it.

Nov 26, 2008 | 1995 Mercury Cougar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

160 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

fordexpert

Level 3 Expert

5546 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...