Question about Mercury Cougar

Open Question

What is the location of the bank 2 sensor 1 for a 1999 mercury cougar 2.5 duratec v6

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: water pump location on the 2.5L V6 engine 1999 cougar

It is located on top of the engine under the throttle body, it sucks, plan on a whole day if you are a good machanic.

Posted on Dec 31, 2008

chuck943
  • 783 Answers

SOURCE: vehicle speed sensor

You will have to get to it probably from under the car it will be located just to the right of the driver's side axle

Posted on Feb 01, 2009

STEVIE_N_24
  • 147 Answers

SOURCE: o2 sensors on a 99 mercury cougar v6

Should be 4. One in front of the catalytic converter and one after on both front and rear exhaust.

Posted on Mar 30, 2009

  • 1 Answer

SOURCE: o2 sensors on a 99 mercury cougar v6

I just got done replacing the O2 sensors in my 99 Cougar due to throwing a P0135 malfunction code. There's 3. Facing the engine there's one in the front coming off of the front header, which is easy to get to. Another more tricky one if between the engine and the fire wall on the rear header pipe. The third is under the vehicle behind the transmission pan on top of the exhaust. In order to replace the O2 sensor near the fire wall you will need to remove the 4 retaining bolts for the ECM module and move it out of the way. Additionally you will need to remove the 2 retaining nuts for a wiring harness that is seated below the ECM module. Pay close attention to the connectors because the front and under vehicle O2 sensors have round connectors the one near the firewall has a squared connector. I was able to replace all 3 by myself in approximately 35 minutes. If your throwing a O2 heater malfunction code it is most likely going to be the sensor near the firewall. make sure that you know someone with a code reader so the code can be cleared. If you're do for an emmissions inspection be sure to put at least 40 miles on the new O2 sensor with different types of driving (e.g. highway, coasting, decellerated turns and rapid acceleration). Gotta love project cars for your kids!!

Posted on Apr 04, 2009

  • 55 Answers

SOURCE: location of bank 1 sensor 1 o2 sensor

Should be in the manifold on the back side closest to the firewall.

Posted on May 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the reset button to the fuel pump on a 2002 mercury cougar v6 duratec 2.5 L V6 24 valve dohc located at?


The fuel pump shut-off switch is located in the driver's foot well, behind the kick panel. Thereset button for the fuel pump shut-off switch is accessible through an opening in the kick panel.
Reset the fuel pump shut-off switch by pushing in on the reset button.

http://www.fordservicecontent.com/Ford_Content/catalog/owner_guides/02cgrog2e.pdf

Page 136

May 04, 2014 | 2002 Mercury Cougar

1 Answer

Are there torque specs for the transmission pan on a 1993 mercury cougar 3.8 v6


I'm sure that there are torque specs. for this. I just did both pans on my 1999 Mercury Sable with a 3.0 Duratec V6 DOHC with the AX4N transmission and both pans on that are tightened to 7-9 ft.-lbs.
I don't know if this would be the same unless it has an AX4N transmission. I hope this helps.
Good Luck!!!

Aug 01, 2013 | Cars & Trucks

1 Answer

My2000 mercury cougar has code 156&161 what could be the problem


error codes p0156 (02 sensor circuit malfunction) ( bank 2 sensor 2) &
p0161 (02 sensor heater circuit) (bank 2 sensor 2 ) are related. The faulty heater in the sensor will cause the PO156 to set as well. Bank 2 sensor 2
will be located on the drivers side after the converter.

Jul 11, 2012 | 1999 Mercury Villager

1 Answer

Does my 2003 mercury Sable LS wagon with duratec 3.0 liter v6 24v DOHC engine have two or four oxygen sensors? Getting lean codes for banks 1 and 2. Whistling noise under hood near air intake and engine...


Your vehicle has four oxygen sensors. There is a vacuum line underneath the throttle body that regularly fails, causing the lean condition, and the whistling and surging. Very dificult to see, but with the engine running usually you can fine the vacuum leak with your fingers. Hose is non-reinforced rubber, and is shaped in a 90 degree bend. If memory serves me right, it is the pcv hose. Replace this and your problems will cease.

Aug 19, 2011 | Mercury Sable Cars & Trucks

1 Answer

Where is the upstream oxygen sensor located on a 2001 mercury cougar 2.5 v6


Hi, the upstream sensors are at the base of the exhaust manifolds. Bank 1 is in back by the firewall. Bank 2 is in front by the radiator (#7 in picture below).
jturcotte_754.gif

Jan 06, 2011 | 2001 Mercury Cougar

1 Answer

What is the best order to use for replacing a water pump belt on a 2000 Mercury Cougar 2.5 litre?


First remove the black engine cover that says 2.5 V6 Duratec 24 Valve etc, by removing 3 bolts. Then you can see the water pum, pulley and tensioner at the rear side of the engine (opposite to the battery). Just push the tensioner with hand or flathead screwdriver and take the belt off and put the new belt the same way.

Dec 23, 2010 | 2000 Mercury Cougar

1 Answer

1998 mercury sable wagon with the V6 Duratec engine getting a P1131 reading what is it


its running lean on bank 1, eitehr a vacuum leak, or an o2 sensor.

http://www.denlorstools.com/autoblog/2009/07/ford-p1131-p1151-fault-codes-30-dohc-o-2-diagnostics/

Sep 03, 2010 | 1998 Mercury Sable

1 Answer

97 Mercury cougar xr7 v6. po443, po430, po171, po174,


Sounds like you have low fuel supply or a leak in intake system causing lean codes, check fuek pressure and volume first. Cat converter effeciancy could be caused by the lean codes, purge system sounds like solenoid failure, check for high resistance accross purge vent solenoid.

Mar 08, 2010 | 1997 Mercury Cougar XR7

1 Answer

Duratec 2.6l v6 24v where is the water pump


its located on rear of eng graphic.aspx?mod=reptiff&module_id=1&session_id=%7b906c66f6-b52e-49f8-bb1d-dc1675616fc4%7d&image_guid=00171208&print_bw=0&ine, it take 1.5 hrs.

Dec 02, 2009 | 1999 Mercury Cougar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

245 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

fordexpert

Level 3 Expert

5495 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...