Question about 2006 Toyota Sienna

Open Question

How to remove interior door panel on toyota sienna sliding door

Passenger side door panel to re-connect factory wiring from Braun ramp conversion

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1861 Answers

SOURCE: The sliding door handles of my 1998 Toyota Sienna have both broken.

OK, here you go:

Pry out on the bottom of the cupholder bottom, relieve 2 clips, pull the bottom out & slide it down

Remove the door trim screw, and pry out on the door panel, relieve 10 clips, pull door trim off

Remove the horizontal upper trim cover at the top of the door; relieve 4 clips

Remove the vertical door trim cover; relieve 2 clips

Remove the window garnish around the handle; pull the small trim cover off; remove 3 screws
This exposes the inside handle

The inside handle is retained by 2 screws.

Posted on Sep 27, 2008

bunnydawg
  • 5158 Answers

SOURCE: 2004 Toyota Sienna LE sliding door failed after battery jumpstart

could very well be the relay for the power door and possibly the interior light relay... they are located in the fuse panel under the dash.

Robert

Posted on Jan 23, 2009

  • 1 Answer

SOURCE: The sliding door handles of my 1998 Toyota Sienna have both broken.

I replaced both of my sliding door handles this weekend. It was actually pretty easy. Cheapest I could find the handles was a little over $70 each. The interior panel is held on with one screw and 10 nylon clips. The one screw is in the cup holder. Put you hand in the cup holder and push out at the bottom. It pops right off exposing the one screw. I started on the clips from the top at a corner. Seemed to be the easiest place to slide a screw driver under. Once I got the screw driver in, I started working my fingers under the panel. The clips run mostly along the top and bottom about 6 inches from the edge. I made an effort to apply the force as close to the clips as I could to reduce flexing the panel. Once I got the first clip to pop out the other followed pretty easy and the panel lifted right off. Carefully peel back the plastic barrier. The exterior handle is held on with two 10mm bolts. Connecting the short cable was pretty obvious once you could see everything. Now I have to teach everyone to open the side doors very gently! Hope this helps.

Posted on Mar 09, 2009

  • 2 Answers

SOURCE: removing door panel in 2000 toyota corolla

remove phillips scew and the door handle. remove padded arm rest on the door by lifting it up, and remove 2 screws. You can use a panel tool to remove the plastic toggle like pins holding the panel border in. Be as gentle as possible they may break due to becoming brittle.

Posted on Apr 06, 2009

  • 4 Answers

SOURCE: 2005 Toyota Sienna XLE - Automatic sliding door not closing.

This may or may not work depending on exactly what is wrong with the door, I cant tell what is wrong without looking at it directly however:
You can try starting with all doors closed and unlocked, keys in hand disconnecting the battery and letting the vehicle sit for 2 min or so, then reconnect the battery. Put the key into the ignition and turn it to the on position but do not start the van. Next press the button to disable the power sliding door for the drivers side, then manually open the door fully, wait 5 seconds, then close it manually fully. Press button the button again to re-enable the power sliding door, then try to use it with the automatic feature either by pulling the handle or using your remote, this may or may not work depending on if the door has somehow become de-initialized (it should work now) however if something is broken inside the door closing mechanism or door closed/open sensors, the door will continue to malfunction.

Posted on Aug 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front Passenger door lock stuck


Hi Andrew:
Many local tow truck operators know how the latches work and use a tool called a slim jim to trip the latch.

If you really want to give it a go yourself, I'd remove the interior panel on the drivers door so that I could see exactly how the mechanism worked. Using that knowledge, you'll have to practice using a skinny tool, wire, whatever works, to unlatch the drivers door.

Once you've got it figured out, apply the mirror image of that process to the passenger door.

When you achieve success, you will be well on the way to becoming a tow truck driver. (or a car thief)

Happy Happy!

Jun 22, 2015 | 1999 Toyota Sienna

1 Answer

02 Toyota Sienna power sliding door not working


See if power reaches the motor. If it does and motor does not operate you have found the problem. If no power then the issue is electrical in nature and you will have to trace the current flow to the motor.

Apr 11, 2017 | Cars & Trucks

2 Answers

Our passenger side power sliding door doesn't open


Check out the wiring. Sounds like something is loose or the switch may be going bad.

Mar 10, 2010 | 2004 Toyota Sienna

1 Answer

1999 Toyota Sienna Drivers Side Sliding door hard to open from the outside only - OK using inside latch. (think maybe cable attached to inside latch is "stretched". What's involved in removing interior...


well they dont use cables they use a iron rod so just snap off the pannel the snaps are in the out side of the door then just remove the arm rest and the panel comes right off remove the dirt cover then just tighen it and it will work again

Nov 06, 2009 | 2001 Toyota Sienna

1 Answer

Both manual sliding doors on my Toyota Sienna will not open


If you can remove the inner door panel you will see a maze of cables running to the various locking points on the sliding door. If the cable going to the FRONT latch on the sliding door is broken (or in my case, simply dislodged inside the door) the door acts as if it is frozen shut.

The front cable is short, and easily replaced even by a newbie mechanic.

May 27, 2009 | 2004 Toyota Sienna

1 Answer

2004 Toyota Sienna LE sliding door failed after battery jumpstart


could very well be the relay for the power door and possibly the interior light relay... they are located in the fuse panel under the dash.

Robert

Jan 23, 2009 | 2004 Toyota Sienna

3 Answers

The sliding door handles of my 1998 Toyota Sienna have both broken.


I replaced both of my sliding door handles this weekend. It was actually pretty easy. Cheapest I could find the handles was a little over $70 each. The interior panel is held on with one screw and 10 nylon clips. The one screw is in the cup holder. Put you hand in the cup holder and push out at the bottom. It pops right off exposing the one screw. I started on the clips from the top at a corner. Seemed to be the easiest place to slide a screw driver under. Once I got the screw driver in, I started working my fingers under the panel. The clips run mostly along the top and bottom about 6 inches from the edge. I made an effort to apply the force as close to the clips as I could to reduce flexing the panel. Once I got the first clip to pop out the other followed pretty easy and the panel lifted right off. Carefully peel back the plastic barrier. The exterior handle is held on with two 10mm bolts. Connecting the short cable was pretty obvious once you could see everything. Now I have to teach everyone to open the side doors very gently! Hope this helps.

Sep 21, 2008 | 1998 Toyota Sienna

3 Answers

Replacing RH Side view mirror on a 2006 Toyota Sienna


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Jul 29, 2008 | 2006 Toyota Sienna

Not finding what you are looking for?
2006 Toyota Sienna Logo

Related Topics:

1,733 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...