Question about 1993 Saturn SC2

Open Question

Trs,trs2,trs3,trs4,tcc,trs lp fuse ,not getting current

No current going through fuses in fuse block

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

MrScary66613
  • 1990 Answers

SOURCE: 1998 saturn sl2 1.9 dohc

TRS LP
TRS 3/4
TRS 2/TCC
These are the fuses for the solenoids in the valve body Inside the Transmission, they turn on & off as needed to shift.
Check all of those fuses, making sure they are not corroded or tarnished.
Make sure that your charging system is functioning properly.

Please Rate My Response! Thanks!

Posted on Feb 02, 2009

  • 4 Answers

SOURCE: no spark, no power to

Make sure the key is in the run pos. when checkin the trs3/4 fuse. More than likely that fuse is blown u will have a no spark condition. Check that b4 u condem the icm or crank sensor

Posted on Jul 16, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the location to replace overhead lights fuse in 2003 oldsmobile aurora


Rear fuse box. INT LP 10 amp . there is also INT LP relay in the same rear fuse box .
Fuse Block - Rear
Under the rear seat, on the left side of the floor pan
The INT LP fuse in the fuse block - rear supplies battery positive voltage to the normally open switch contacts of the INT LP relay. The INT LP fuse also supplies battery positive voltage to the INT LP relay control circuit. The fuse block - rear also supplies battery positive voltage to the relay control circuit for the front courtesy lamp. The door modules communicate on a simple bus interface (SBI). When you open any door, the switch contacts of the door open switch close. When a door open signal circuit is grounded, that door module sends a message to the drivers door module (DDM) in order to indicate that a door is open. The DDM sends a class 2 message to the rear integration module (RIM) in order to indicate which door is open. The RIM activates the INT LP relay in order to provide battery positive voltage to the interior courtesy lamps. When any front door is opened, the RIM will energize the FRT CTSY lamp relay grounding the I/Pcourtsey lamps at G302. Depending on which doors are opened, front or rear, the proper interior courtesy lamps illuminate. The RIM provides a pulse width modulated ground to all interior courtesy lamps for the interior lights theater dimming feature. Some of the courtesy lamps are also used as reading lamps, each reading lamp may be manually turned on or off using it's own respective switch

Sep 24, 2015 | Oldsmobile Cars & Trucks

1 Answer

Where is the location of 06 Saturn Ion 2 compressor relay?


Connector 1:
Fuse Block - Underhood Label (2.2L, 2.4L)
Connector 2:
Fuse Block - Underhood Top View (2.2L, 2.4L)
Connector 3:
Fuse Block - Underhood Bottom View (2.2L, 2.4L)
Connector 4:
Fuse Block - Underhood C1 (2.2L, 2.4L)
Connector 5:
Fuse Block - Underhood C2 (2.2L, 2.4L)
Connector 6:
Fuse Block - Underhood C3 (2.2L, 2.4L)
Connector 7:
Fuse Block - Underhood Label (2.0L)
Connector 8:
Fuse Block - Underhood Top View (2.0L)
Connector 9:
Fuse Block - Underhood Bottom View (2.0L)
Connector 10:
Fuse Block - Underhood C1 (2.0L)
Connector 11:
Fuse Block - Underhood C2 (2.0L)
Connector 12:
Fuse Block - Underhood C3 (2.0L)
Connector 13:
Body Control Module (BCM) Label
Connector 14:
Body Control Module (BCM) Top View
Connector 15:
Body Control Module (BCM) Bottom View
Connector 16:
Body Control Module (BCM) C1
Connector 17:
Body Control Module (BCM) C2
Connector 18:
Body Control Module (BCM) C3
Connector 19:
Body Control Module (BCM) C4
Connector 20:
Body Control Module (BCM) C5 (UE1)
Fuse Block - Underhood Label (2.2L, 2.4L)
2.2L

alt="Object Number: 1438995 Size: MF">

alt="Click here for detailed picture of above image.">

2.4L

alt="Object Number: 1583009 Size: MF">

alt="Click here for detailed picture of above image.">

Fuse Block - Underhood Label Usage (2.2L, 2.4L)
No.

Device

Rating

Description
1

ECM (2.4L)/TCM Fuse
10A

ECM (2.4L)/TCM
2-3

--
--

Not Used
4

RH HDLP Fuse
15A

Headlamp - Right
5

A/C Fuse
10A

A/C CLUTCH Relay
6-7

--
--

Not Used
8

ABS Fuse
10A

EBCM (JM4)
9

ECM/ETC Fuse
15A

ECM
10

EMISS Fuse
15A

EVAP Canister Purge Solenoid, Coolant Level Switch, MAF Sensor, HO2S 1, and HO2S 2
11
IGN Fuse
10A
ICM and PNP Switch (A/T)
12
--
--
Not Used
13
TRANS2 Fuse
10A
ECM, Automatic Transmission
14
TRANS1 Fuse
10A
TCM (MN5)
15
BACK UP Fuse
10A
PNP Switch (A/T) or Backup Lamp Switch (M/T)
16
INJECTORS Fuse
10A
Fuel Injectors 1-4
17
FOG LP Fuse
10A
FOG LAMP Relay (T37)
FOG LP Fuse
15A
FOG LAMP Relay (T96)
18
LH HDLP Fuse
15A
Headlamp - Left
19
WIPER Fuse
25A
WIPER 1 Relay
20
HORN Fuse
10A
HORN Relay
21
RADIO Fuse
20A
Audio Amplifier (UZ6)
22
ABS Fuse
20A
EBCM (JM4)
23
RR DEFOG Fuse
30A
REAR DEFOG Relay
24
A/C CLUTCH Relay
--
A/C Compressor Clutch

Jul 17, 2015 | 2006 Saturn ION 2

1 Answer

Why wont the headights or running lights work on my 2002 Buick LaSabre?


There are several reasons why your headlamps an running lights don't work , the headlamp switch is a good one ,plus relays an the DIM - dash integrated module an associated wiring ! Here is how the headlamps work , right out of Buick factory service info !
The dash integration module (DIM) provides battery positive voltage to the signal circuits of the headlamp switch. The signal circuits include the headlamp switch headlamps on signal, the flash to pass switch signal and the high beam input. With the headlamp switch in the ON position, a ground path is available for the headlamp switch headlamps on signal circuit of the DIM through the headlamp switch. The DIM provides ground to either the headlamps high beam relay control circuit or the headlamps low beam relay control circuit of the low beam circuit. The position of the headlamp dimmer switch determines which relay control circuit has ground. The DIM supplies battery positive voltage to the relay control circuits, if the headlamps are necessary. The fuse block - underhood supplies battery positive voltage to both relay switch circuits. When the low beam relay control circuit is energized, current flow is to both low beam fuses and to the low beam headlamps. The headlamps have ground at G103 and at G401. When the headlamp high beam relay control circuit is energized, current flow is to both high beam fuses and to the high beam headlamps. The high beam circuit is divided into a left and right side circuit. The current flow of the left high beam is from the fuse to the left high beam lamp. From the lamp, the current flows to the normally-closed contact of the DRL relay to G103. The current flow of the right high beam is from the fuse to the right high beam lamp. From the lamp, the current flow is to ground at G401. When the headlamp dimmer switch lever is pulled toward the driver, the flash-to-pass switch closes. This grounds the DIM flash to pass switch signal circuit. In response to this input, the DIM energizes the HDLP HI BM relay. Both high beams remain on until the driver releases the switch handle. If the low beam headlamps were on during a flash to pass operation, the low beams remain on. The headlights may be switched to high beam with the opposite movement of the headlamp dimmer switch lever.
By running lights , do you mean park lamps or day time running lamps ?
Park, Tail, License and Marker Lamps
The park lamps, including the license lamps, are turned on when the headlamp switch is placed in the PARK or ON position or anytime the headlights are requested. The fuse block - rear supplies battery positive voltage to the switch contacts of the Park LP relay. When the headlamp switch is in PARK or in ON, the park lamp switch on signal circuit of the DIM has a ground path. The DIM provides battery positive voltage to the control circuit of the Park LP relay. When the park lamps and/or the tail lamps are ON, the DIM energizes the park lamp relay control circuit. This closes the switch contacts. Current flows from the Park LP relay to the LH PARK LP and the RH PARK LP fuses. From the fuse, the current flows to the park lamps. The left park lamps are grounded at G103, G401 and G402. The right park lamps and the right tail lamps are grounded at G103 and G401. The DIMR fuse supplies battery positive voltage to the license lamps and to the DIM instrument panel lamp fuse supply voltage - 1 circuit, for interior lamps dimming. The license lamps are grounded at G401.
The best advice I can give is that you take this to a ASE certified professional repair facility unless your a qualified automotive electric repair person !
Diagnostic Starting Point - Lighting Systems
Begin the system diagnosis with the Diagnostic System Check - Lighting Systems . The Diagnostic System Check will provide the following information:
?€¢
The identification of the control modules which command the system


?€¢
The ability of the control modules to communicate through the serial data circuit


?€¢
The identification of any stored diagnostic trouble codes (DTCs) and their status

The use of the Diagnostic System Check will identify the correct procedure for diagnosing the system and where the procedure is located.

The

Mar 15, 2015 | 2002 Buick LeSabre

1 Answer

Where is the fuse for the sunroof on a 2002 Tahoe?


Ignition power comes from the 25A PWR WDO circuit breaker in the right I/P fuse block. The 15A CTSY LP FUSE in the underhood fuse block is the source of battery power.

Aug 18, 2014 | 2002 Chevrolet Tahoe

1 Answer

Which fuse is for the panel lights


With the headlight switch in the PARK or HEAD position, power from the 20A LP PARK FUSE in the underhood fuse block is applied through the 15A TAIL LIC LAMPS FUSE and the 7.5A PANEL DIMMING FUSE in the I/P fuse block.

May 20, 2014 | 1999 Buick Regal

1 Answer

I have a 2001 Saturn SL. The check engine light keeps coming on. It stalls when trying to take off. So far, I have replaced EGR valve, Temp sensor, spark plugs, oxygen sensor, fresh air EGR valve flow. It...


That fuse powers shift soledoid 2 and the TCC solenoid. One of those 2 solenoids is probably shorted. The transmission will have to be repaired.

Jul 17, 2017 | 2001 Saturn SL

1 Answer

Drivers side window probably need fuse change. Need diagram to show fuse for window in 1995 grand prix


Check this diagram location...

zjlimited_946.jpg

POSITION 10
IGN SW2 -- I/P Fuse Block PWR WDO and Circuit Breaker "D'; Passenger Side Underhood Electrical Center: TCC and ENG EMIS Fuses

Hope helps.

Mar 29, 2011 | 1995 Pontiac Grand Prix

1 Answer

No spark, no power to three fuses...trs lp,trs 3/4,trs 2/tcc. I'm not sure what circut the fuses are for.c


Make sure the key is in the run pos. when checkin the trs3/4 fuse. More than likely that fuse is blown u will have a no spark condition. Check that b4 u condem the icm or crank sensor

Nov 01, 2010 | 1999 Saturn SL

1 Answer

I have a code 741 on my 01 saturn S- series any suggestion on how to fix.


check the tcc fuse under the hood mfuse block if thats good,,,its most likely the tcc solenoid inside the ntop of the trans,the dealer has a test they can do to see ifits working,if its not the tcc solenoid which im sure it is,its either a wire issue or a pcm,i would go for the tcc solenoid

Oct 12, 2009 | 2002 Saturn Sl

1 Answer

1998 saturn sl2 1.9 dohc


TRS LP
TRS 3/4
TRS 2/TCC
These are the fuses for the solenoids in the valve body Inside the Transmission, they turn on & off as needed to shift.
Check all of those fuses, making sure they are not corroded or tarnished.
Make sure that your charging system is functioning properly.

Please Rate My Response! Thanks!

Feb 02, 2009 | 1998 Saturn SL

Not finding what you are looking for?
1993 Saturn SC2 Logo

Related Topics:

280 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...