Question about 2007 Hyundai Santa Fe Limited

Open Question

Cant find the etacs module for my 2007 hyundai santa fe

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 566 Answers

SOURCE: 2007 Hyundai Santa Fe - Replacing fog light

hi have not had pleasure of this on santa fe yet? but will try to help dependant of which side o/s or n/s ? i would first remove the screws holding the front of the under engine plastic cover/shield and drop down sufficient to gain view/access? to the rear of fog lamp then if a cover is on? try turning anti clock to remove? or if rubber cover pull off? then the bulb and clip should be visible? unplug the wire from bulb then the spring clip holding bulb in place normally just sring the 2x top ends together and swing down/clear to remove bulb? refit new bulb correctly! pay attention to position old bulb positioned? then clip securely and re connect wire at this stage it would be best to ensure bulb works ?? before you re assemble all else? wish you luck and hope this helps with your problem ?

Posted on Oct 28, 2008

Ad
goalie39
  • 469 Answers

SOURCE: ''check engine light'' illuminated, 1004 Hyundai, Santa Fe

If you live in the US, take it to qany Auto Zone store and thy will read the codes off for you, I would suspect any right thinking competitor would do the same, check if you don't have one near by.

Hope this is of some help.
Ed

Posted on Apr 21, 2009

emissionwiz
  • 76649 Answers

SOURCE: PROGRAM KEYFOB FOR HYUNDAI SANTA FE

This is from the factory service manual of your car:
There is no onboard programming procedure for this vehicle. This vehicle requires special equipment be connected to the vehicle to program the keyless remote. Translation you need the dealer to do this.

Posted on May 22, 2009

jmgldsmth
  • 1889 Answers

SOURCE: 2007 Hyundai Santa Fe Headlight

you need a torx screwdriver

Posted on May 29, 2009

michigan man
  • 3533 Answers

SOURCE: how to change blower motor in a 2003 hyundai santa fe

try these two websites www.alldatadiy.com and www.autozone.com and you should be able to get pictures and diagrams showing you how to repair your truck

Posted on Aug 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sunroof on 2007 Hyundai Santa Fe only opens/closes whenever it feels like it. It's been less frequently that it cooperates. Checked fuse. It's good (changed it just to make sure) not the motor. Help!


If the 10A ETACS FUSE in the passenger compartment junction block and the 15A SUNROOF FUSE in the engine compartment junction block are OK, the sunroof control module or the sunroof switch could be defective. Another possibility is a wiring defect.

Nov 18, 2016 | 2007 Hyundai Santa Fe

1 Answer

How do I change the fuel filter on a 2006/7 Hyundai Santa Fe 2.2 CRDT CDX safely?


There is no external type fuel filter on the Santa Fe. It is built into the fuel pump module in the tank,you rould have to remove your rear seat bottom cushions and get to the access plate and remove the pump module. Can be very time consuming if you have never done this before.

Oct 20, 2011 | 2007 Hyundai Santa Fe Limited

1 Answer

Hello. Where is that ETACS box located under the dash on a 2001 hyundai santa fe? I have the fuse box panel off but cannot find the etacs box to sitch to off for remote programming.


I live in Australia so mine is a right-hand-drive Santa Fe 2001. I wonder if this is why so many people seem to have so much trouble locating this box. On a left-hand-drive the box may be more over the footwell instead of near the side wall. In my car it is actually behind the fuse box near the right-hand side-wall. The switch is actually not visible as it is located on the right hand side of the ETACS box (near the side-wall). I had to locate it by feel. Once thought I had located the switch I held my finger pressed up against it for a while, to litterally get an imprint of the switch. The position towards the driver appears to be the "off" position, and the position towards the front of the car the "set" position. I turned the ignition key on (2 clicks), flicked the switch to the "set" position, pressed the lock button (I watched the flash on the remote, but heard nothing from the car), turned the ignition key to "off" and pressed the remote lock button again, then reset the switch on the ETACS box back to it's original position. That's it. My remote is working now. Hope this helps someone else...

Jan 30, 2011 | 2001 Hyundai Santa Fe

1 Answer

Where is the ETACS unit on my 2007 Santa Fe?


Go to www.hmaservice.com and register( Vehicle by VIN). Afterward, you have access to shop manuals, service bulletins, wiring diagrams, etc. about your vehicle.

Sep 28, 2009 | 2004 Hyundai Santa Fe

1 Answer

Where is the ETACS unit on a 2007 Santa fe?


which one is it?... 2004 or 2007?
Go to www.hmaservice.com and register( Vehicle by VIN). Afterward, you have access to shop manuals, service bulletins, wiring diagrams, etc. about your vehicle.

Aug 22, 2009 | 2004 Hyundai Santa Fe

1 Answer

Hyundai santa fe 2002 remote key fob locking ok but fails to unlock. suspect micro switch faulty. can it be replaced?


Do the doors lock normally when using the manual switch on the dirver's door panel? If so, the problem is in the ETACS module. Here's the wiring diagram:

5f27f1c.jpg

May 16, 2009 | 2004 Hyundai Santa Fe

1 Answer

Central locking wont stay open


Here's what I suspect is happening. The door locks will lock and unlock normally when the key is OUT of the ignition. If the key is IN the ignition, the doors cannot be locked (manually, key fob, or otherwise, if the system is operating as designed - prevents the doors being locked when the key is in the ignition). I've seen this problem before, but on a Santa Fe, not an Accent. The ground signal of the right hand front passenger door was lost, and the doors automatically locked. Perhaps something similar is happening in the circuit between the ETACS module and the right front passenger door lock/unlock actuator. Could be anywhere in the circuit.



d05b136.gif
ab4c712.gif These wiring diagrams may be helpful. The relays expecially may help solve this issue. As you can see, these relays are also controled by the ETACS module (Remote Keyless Entry).

67dc553.gif

Mar 31, 2009 | 2003 Hyundai Accent

1 Answer

How to program keyless remote


I just had to buy one too and these are the instructions I was given by the guy I bought it from. I haven't tried them yet. Hopefully they work for us both :).

1.Find the ETACS unit under the steering wheel first,there is a small switch onit.
2.Once the switch is located make sure your key is not in the ignition and set the switch from off to set.
3.Press keyfobs door lock button for one second, this sends the codes to the ETACS and stores it.
4.Do the same thing if you have 2 remotes for the vehile.
5.Now set the ETACS switch from set to off.
6.Remotes should now be programed.

Jan 10, 2009 | 2007 Hyundai Santa Fe Limited

1 Answer

Had to buy keyless entry remote.2007 santa fe limited. What is procedure for programming


I just bought one for mine too! The guy who sold it to me gave me these directions but I haven't tried them yet! Am going to on my lunch hour! Hope they work for us both :)

Forgot to put prog. instructions.in with your fob so here they are.
1.Find the ETACS unit under the steering wheel first,there is a small switch onit.
2.Once the switch is located make sure your key is not in the ignition and set the switch from off to set.
3.Press keyfobs door lock button for one second, this sends the codes to the ETACS and stores it.
4.Do the same thing if you have 2 remotes for the vehile.
5.Now set the ETACS switch from set to off.
6.Remotes should now be programed.

Jan 10, 2009 | 2007 Hyundai Santa Fe Limited

Not finding what you are looking for?
2007 Hyundai Santa Fe Limited Logo

Related Topics:

174 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...