Question about Cars & Trucks

Open Question

How to change glow plugs on a 1.5 crdi hyundai getz

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 53 Answers

SOURCE: hyundai getz

if the speedo still works then it will need a spedo unit if the speedo doesn't work it is either the cable or the gear in the trans to check the cable unthread from trans and attach a drill to the cable innereds spin the drill if the speedo does not move replace the speedo cable

Posted on Oct 18, 2008

Ad
  • 1986 Answers

SOURCE: How do I change the 3rd brake light on a 2004

the light housing will either be clipped in and you will need to gently pry on the housing to open it, or you will be able to unscrew the housing through the trunk itself

Posted on Sep 29, 2009

  • 566 Answers

SOURCE: How to set the clock for a Hyundai Getz?

hi from uk ! to set clock/time on getz look t the speedometer ? you will see two buttons on the bottom of dial ? the left button is to cancel the trip meter by pressing button in for trip A and again for B trips the right hand button marked hr + min ? to set hour time turn to left untill hr time is shown then release now turn button to right to set the minutes then releas when time/minutes ar correct that is it! ps you cannot cancel the odometer/milage clock only trip meter hope this helps best wishes from n/west uk

Posted on Oct 16, 2009

Testimonial: "Thank you very much, your instructions were perfect :)"

  • 102 Answers

SOURCE: hyundai getz 1.1 2004 engine sluggish whenpulling

thats sounds like the most likely culprit, collapsed cat. or collapsed muffler.. not cheap to replace. but has to be done.

Posted on Nov 15, 2009

  • 1 Answer

SOURCE: CHANGING A FUEL FILTER IN A HYUNDAI GETZ

I have an '03 Hyundai Accent 1600cc. I am told by the techies at the local dealer, the fuel filter is ON the fuel tank. You gain access to it by removing the back seat, then opening the panel beneath the back seat. Replace the filter, screw the panel back onto the floor and the job is done....

Posted on Feb 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to allign hyundai getz 1.5 crdi timing belt


camshaft is 90? to the right or 3 oclock position and the crank is between the 1 oclock and the 2 oclock ,look in them positions and you should see the marks none of the others need timing

Dec 07, 2014 | Hyundai Cars & Trucks

1 Answer

How to change stop light globe on 2008 hyundai getz


Remove the two 10 mm (head) bolts that hold the stop light. This bolts are between the tail light assembly and the tail gate weatherstrip. You can see them without having to remove anything.

By using a masking tape wrapped flat screwdriver, pry "back" the whole tail light assembly. Once out, you can twist the brake light (or reverse, or turn signal) bulb plug, remove and replace the bulb.

The Getz uses standard two filament brake globes (1/4 turn to install).

May 12, 2014 | 2008 Hyundai Getz 1.6

1 Answer

I have 2005 hyundai accent crdi .it has run145000. It gives starting trouble during first start.


Check the glow plugs but it sounds like the injectors and pump needs to be serviced.

Mar 23, 2014 | Hyundai Accent Cars & Trucks

1 Answer

Torque settings on hyundai getz 1.6 Top and cam


The info is said to be available here, if the link still works. You may have to register yourself first.

http://www.hyundai-forums.com/attachments/getz-forum/57970d1353332110-help-hyundai-getz-1-6-torque-settings-getz-1.5-1.6-specs-torque-settings.pdf

Dec 20, 2013 | Cars & Trucks

1 Answer

Getz 1.5 engine light on after replacing glow plug not starting now


Check wiring on glowplugs . Check connector plate is not short-circuit on head .

Mar 18, 2013 | 2005 Hyundai Getz 1.5

1 Answer

My hyundai getz 1.5 crdi has a total electrical failure, want could be wrong?


the PCM could have went out, might have to order a new 1, or check the wiring and connections to the PCM

Jul 08, 2012 | Hyundai Santa Fe Cars & Trucks

1 Answer

How to change the spark plugs in a 2008 getz


To get too my 2008 Getz spark plugs. I used my socket set with an extension on the plug spanner provided with the inexpensive kit !

Jan 19, 2012 | 2008 Hyundai Getz 1.4

2 Answers

Hyundai tucson 2 liter crdi gear box sound its a manual transmission


Hi there, the Common Rail Diesel Inyection (CRDI) 2000 cc 112 Hp M/T have a big trouble on cluth plate, and sounds very loud between 1500 and 2000 rpm on 2,3,4 shift.That motor has too much torque and cause excesive wear in the cluth roll and plate so starts roominess in the cluth system. You could change those parts but quickly the sounds come again. Hyundai is the resposable of that damage. I hope in the near future recall the CRDI model 112 Hp and replace the cluth.

Sep 20, 2009 | 2005 Hyundai Tucson

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

438 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...