Question about 2003 Kia Sedona

Open Question

Clock spring on 2004 kia sorento - 2003 Kia Sedona

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 4 Answers

SOURCE: crankshaft sensor for 2004 kia sorento

The above information about the sensor being located at the top of the motor to the passenger side of center is bogus. That is only the pig tail plug in. The actual sensor pig tail continues down below, underneath the plastic lower timing belt cover, on the front of the motor, just above the crankshaft timing gear.

It is a very involved process of removing and replacing. You will have to remove all of the belts, the front timing belt covers, (upper and lower). You will also have to remove the front bracket that is mounted to the front of the block, which serves as the mount for the power steering pump, the alternator and the A/C compressor.You will also have to remove the crankshaft pulley. You cannot remove the plastic lower timing belt cover unless you remove all of these things first. The sensor is located underneath the lower cover. It has two bolts that hold it in place. You will have to remove these two bolts.

The crankshaft pulling bolt is a right handed thread and loosens by turning counter clockwise. The pulley will slip off but is a very tight fit. Do not try to turn it while removing it as there is a small pin that keeps it aligned to one position. Use a small ball pine hammer to tap it loose.

It is also a good idea to remove the electric cooling fan shroud that is mounted to the inside side of the radiator and the radiator hoses to give yourself more room to work. It has only two bolts at the top holding it in place. And then slips into two retaining clips at the bottom. Lifting it will pull it out of these retaining clips.

When you remove the small bypass hose located at the top of the radiator , to the passenger side, be careful not to break off the small nipple protruding out of the radiator tank. It is plastic and will break easily if you try to pull the rubber bypass hose from it. This will have to be taken to a radiator shop to have repaired if you accidentally break this off. Be sure to carefully loosen the hose from this nipple before trying to pull it off.

And one more thing, if you go to that much trouble to replace this sensor, it is a good idea to go ahead and replace the timing belt as well. It is a maintenance item and you will have to go through the same process to replace it as well. Do it once and do it all.

I hope this helps.

Posted on Nov 15, 2008

Ad
aref_bilal
  • 13 Answers

SOURCE: I am changing the spark plugs on my 2004 Kia sorento

Be careful there.. If you remove the Throttle Position Sensor TPS or the throttle Cable, the engine light will come on because there is a certain setting that needs to be done to ensure accurate emission control.

Posted on Apr 14, 2009

  • 51 Answers

SOURCE: reset check engine light in a 2004 Kia Sorento

usually you can reset a check engine light buy disconnecting the battery for about 30 minutes.

Posted on Jun 02, 2009

  • 39 Answers

SOURCE: How do you change head lights on a 2004 kia sorento?

The whole headlight assembly needs to be removed from the vehicle to access the lamps inside; especially on the side with the battery (left side).

Remove 3 10m bolts (one on top two on front)

Headlight assembly is held in place wth a large Nylon clip ear outer edge at bottom of the unit. Tilt out at the top and then pull forward and upward to remove. It fels like something's gonna break, but it's pretty tough.

Remove large round cap from behind either high or low beam lamp. Both lamps are hels in with a metal spring clip. Low beam is H-7, high beam is H-3.

To re-install, press bar into Nylon clip and then install 3 10mm bolts. Use a Torx bit to engage gear teeth and adjust height if necessary. There may or may-not be adjusters for left-right alignment.

Posted on Jun 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Firing order to 2004 kia sorento 3.5L


The firing order is given as 1-2-3-4-5-6 for distributorless ignition.
The link below gives some diagrams:

kia sorento 3 5 firing order Google Search

There's also a youtube video:
03 Kia Sedona 3 5L firing order

Mar 07, 2017 | 2004 Kia Sorento

1 Answer

Oxygen sensor connector 2004 Kia Sorento


The removal procedure of Oxygen sensor connector for 2004 Kia Sorento is explained in below link. Please refer through it.

531fa0c2-d966-466f-8ade-159cb41e391a.jpg


0ebd0374-2764-42ba-a725-ed8fe7b650c7.jpg

Jun 11, 2013 | 2004 Kia Sorento

1 Answer

2004 Kia Sorento lifter clicking in the engine


it could be a lifter or a sticky injector I would say to see your kia dealer for issues or recalls they are good about following thru with issues

Jul 06, 2012 | 2004 Kia Sorento

1 Answer

I have an '04 Kia Sorento, my clock was replaced 5 years ago because it was defective. Just recently it started blinking. I have reset the time, but its still blinks. My question is do I need to replace...


Hi,

The sorento clock, along with many other import vehicles of this era, have notorious issues with poorly designed circuit boards in the clock module. We fix these on a routine basis, check out the website, we have lots of info there and would be happy to help you out, thanks!
www.autoclockrepair.com

Oct 15, 2010 | 2004 Kia Sorento

2 Answers

Does the kia sorento 2.5 crdi xe have a timing on a 2004 plate


THE KIA SORENTO HAS 3.3 AND 3.8 ENGINES THEY HAVE TIMING CHAINS.THE KIA 2.4 ENGINES HAS TIMING BELT GUIDE PLATE.

Jun 21, 2010 | 2004 Kia Sorento

1 Answer

My cars clock


Its might be going bad you would have to replace it

Jan 25, 2010 | 2004 Kia Sorento

Not finding what you are looking for?
2003 Kia Sedona Logo

Related Topics:

210 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...