Question about 2004 Dodge Intrepid

Open Question

What's your problem?2004 dodge intrepid with code p1776

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 272 Answers

SOURCE: po700 and p1776

P0700 is EATX code present. It simply means that the engine computer has noticed that the transmission computer has a dtc in it. This causes the Pcm (engine computer) to turn the check engine light on. You will need to have the TCM (trans computer) checked for codes to know what to diagnose.

error code P1776 - Replace rear solenoid switch

Likely both related The P1776 probably kicked off the P0700 notification.

Hope that helps! Happy Motoring!

Posted on May 11, 2009

emissionwiz
  • 75822 Answers

SOURCE: I have a 2002 intrepid SXT 3.5L automatic

P0700 is an alert code the p1776 is the actual trouble code.
Code p1776 is solenoid switch valve latched in low/reverse position. Valve is located in valve body not solenoid body reploace it

Posted on Jul 17, 2009

bestdarngood
  • 3037 Answers

SOURCE: I have a 2002 intrepid SXT 3.5L automatic

The p0700 means that there is a code in the trans controller. This code would then be the p1776. When the code was set the trans went into what they call "limp in mode". This is a safety feature that allows the vehicle to still driven in second gear so to make it to a repair shop or off the road.

P1776 is solenoid switch valve is latched in low/reverse. The most likely cause is the electrical portion of the trans which is called the solenoid pack. In order to replace this you need to remove the valve body inside the trans because it is bolted to the top side of it. I recommend making sure when the trans pan is dropped that there is no debris in the pan. If debris is found that the unit may need to be removed, torn down, and inspected to make sure there is no other problems.


Benjamin

Posted on Jul 17, 2009

  • 608 Answers

SOURCE: My 2004 dodge intrepid is overheating how to git

Remove the top hose, unbolt the thermostat housing, remove old themostat and install new unit with new gasket. Replace top hose and fill with coolant. Be sure to re-check the coolant level after start up, beore you drive it anywhere, to eliminate any air pockets in the coolant.

Posted on Mar 22, 2010

Testimonial: "Thanks for the information it did help"

jgregory412
  • 1 Answer

SOURCE: WHAT IS CODE P0700 FOR A 2004 DODGE INTREPID

P 0700 is basically a "generic" code signifying that the Transmission Control Module has detected a fault somewhere within the transmission's electrical system (typically a shift solenoid malfunction). If you see P 0700, take your car to some place that can plug a scan tool into it and retrieve the other codes which are causing your car to display the P 0700 code.

Posted on Sep 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine Code P1776


Generally speaking, the code for Dodge involves the low-reverse solenoid in the transmission. It may be stuck or defective.

Sep 10, 2012 | 2002 Dodge Intrepid

1 Answer

What is causing my car to say transsmisson control problem


P0700 Transmission P01776 Ignition ****** request. P0870 Transmission fluid pressure sensor C. Your main concern is the valve body assembly this will take care of P1776. And as for the P0870 you will need the solenoid pack also. Before you decide to attempt this try a relfash of the TCM(transmission control module)

Feb 23, 2012 | 2002 Dodge Intrepid

1 Answer

The problem when you get a p1776 code on 2002 dodge intrepid


P1776 is the code for soleniod stuck in low,reverse. Probably just need to have your fluid flushed and get a new solenoid pack.

Nov 17, 2011 | 2002 Dodge Intrepid

1 Answer

Car bucks and going over 40mph and has the following codes P0016, P0344, P0700, P0841, P1776


hello, Clear the codes by disconnecting battery for 10 mins then reconnect then re check for codes. Let me know, Lee

Sep 16, 2010 | 2004 Dodge Intrepid

1 Answer

After getting the up to about 55-65mph then slow down to under 40mph it seems that the trans will not go back in to over drive, and now when it happens I get a low end tap as I go over 45mph and a light...


You need to have the solenoid inside your transmission replaced. That is the P1776 code, and it is what is causing the P0700 code.

Also, make sure to do a transmission fluid flush and change, along with changing the transmission filter.

Sep 02, 2010 | 2004 Dodge Intrepid

2 Answers

I have a 2004 Dodge Intrepid SE and the check engine light has been on for several days. I took it to Auto Zone and they plugged in their tester. They gave me the following codes - P1776 and P0700. Please...


P0700 code is a generic code for Transmission Control System Malfunction


P1776 code means your solenoid switch valve is stuck in low reverse. (DTC 47) A stuck solenoid switch valve is a common occurrence in the valve body of the Dodge 41te transmission.

The first step would be to check the wiring to the solenoid from the TCM, then maybe try a new solenoid pack if the wiring is determined to be fine.

Jan 06, 2010 | 2004 Dodge Intrepid

1 Answer

I have a 2002 intrepid SXT 3.5L automatic trans(not the auto stick version) Just got codes PO700 and P1776 Would like to know what the codes indicate, and what repairs could be needed?


The p0700 means that there is a code in the trans controller. This code would then be the p1776. When the code was set the trans went into what they call "limp in mode". This is a safety feature that allows the vehicle to still driven in second gear so to make it to a repair shop or off the road.

P1776 is solenoid switch valve is latched in low/reverse. The most likely cause is the electrical portion of the trans which is called the solenoid pack. In order to replace this you need to remove the valve body inside the trans because it is bolted to the top side of it. I recommend making sure when the trans pan is dropped that there is no debris in the pan. If debris is found that the unit may need to be removed, torn down, and inspected to make sure there is no other problems.


Benjamin

Jul 17, 2009 | 2002 Dodge Intrepid

1 Answer

I have a 2002 intrepid SXT 3.5L automatic trans(not the auto stick version) Just got codes PO700 and P1776 Would like to know what the codes indicate, and what repairs could be needed?


P0700 is an alert code the p1776 is the actual trouble code.
Code p1776 is solenoid switch valve latched in low/reverse position. Valve is located in valve body not solenoid body reploace it

Jul 17, 2009 | 1999 Dodge Caravan

Not finding what you are looking for?
2004 Dodge Intrepid Logo

Related Topics:

117 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8201 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...